After the EQ is created, it can possibly generate interrupts and the interrupt
handler is referencing eq->dev. It is therefore required to set eq->dev before
calling request_irq() so if an event is generated before request_irq() returns,
we will have a valid eq->dev field.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the ports phys are connected to the switches internal MDIO bus,
we need to connect the phy to the slave netdev, otherwise
auto-negotiation etc, does not work.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRyo Munakata <ryomnktml@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

when cpsw is build as modulea and simple insert and removal of module
creates a deadlock, due to delete timer. the timer is created and destroyed
in cpsw_ale_start and cpsw_ale_stop which are from device open and close.

root@am437x-evm:~# modprobe -r ti_cpsw
[  158.505333] INFO: trying to register non-static key.
[  158.510623] the code is fine but needs lockdep annotation.
[  158.516448] turning off the locking correctness validator.
[  158.522282] CPU: 0 PID: 1339 Comm: modprobe Not tainted 3.14.23-00445-gd41c88f #44
[  158.530359] [<c0015380>] (unwind_backtrace) from [<c0012088>] (show_stack+0x10/0x14)
[  158.538603] [<c0012088>] (show_stack) from [<c054ad70>] (dump_stack+0x78/0x94)
[  158.546295] [<c054ad70>] (dump_stack) from [<c0088008>] (__lock_acquire+0x176c/0x1b74)
[  158.554711] [<c0088008>] (__lock_acquire) from [<c0088944>] (lock_acquire+0x9c/0x104)
[  158.563043] [<c0088944>] (lock_acquire) from [<c004e520>] (del_timer_sync+0x44/0xd8)
[  158.571289] [<c004e520>] (del_timer_sync) from [<bf2eac1c>] (cpsw_ale_destroy+0x10/0x3c [ti_cpsw])
[  158.580821] [<bf2eac1c>] (cpsw_ale_destroy [ti_cpsw]) from [<bf2eb268>] (cpsw_remove+0x30/0xa0 [ti_cpsw])
[  158.591000] [<bf2eb268>] (cpsw_remove [ti_cpsw]) from [<c035ef44>] (platform_drv_remove+0x18/0x1c)
[  158.600527] [<c035ef44>] (platform_drv_remove) from [<c035d8bc>] (__device_release_driver+0x70/0xc8)
[  158.610236] [<c035d8bc>] (__device_release_driver) from [<c035e0d4>] (driver_detach+0xb4/0xb8)
[  158.619386] [<c035e0d4>] (driver_detach) from [<c035d6e4>] (bus_remove_driver+0x4c/0x90)
[  158.627988] [<c035d6e4>] (bus_remove_driver) from [<c00af2a8>] (SyS_delete_module+0x10c/0x198)
[  158.637144] [<c00af2a8>] (SyS_delete_module) from [<c000e580>] (ret_fast_syscall+0x0/0x48)
[  179.524727] INFO: rcu_sched detected stalls on CPUs/tasks: {} (detected by 0, t=2102 jiffies, g=1487, c=1486, q=6)
[  179.535741] INFO: Stall ended before state dump start
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ATM, txq_reclaim will dequeue and free an skb for each tx desc released
by the hw that has TX_LAST_DESC set. However, in case of TSO, each
hw desc embedding the last part of a segment has TX_LAST_DESC set,
losing the one-to-one 'last skb frag'/'TX_LAST_DESC set' correspondance,
which causes data corruption.

Fix this by checking TX_ENABLE_INTERRUPT instead of TX_LAST_DESC, and
warn when trying to dequeue from an empty txq (which can be symptomatic
of releasing skbs prematurely).

Fixes: 3ae8f4e0 ('net: mv643xx_eth: Implement software TSO')
Reported-by: NSlawomir Gajzner <slawomir.gajzner@gmail.com>
Reported-by: NJulien D'Ascenzio <jdascenzio@yahoo.fr>
Signed-off-by: NKarl Beldan <karl.beldan@rivierawaves.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

if_bridge.h uses struct in6_addr ip6, but wasn't including the in6.h
header.  Thomas Backlund originally sent a patch to do this, but this
revealed a redefinition issue: https://lkml.org/lkml/2013/1/13/116

