Add Video Processing Unit and CVBS Output nodes, and enable CVBS on selected
boards.
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Signed-off-by: NKevin Hilman <khilman@baylibre.com>

The SCPI driver has an updated compatible to indicate the pre-released
(pre v1.0) status of the driver.  Since Amlogic used a pre-1.0
version, add that compatible as well.
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

The Nexbox A95X exists with a Meson GXBB (S905) Soc or a Meson GXL SoC (S905X).
Add the S905X variant which uses the internal PHY instead of an external PHY.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Add support for the Nexbox A1 board based on the Amlogic S912 SoC.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
[khilman: replace '_' in node-names with '-']
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Following the Amlogic Linux kernel, it seem the only differences
between the GXL and GXM SoCs are the CPU Clusters.

This commit renames the gxl-s905d-p23x DTSI in a common file for
S905D p23x and S912 q20x boards.

Then adds a meson-gxm dtsi and reproduce the P23x to Q20x boards
dts files since the S905D and S912 SoCs shares the same pinout
and the P23x and Q20x boards are identical.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Tested-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

When the USB PHY driver was introduced the reset framework did not
have support for triggering a reset pulse for shared resets. On GXBB
however there is only one reset line for both PHYs (meaning we have a
shared reset line). With the latest changes to the reset framework and
the corresponding updates to the phy-meson8b-usb2 driver we can now pass
the reset to the second PHY as well.
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

All boards from the Tronsmart Vega S95 series are sharing similar MMC
based hardware.
sd_emmc_a is used to connect a Broadcom based SDIO wifi card (supported
by the brcmfmac driver). The 32.768KHz LPO clock for the wifi chip is
generated by PWM_E.
sd_emmc_b is routed to the SD-card. Unlike p20x there is no GPIO
regulator, meaning it only supports 3.3V (which seems to be hard-wired).
The eMMC chip is connected to sd_emmc_c and is implemented similar to
the meson-gxbb-p20x boards (meaning that hard-wired fixed regulators
are used).
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Enable Ethernet on the p23x board, pinctrl attribute is only added for
the p230 board since the p231 only uses the Internal PHY.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Add Ethernet node with Internal PHY selection for the Amlogic GXL SoCs
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

meson-gx.dtsi was directly derived from meson-gxbb.dtsi, so keep the
copyrights in chronological order to not give a wrong impression.

Fixes: c328666d ("ARM64: dts: amlogic: Add Meson GX dtsi from GXBB")
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: NAndreas Färber <afaerber@suse.de>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Enable the Infraread Receiver on the p23x board.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Add SD/SDIO/MMC nodes and PWM 32768Hz clock configuration to provide
storage and WiFi functionality on the p23x boards.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Add pinctrl attribute to p23x uart node.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Add MMC/SD/SDIO nodes clock attributes for Amlogic Meson GXL.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Add i2c nodes clock attributes for Amlogic Meson GXL.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Add clock node for Amlogic Meson GXL.
The GXBB compatible is retained since the GXBB clock tree is used for now.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Add pinctrl nodes and pin definitions for Amlogic Meson GXL.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
[khilman: use GXBB include until GXL pinctrl support merged]
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Move common nodes between GXBB and GXL in to the common GX dtsi.
Leave the clock attributes in the GXBB dtsi for now.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Add support for eMMC/SD/SDIO on the Nexbox A95x.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Add Wifi module support on the Amlogic P20x boards on the SDIO port.
The Wifi module also needs a 32768Hz clock provided by the PWM E port
through a pwm-clock node in it's power sequence.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Add a 32768Hz clock generated by the PWM E port used by the WiFi module.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Add binding and basic support for the SD/eMMC controller on Amlogic
S905/GXBB devices.
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
[narmstrong: added nodes for GX, enabled SDIO on P20x]
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Enable both gxbb USB controller and add a 5V regulator for the OTG port
VBUS
Signed-off-by: NBrian Kim <brian.kim@hardkernel.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

For boards only supporting 10/100 ethernet over a RMII PHY link, add
a separate pinctrl node. By the way, rename the existing node to rgmii
specific naming in all boards dts.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

In order to remove the boot warning :
[    2.290933] Unable to detect cache hierarchy from DT for CPU 0
And add missing L2 cache hierarchy information, add a simple l2 cache node
and reference it from the A53 cpu nodes.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Add support for the S905 (GXBB) version of the Nexbox A95X.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

This patch introduces the basic support for the Amlogic S905D (MesonGXL)
and for the Amlogic evaluation boards P230 and P231.
No documentation has been released yet for this SoC, so for now only the
bare minimum has been added in the DT.
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

This patch introduces the basic support for the Amlogic S905X (Meson
GXL) and for the Amlogic evaluation board P212.
No documentation has been released yet for this SoC, so for now only the
bare minimum has been added in the DT.
Acked-by: NRob Herring <robh@kernel.org>
Reviewed-by: NAndreas Färber <afaerber@suse.de>
Signed-off-by: NCarlo Caione <carlo@endlessm.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Move all non-gxbb specific nodes to a common GX dtsi.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Enable both gxbb USB controller and add a 5V regulator for the OTG port
VBUS
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Enable both gxbb USB controller and add a 5V regulator for the OTG port
VBUS
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
[khilman: rename vbus node to match P200 schematics]
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

The ARM architected timer specification mandates that the interrupt
associated with each timer is level triggered (which corresponds to
the "counter >= comparator" condition).

A number of DTs are being remarkably creative, declaring the interrupt
to be edge triggered. A quick look at the TRM for the corresponding ARM
CPUs clearly shows that this is wrong, and I've corrected those.
For non-ARM designs (and in the absence of a publicly available TRM),
I've made them active low as well, which can't be completely wrong
as the GIC cannot disinguish between level low and level high.

The respective maintainers are of course welcome to prove me wrong.

While I was at it, I took the liberty to fix a couple of related issue,
such as some spurious affinity bits on ThunderX, and their complete
absence on ls1043a (both of which seem to be related to copy-pasting
from other DTs).
Acked-by: NDuc Dang <dhdang@apm.com>
Acked-by: NCarlo Caione <carlo@endlessm.com>
Acked-by: NMichal Simek <michal.simek@xilinx.com>
Acked-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Add the nodes for the dwc2 USB controller and the related USB PHYs.
Currently we force usb0 to host mode because OTG is currently not
working in our PHY driver.
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Add nodes for i2c bus on gxbb based platforms.
On the OdroidC2 (I2C A) and P200 (I2C B), the pull-up resistor are
present directly on the board. This indicates that these pins are
dedicated to i2c.
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>