Rename r8a7790_init_delay() into r8a7790_init_early()
to make the function name show that more than just
delay setup may happen in the future.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Update the Lager DT reference code to get rid of the redundant
irqchip header and also make lager_add_standard_devices() static.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This is sufficient to allow boot of the Lager board with
a console without boards-lager.c compiled into the kernel.
This is an example of a minimal but still useful initialisation
of the board using DT as much as possible.

As such it is the same as the boot of Lager that can be achieved
without a board file. The intention of adding this file
is to facilitate further work to allow board specific devices to be
initialised via DT.
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add a DT reference implementation for the KZM9D board.

Only DT devices are used in this case. UART, STI, GPIO
and SMP / GIC are all provided by emev2.dtsi.

There is still a board specific C file used for enabling
legacy SH clocks. This file will be removed after we have
moved over to common clocks.
Signed-off-by: NMagnus Damm <damm@opensource.se>
[horms+renesas@verge.net.au: Do not include trailing blank line in
 board-kzm9d-reference.c ]
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add support for early console to the SH-Mobile boards.

Simply perform an early platform probe for "earlyprintk"
to trigger the early serial console code in sh-sci.c.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Optimize the SH-Mobile interrupt assembly macros to avoid
reloading the INTFLGA register address in case of multiple
pending interrupts. Kindly pointed out by Russell King.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds preliminary support for the SH-Mobile G-series.

The SH-Mobile G-series is a series of ARM/SH multi-core CPUs that aside
from the ARM MPU are primarily composed of existing SH IP blocks.

This includes initial support for the SH7367 (SH-Mobile G3) CPU and
the G3EVM reference board.

Only timer, serial console, and NOR flash are supported at this point.
Patches for the interrupt controller, pinmux support, clock framework
and runtime pm will be submitted as feature patches on top of this.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds support for the Texas Instruments AR7 System-on-a-Chip.
It supports the TNETD7100, 7200 and 7300 versions of the SoC.
Signed-off-by: NMatteo Croce <matteo@openwrt.org>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NEugene Konev <ejka@openwrt.org>
Signed-off-by: NNicolas Thill <nico@openwrt.org>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Now that Linux includes support for the Atmel AT91SAM9260 and
AT91SAM9261 processors in addition to the original Atmel AT91RM9200
(with support for more AT91 processors pending), the "mach-at91rm9200"
and "arch-at91rm9200" directories should be renamed to indicate their
more generic nature.

The following git commands should be run BEFORE applying this patch:
  git-mv arch/arm/mach-at91rm9200 arch/arm/mach-at91
  git-mv include/asm-arm/arch-at91rm9200 include/asm-arm/arch-at91
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch includes a number of small changes for integrating the
AT91SAM9261 and AT91SAM0260 support.

      * Can only select support for one AT91 processor at a time.
      * Remove most of the remaining static memory mapping for the
        AT91RM9200.
      * Reserve 1Mb of memory below the IO for mapping the internal SRAM
        and any custom board-specific devices (ie, FPGA).
      * The SAM9260 has more serial ports, so increase the maximum to 7.
      * Define the standard chipselect addresses, and define other
        addresses relative to those.
      * CLOCK_TICK_RATE is different on the SAM926x's.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Andrew Victor

This patch maps the AT91RM9200's internal SRAM into the virtual memory
address space - just below the internal peripheral registers.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from SAN People

Following changes were made to clock.c:

1) Replaced <asm/hardware/clock.h> with <linux/clk.h>
2) Removed old unused clk_enable & clk_disable.
3) Replaced clk_use/clk_unuse with clk_enable/clk_disable.

Otherwise it's the same as the previous patch.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Rationalise hardware.h include.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!