The redefinition issue should have been fixed by the following Linux
commits:
ee262ad8 inet: defines IPPROTO_* needed for module alias generation
cfd280c9 net: sync some IP headers with glibc

and the following glibc commit:
6c82a2f8d7c8e21e39237225c819f182ae438db3 Coordinate IPv6 definitions for Linux and glibc

so actually include the header now.
Reported-by: NColin Guthrie <colin@mageia.org>
Reported-by: NChristiaan Welvaart <cjw@daneel.dyndns.org>
Reported-by: NThomas Backlund <tmb@mageia.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: NGregory Fong <gregory.0xf0@gmail.com>
Acked-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ueki Kohei reported that when we are using NewReno with connections that
have a very low traffic, we may timeout the connection too early if a
second loss occurs after the first one was successfully acked but no
data was transfered later. Below is his description of it:

When SACK is disabled, and a socket suffers multiple separate TCP
retransmissions, that socket's ETIMEDOUT value is calculated from the
time of the *first* retransmission instead of the *latest*
retransmission.

This happens because the tcp_sock's retrans_stamp is set once then never
cleared.

Take the following connection:

                      Linux                    remote-machine
                        |                           |
         send#1---->(*1)|--------> data#1 --------->|
                  |     |                           |
                 RTO    :                           :
                  |     |                           |
                 ---(*2)|----> data#1(retrans) ---->|
                  | (*3)|<---------- ACK <----------|
                  |     |                           |
                  |     :                           :
                  |     :                           :
                  |     :                           :
                16 minutes (or more)                :
                  |     :                           :
                  |     :                           :
                  |     :                           :
                  |     |                           |
         send#2---->(*4)|--------> data#2 --------->|
                  |     |                           |
                 RTO    :                           :
                  |     |                           |
                 ---(*5)|----> data#2(retrans) ---->|
                  |     |                           |
                  |     |                           |
                RTO*2   :                           :
                  |     |                           |
                  |     |                           |
      ETIMEDOUT<----(*6)|                           |

(*1) One data packet sent.
(*2) Because no ACK packet is received, the packet is retransmitted.
(*3) The ACK packet is received. The transmitted packet is acknowledged.

At this point the first "retransmission event" has passed and been
recovered from. Any future retransmission is a completely new "event".

(*4) After 16 minutes (to correspond with retries2=15), a new data
packet is sent. Note: No data is transmitted between (*3) and (*4).

The socket's timeout SHOULD be calculated from this point in time, but
instead it's calculated from the prior "event" 16 minutes ago.

(*5) Because no ACK packet is received, the packet is retransmitted.
(*6) At the time of the 2nd retransmission, the socket returns
ETIMEDOUT.

Therefore, now we clear retrans_stamp as soon as all data during the
loss window is fully acked.

Reported-by: Ueki Kohei
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: NMarcelo Ricardo Leitner <mleitner@redhat.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Tested-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Giuseppe Cavallaro says:

====================
stmmac: review and fix lock and atomicity

Recently some issues have been reported for the driver for locking mechanism
and atomicity.

In fact, enabling DEBUG support to prove lock and to verify if sleeping while
atomic context some warnings occur at runtime. I have reproduced all on STi
platforms.

Concerning the tx path, I had provided a patch time ago but
I discarded the idea to completely remove locks; in this patch-set we can have
some useful fixes instead of.

This patch-set is to fix the atomicity in the PM stuff where I tried to collect
all the points and advice reported in the past weeks.
As final result, on my side no warnings and no problem when suspend/resume the
driver on STi boxes.

I also added a patch that fixes the locks for the EEE.
As pointed in some thread there was a design problem behind the eee
initialization and I have tried to fix that before.
As final result no issues when proving locks too.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is to fix the atomicity when suspend and resume the
driver. The clk api have been changed (as reported by Hao Liang)
and the skb allocation is done out of the hw setup function and
taking care about the GFP flags.
Reported-by: NHao Liang <hliang1025@gmail.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Hao Liang <hliang1025@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch aims to fix the concurrency in eee initialization
inside the stmmac driver and related warnings when enable
DEBUG_ATOMIC_SLEEP.

Prior this patch, the stmmac_eee_init could be called in several places
as shown below:

stmmac_open  stmmac_resume         PHY Layer
    |            |                     |
  stmmac_hw_setup           stmmac_adjust_link
    |                                  |           stmmac ethtool
    |__________________________|______________|
                                       |
                                 stmmac_eee_init

The patch removes the stmmac_eee_init call inside the stmmac_hw_setup
that is unnecessary. It is sufficient to call it in the adjust_link to
always guarantee that EEE is always configured at mac level too.

Fixing the lock protection now it is covered another case (not
considered before). The stmmac_eee_init could be called by the ethtool
so critical sections must be protected inside this function too.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When compile with CONFIG_PROVE_LOCKING the following warnings happen:

[snip]

    HARDIRQ-ON-W at:
                        [<c0480c1c>] _raw_spin_lock+0x3c/0x4c
                        [<c02c2828>] stmmac_set_rx_mode+0x18/0x3c
                        [<c038b2cc>] dev_set_rx_mode+0x1c/0x28
                        [<c038b38c>] __dev_open+0xb4/0xf8
                        [<c038b5a8>] __dev_change_flags+0x94/0x128
                        [<c038b6a8>] dev_change_flags+0x10/0x48
                        [<c062afe0>] ip_auto_config+0x1d4/0x1084
                        [<c000873c>] do_one_initcall+0x108/0x15c
                        [<c060ec50>] kernel_init_freeable+0x1a8/0x248
                        [<c0472cc0>] kernel_init+0x8/0x160
                        [<c000dfc8>] ret_from_fork+0x14/0x2c
     INITIAL USE at:
                       [<c0480c1c>] _raw_spin_lock+0x3c/0x4c
                       [<c02c2828>] stmmac_set_rx_mode+0x18/0x3c
                       [<c038b2cc>] dev_set_rx_mode+0x1c/0x28
                       [<c038b38c>] __dev_open+0xb4/0xf8
                       [<c038b5a8>] __dev_change_flags+0x94/0x128
                       [<c038b6a8>] dev_change_flags+0x10/0x48
                       [<c062afe0>] ip_auto_config+0x1d4/0x1084
                       [<c000873c>] do_one_initcall+0x108/0x15c
                       [<c060ec50>] kernel_init_freeable+0x1a8/0x248
                       [<c0472cc0>] kernel_init+0x8/0x160
                       [<c000dfc8>] ret_from_fork+0x14/0x2c

so the patch just removes the lock protection in the stmmac_set_rx_mode
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Emilio Lopez <emilio@elopez.com.ar>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add missing spin_unlock when tx frames gets dropped.
Signed-off-by: NFabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

stmmac_tx_avail() may lie if used unprotected. It's using cur_tx
and dirty_tx index. These index may be already in use by tx_clean
when entering xmit routine. So, this should be called locked.

This can cause transmit queue to be stuck, with following message:
NETDEV WATCHDOG: eth0 (stmmaceth): transmit queue 0 timed out
Signed-off-by: NFabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers: net: ethernet: xilinx: xilinx_emaclite: revert the original commit "1db3ddff"

Microblaze is a fpga soft core, it can be customized easily, which may
cause many various hardware version strings.

So the original fix patch based on hard-coded compatible version strings
is not a good idea (although it is correct for current issue). For it,
there will be a new solving way soon (which based on the device tree).

The original issue is related with qemu, so can only change the hardware
version string in qemu for it, then keep the original driver no touch (
qemu is for virtualization which has much easier life than real world).
Signed-off-by: NChen Gang <gang.chen.5i5j@gmail.com>
Acked-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

File descriptors are always closed on exit :-)
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It was initially sent by Lorenzo Colitti, but was subsequently
lost in the final diff he submitted.
Signed-off-by: NLoganaden Velvindron <logan@elandsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The pernet ops aren't ever unregistered, which causes a memory
leak and an OOPs if the module is ever reinserted.

Fixes: 0b5e8b8e ("net: Add Geneve tunneling protocol driver")
CC: Andy Zhou <azhou@nicira.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>
Acked-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Geneve does not currently set the inner protocol type when
transmitting packets. This causes GSO segmentation to fail on NICs
that do not support Geneve offloading.

CC: Andy Zhou <azhou@nicira.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Iyappan Subramanian says:

====================
drivers: net: xgene: Fix crash for backward compatibility

This patch set fixes the following issues that were reported during regression.

Patch 1,2 : Adds backward compatibility with the older firmware (<= 1.13.28).
Patch 3   : Use separate hardware resources (descriptor ring, prefetch buffer)
	   that are not shared with the firmware
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the following kernel crash during SGMII based 1GbE probe.

	BUG: Bad page state in process swapper/0  pfn:40fe6ad
	page:ffffffbee37a75d8 count:-1 mapcount:0 mapping:          (null) index:0x0
	flags: 0x0()
	page dumped because: nonzero _count
	Modules linked in:
	CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.17.0+ #7
	Call trace:
	[<ffffffc000087fa0>] dump_backtrace+0x0/0x12c
	[<ffffffc0000880dc>] show_stack+0x10/0x1c
	[<ffffffc0004d981c>] dump_stack+0x74/0xc4
	[<ffffffc00012fe70>] bad_page+0xd8/0x128
	[<ffffffc000133000>] get_page_from_freelist+0x4b8/0x640
	[<ffffffc000133260>] __alloc_pages_nodemask+0xd8/0x834
	[<ffffffc0004194f8>] __netdev_alloc_frag+0x124/0x1b8
	[<ffffffc00041bfdc>] __netdev_alloc_skb+0x90/0x10c
	[<ffffffc00039ff30>] xgene_enet_refill_bufpool+0x11c/0x280
	[<ffffffc0003a11a4>] xgene_enet_process_ring+0x168/0x340
	[<ffffffc0003a1498>] xgene_enet_napi+0x1c/0x50
	[<ffffffc00042b454>] net_rx_action+0xc8/0x18c
	[<ffffffc0000b0880>] __do_softirq+0x114/0x24c
	[<ffffffc0000b0c34>] irq_exit+0x94/0xc8
	[<ffffffc0000e68a0>] __handle_domain_irq+0x8c/0xf4
	[<ffffffc000081288>] gic_handle_irq+0x30/0x7c

This was due to hardware resource sharing conflict with the firmware. This
patch fixes this crash by using resources (descriptor ring, prefetch buffer)
that are not shared.
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NKeyur Chudgar <kchudgar@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support when used with older firmware (<= 1.13.28).

- Added xgene_ring_mgr_init() to check whether ring manager is initialized
- Calling xgene_ring_mgr_init() from xgene_port_ops.reset()
- To handle errors, changed the return type of xgene_port_ops.reset()
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NKeyur Chudgar <kchudgar@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following kernel crash was reported when using older firmware (<= 1.13.28).

[    0.980000] libphy: APM X-Gene MDIO bus: probed
[    1.130000] Unhandled fault: synchronous external abort (0x96000010) at 0xffffff800009a17c
[    1.140000] Internal error: : 96000010 [#1] SMP
[    1.140000] Modules linked in:
[    1.140000] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.17.0+ #21
[    1.140000] task: ffffffc3f0110000 ti: ffffffc3f0064000 task.ti: ffffffc3f0064000
[    1.140000] PC is at ioread32+0x58/0x68
[    1.140000] LR is at xgene_enet_setup_ring+0x18c/0x1cc
[    1.140000] pc : [<ffffffc0003cec68>] lr : [<ffffffc00053dad8>] pstate: a0000045
[    1.140000] sp : ffffffc3f0067b20
[    1.140000] x29: ffffffc3f0067b20 x28: ffffffc000aa8ea0
[    1.140000] x27: ffffffc000bb2000 x26: ffffffc000a64270
[    1.140000] x25: ffffffc000b05ad8 x24: ffffffc0ff99ba58
[    1.140000] x23: 0000000000004000 x22: 0000000000004000
[    1.140000] x21: 0000000000000200 x20: 0000000000200000
[    1.140000] x19: ffffffc0ff99ba18 x18: ffffffc0007a6000
[    1.140000] x17: 0000000000000007 x16: 000000000000000e
[    1.140000] x15: 0000000000000001 x14: 0000000000000000
[    1.140000] x13: ffffffbeedb71320 x12: 00000000ffffff80
[    1.140000] x11: 0000000000000002 x10: 0000000000000000
[    1.140000] x9 : 0000000000000000 x8 : ffffffc3eb2a4000
[    1.140000] x7 : 0000000000000000 x6 : 0000000000000000
[    1.140000] x5 : 0000000001080000 x4 : 000000007d654010
[    1.140000] x3 : ffffffffffffffff x2 : 000000000003ffff
[    1.140000] x1 : ffffff800009a17c x0 : ffffff800009a17c

The issue was that the older firmware does not support 10GbE and
SGMII based 1GBE interfaces.

This patch changes the address length of the reg property of sgmii0 and xgmii
nodes and serves as preparatory patch for the fix.
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NKeyur Chudgar <kchudgar@apm.com>
Reported-by: NDann Frazier <dann.frazier@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

efx_ef10_probe() was BUGging out if the BAR2 size was 0.  This is
 unnecessarily violent; instead we should just fail to probe the device.
Kept a WARN_ON as this problem indicates a broken or misconfigured NIC.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
ipv6: Fix iflink setting for ipv6 tunnels

The ipv6 tunnels do the dev->iflink setting too early, it gets
overwritten by register_netdev(). So set dev->iflink from within
a ndo_init function to keep the configured setting.

This patchset fixes this for ip6_tunnel, vti6, sit and gre6.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Otherwise it gets overwritten by register_netdev().
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ipip6_tunnel_init() sets the dev->iflink via a call to
ipip6_tunnel_bind_dev(). After that, register_netdevice()
sets dev->iflink = -1. So we loose the iflink configuration
for ipv6 tunnels. Fix this by using ipip6_tunnel_init() as the
ndo_init function. Then ipip6_tunnel_init() is called after
dev->iflink is set to -1 from register_netdevice().
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

vti6_dev_init() sets the dev->iflink via a call to
vti6_link_config(). After that, register_netdevice()
sets dev->iflink = -1. So we loose the iflink configuration
for vti6 tunnels. Fix this by using vti6_dev_init() as the
ndo_init function. Then vti6_dev_init() is called after
dev->iflink is set to -1 from register_netdevice().
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ip6_tnl_dev_init() sets the dev->iflink via a call to
ip6_tnl_link_config(). After that, register_netdevice()
sets dev->iflink = -1. So we loose the iflink configuration
for ipv6 tunnels. Fix this by using ip6_tnl_dev_init() as the
ndo_init function. Then ip6_tnl_dev_init() is called after
dev->iflink is set to -1 from register_netdevice().
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When VLAN is in use in macvtap_put_user, we end up setting
csum_start to the wrong place.  The result is that the whoever
ends up doing the checksum setting will corrupt the packet instead
of writing the checksum to the expected location, usually this
means writing the checksum with an offset of -4.

This patch fixes this by adjusting csum_start when VLAN tags are
detected.

Fixes: f09e2249 ("macvtap: restore vlan header on user read")
Cc: stable@vger.kernel.org
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Cheers,
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On i.MX6SX sdb platform, there has two same enet MACs, after system up,
just eth0 is up, and then do suspend/resume test:

[   50.437967] PM: Syncing filesystems ... done.
[   50.476924] Freezing user space processes ... (elapsed 0.005 seconds) done.
[   50.490093] Freezing remaining freezable tasks ... (elapsed 0.004 seconds) done.
[   50.559771] ------------[ cut here ]------------
[   50.564453] WARNING: CPU: 0 PID: 575 at drivers/clk/clk.c:851 __clk_disable+0x60/0x6c()
[   50.572475] Modules linked in:
[   50.575578] CPU: 0 PID: 575 Comm: sh Not tainted 3.18.0-rc2-next-20141031-00007-gf61135b #21
[   50.584031] Backtrace:
[   50.586550] [<80011ecc>] (dump_backtrace) from [<8001206c>] (show_stack+0x18/0x1c)
[   50.594136]  r6:808a7a54 r5:00000000 r4:00000000 r3:00000000
[   50.599920] [<80012054>] (show_stack) from [<806ab3c0>] (dump_stack+0x80/0x9c)
[   50.607187] [<806ab340>] (dump_stack) from [<8002a3e8>] (warn_slowpath_common+0x6c/0x8c)
[   50.615294]  r5:00000353 r4:00000000
[   50.618940] [<8002a37c>] (warn_slowpath_common) from [<8002a42c>] (warn_slowpath_null+0x24/0x2c)
[   50.627738]  r8:00000000 r7:be144c44 r6:be015600 r5:80070013 r4:be015600
[   50.634573] [<8002a408>] (warn_slowpath_null) from [<804f8d4c>] (__clk_disable+0x60/0x6c)
[   50.642777] [<804f8cec>] (__clk_disable) from [<804f8e5c>] (clk_disable+0x2c/0x38)
[   50.650359]  r4:be015600 r3:00000000
[   50.654006] [<804f8e30>] (clk_disable) from [<80420ab4>] (fec_enet_clk_enable+0xc4/0x258)
[   50.662196]  r5:be3cb620 r4:be3cb000
[   50.665838] [<804209f0>] (fec_enet_clk_enable) from [<80421178>] (fec_suspend+0x30/0x180)
[   50.674026]  r7:be144c44 r6:be144c10 r5:8037f5a4 r4:be3cb000
[   50.679802] [<80421148>] (fec_suspend) from [<8037f5d8>] (platform_pm_suspend+0x34/0x64)
[   50.687906]  r10:00000000 r9:00000000 r8:00000000 r7:be144c44 r6:be144c10 r5:8037f5a4
[   50.695852]  r4:be144c10 r3:80421148
[   50.699511] [<8037f5a4>] (platform_pm_suspend) from [<8038784c>] (dpm_run_callback.isra.14+0x34/0x6c)
[   50.708764] [<80387818>] (dpm_run_callback.isra.14) from [<80387f00>] (__device_suspend+0x12c/0x2a4)
[   50.717909]  r9:8098ec8c r8:80973bec r6:00000002 r5:811c7038 r4:be144c10
[   50.724746] [<80387dd4>] (__device_suspend) from [<803894fc>] (dpm_suspend+0x64/0x224)
[   50.732675]  r8:80973bec r7:be144c10 r6:8098ec24 r5:811c7038 r4:be144cc4
[   50.739509] [<80389498>] (dpm_suspend) from [<8038999c>] (dpm_suspend_start+0x60/0x68)
[   50.747438]  r10:8082fa24 r9:00000000 r8:00000004 r7:00000003 r6:00000000 r5:8116ec80
[   50.755386]  r4:00000002
[   50.757969] [<8038993c>] (dpm_suspend_start) from [<800679d8>] (suspend_devices_and_enter+0x90/0x3ec)
[   50.767202]  r4:00000003 r3:8116eca0
[   50.770843] [<80067948>] (suspend_devices_and_enter) from [<80067f40>] (pm_suspend+0x20c/0x2a4)
[   50.779553]  r8:00000004 r7:00000003 r6:00000000 r5:8116ec8c r4:00000003
[   50.786394] [<80067d34>] (pm_suspend) from [<80066858>] (state_store+0x70/0xc0)
[   50.793718]  r6:8116ec90 r5:00000003 r4:bd88a800 r3:0000006d
[   50.799496] [<800667e8>] (state_store) from [<802b0384>] (kobj_attr_store+0x1c/0x28)
[   50.807251]  r10:bd399f78 r8:00000000 r7:bd88a800 r6:bd88a800 r5:00000004 r4:bd085680
[   50.815219] [<802b0368>] (kobj_attr_store) from [<80153090>] (sysfs_kf_write+0x54/0x58)
[   50.823252] [<8015303c>] (sysfs_kf_write) from [<80151fd8>] (kernfs_fop_write+0xd0/0x194)
[   50.831441]  r6:00000004 r5:bd08568c r4:bd085680 r3:8015303c
[   50.837220] [<80151f08>] (kernfs_fop_write) from [<800eddb4>] (vfs_write+0xb8/0x1a8)
[   50.844975]  r10:00000000 r9:00000000 r8:00000000 r7:bd399f78 r6:01336408 r5:00000004
[   50.852924]  r4:bc584dc0
[   50.855505] [<800edcfc>] (vfs_write) from [<800ee0b8>] (SyS_write+0x48/0x88)
[   50.862567]  r10:00000000 r8:00000000 r7:01336408 r6:00000004 r5:bc584dc0 r4:bc584dc0
[   50.870537] [<800ee070>] (SyS_write) from [<8000eb00>] (ret_fast_syscall+0x0/0x48)
[   50.878120]  r9:bd398000 r8:8000ecc4 r7:00000004 r6:76f42b48 r5:01336408 r4:00000004
[   50.885983] ---[ end trace 7545115d752a316a ]---
[   50.890765] ------------[ cut here ]------------

The root cause is that eth1 is not opened and clock is not enabled, and .suspend() still
call .fec_enet_clk_enable() to disable clock.

To avoid the broken, let it check network device up status by calling .netif_running()
before disable/enable clocks.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Herbert Xu says:

====================
tun: Fix csum_start and TUN_PKT_STRIP

The first patch fixes a serious problem that breaks checksum offload
in VMs while the second patch fixes a problem that probably affects
no one.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We set the flag TUN_PKT_STRIP if the user buffer provided is too
small to contain the entire packet plus meta-data.  However, this
has been broken ever since we added GSO meta-data.  VLAN acceleration
also has the same problem.

This patch fixes this by taking both into account when setting the
TUN_PKT_STRIP flag.

The fact that this has been broken for six years without anyone
realising means that nobody actually uses this flag.

Fixes: f43798c2 ("tun: Allow GSO using virtio_net_hdr")
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When VLAN acceleration is in use on the xmit path, we end up
setting csum_start to the wrong place.  The result is that the
whoever ends up doing the checksum setting will corrupt the packet
instead of writing the checksum to the expected location, usually
this means writing the checksum with an offset of -4.

This patch fixes this by adjusting csum_start when VLAN acceleration
is detected.

Fixes: 6680ec68 ("tuntap: hardware vlan tx support")
Cc: stable@vger.kernel.org
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The makefile for sanitizing kernel headers uses the kbuild file
to determine which files to do. Several networking related headers
were missing. Without these headers iproute2 build would break.
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix:
net/bridge/netfilter/nft_reject_bridge.c:
In function 'nft_reject_br_send_v6_unreach':
net/bridge/netfilter/nft_reject_bridge.c:240:3:
	error: implicit declaration of function 'csum_ipv6_magic'
   csum_ipv6_magic(&nip6h->saddr, &nip6h->daddr,
   ^
make[3]: *** [net/bridge/netfilter/nft_reject_bridge.o] Error 1

Seen with powerpc:allmodconfig.

Fixes: 523b929d ("netfilter: nft_reject_bridge: don't use IP stack to reject traffic")
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SMC91x is written to explicitly look up the IRQ resource
from the platform device and extract the IRQ and flags, however
the platform_get_irq() does additional things, like call
of_irq_get() in the device tree case, which will translate
the IRQ using the irqdomain and defer the probe if the
IRQ host cannot be found.

As we're not looking up the resource, this will not retrieve
the IRQ flags, but that is better done using
irqd_get_trigger_type(), as the trigger is what the driver
wants to modify. We take care to preserve the semantics that
will make the trigger type provided from the resource
override any local specifier.

Tested on the Nomadik NHK15 which has its SMC91x IRQ line
connected to a STMPE2401 GPIO expander on I2C.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers: net: ethernet: xilinx: xilinx_emaclite: Compatible with 'xlnx, xps-ethernetlite-2.00.b' for QEMU using

When use current latest upstream qemu (current version: 2.1.2), need let
driver compatible with 'xlnx,xps-ethernetlite-2.00.b', or can not find
net device in microblaze qemu. Related QEMU commands under fedora 20:

  yum install libvirt
  yum install tunctl
  tunctl -b
  ip link set tap0 up
  brctl addif virbr0 tap0
  ./microblaze-softmmu/qemu-system-microblaze -M petalogix-s3adsp1800 \
    -kernel ../linux-stable.microblaze/arch/microblaze/boot/linux.bin \
    -no-reboot -append "console=ttyUL0,115200 doreboot" -nographic \
    -net nic,vlan=0,model=xlnx.xps-ethernetlite,macaddr=00:16:35:AF:94:00 \
    -net tap,vlan=0,ifname=tap0,script=no,downscript=no

  in microblaze qemu bash (guest machine):

    ifconfig eth0 add 192.168.122.2 netmask 255.255.255.0
    ifconfig eth0 up

After add this patch, can find the device, and can be used by 'telnetd'
(need cross-build busybox with glibc for it), then outside can telnet to
it without password.
Signed-off-by: NChen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: systemport: TX dma fixes

This patch series contains two fixes for our transmit path, first one
is a pretty nasty one since we were not allocating a large enough
dma coherent pool for our transmit descriptors, which would work most of the
time, since allocations are contiguous and we could have.

Second patch fixes a less frequent, though highly likley crash when using
CMA allocations.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Callers of bcm_sysport_init_tx_ring() can currently fail, and will
always call bcm_sysport_fini_tx_ring() in a loop ending at the number of
TX queues (32) without checking if the TX ring was successfully
initialized or not.

Update bcm_sysport_fini_tx_ring() to return early and avoid a crash
de-referencing ring->cbs if the TX ring was not initialized, since
ring->cbs is the last part of the initialization done by
bcm_sysport_init_tx_ring() that could fail.

Fixes: 80105bef ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Reported-by: NMaxime Bizon <mbizon@freebox.fr>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should not be allocating a single byte of DMA coherent memory, but
instead a full-sized struct dma_desc (8 bytes).

Fixes: 80105bef ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>