To enable firmware debug messages through uart interface,

modprobe ath6kl_sdio uart_debug=1.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The change enables offloading TCP checksum calculation to firmware.
There are still some issues with the checksum offload so better to
disable it by default until the issues are resolved.

To enable TCP checksum offload for tx and rx paths, use
the ethtool as follows:
ethtool -K <interface> tx on
ethtool -K <interface> rx on

To disable TCP checksum offload, for tx and rx paths, use
the ethtool as follows:
ethtool -K <interface> tx off
ethtool -K <interface> rx off

kvalo: indentation changes
Signed-off-by: NRishi Panjwani <rpanjwan@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

As firmware starting from 3.2.0.12 has some API changes and doesn't work
with older versions of ath6kl we need to bump up the API version. This
way we don't break anything.

Also store which version of API is used and print that during boot:

ath6kl: ar6003 hw 2.1.1 sdio fw 3.2.0.13 api 3
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Currently ath6kl has just hardcoded paths to each firmware file. Change
this more dynamic by separating the the directory and file name from each
other. That way it's easier to dynamically create full paths to firmware and
code looks better. And now it's possible to remove a function needed by
devicetree code.

While at it add a structure inside struct ath6kl_hw to contain all
firmware names. I deliberately omitted board file support as
those will be handled later.

This is needed for firmware API 3.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

AR6003 family use uart_tx=8 and refclk=26Mhz by default, and AR6004 family
uses different uart_tx pin and could also support various xtal source,
moves these per hw configuration.
Signed-off-by: NRyan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath6kl firmware supports scheduled scan functionality with the wow ssid
filter. But the firmware does not send any events after scan results
so I had to add a timer which notifies about new scan results.

Sched scan needs firmware version 3.2.0.6 or later. If firmware doesn't
support sched scan the driver will not enable the feature.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

For some strange reason I used ALIGN() to calculate index to the
buffer. That is totally bogus and wouldn't work when it tried to read
the second bit. Fix it by removing the ALIGN() altogether.

Also check that ie_len is not too short.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Currently mac80211 implements these for all devices,
but given restrictions of some devices that isn't
really true, so prepare for being able to remove the
capability for some mac80211 devices.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Acked-by: NKalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The maximum number of supported virtual interfaces are 3.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Currently the max number of vifs which can be used for non-p2p
mode is determined in ath6kl_core_alloc(). But the maximum
supported vifs are parsed from firmware IE in ath6kl_fetch_fw_api2()
which would happen after ath6kl_core_alloc().
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The ath6kl responds to probe-requests in HW while operating as an AP. It
supports offloading exclusions to support the WPS, WPS2, P2P and
802.11u protocols.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Not all firmwares support multiple vifs and we need to read the limit from
the firmware image.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Needed when detecting how many vifs firmware supports.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Part of ath6kl uses "REV3" style of naming hardware versions and elsewhere
"hw 2.1.1" is used instead for the same version. This is confusing, use
the latter term everywhere.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

To make it easier to print name for each hardware type. Also move the hw
info print to ath6kl_init_hw_start() which is more logical place for it.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Board data address can change between firmwares so we need to read that
from the firmware image.

Also fix debug log for the patch address to print the address in hex.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is to make it configurable by firmware IEs. Also determine if we need
to write or read the board address to the chip by checking if board address
is set or not.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It's easier to handle the values when they are defined in a struct.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Having separate defines, in a different file, makes it difficult to read
the actual values. As we are just setting named fields in a struct
the defines don't make any sense anymore.

There are no functional changes, only moving of constants.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

These have changed a bit since last time ar6004 code was commited.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is to force ath6kl to power off hardware during suspend even if
sdio support keep power. This is needed, for example, when sdio
controller is buggy or maximum powersaving is desired.

Usage:

insmod ath6kl.ko suspend_cutpower=1
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Jouni reported that my patch "ath6kl: power down hardware when interface
is down" caused a regression on his x86 boxes and scan didn't work anymore.
I was able to reproduce the problem by disabling all debug messages.

So there has to be a race condition somewhere in the code and disable the
functionality until the race is fixed. Now hardware is powered from the
point where module is loaded until it's removed.
Reported-by: NJouni Malinen <jouni@qca.qualcomm.com>
Tested-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The following is the lockdep warning which detects possible
deadlock condition with the way ar->lock and ar->list_lock
are being used.

  (&(&ar->lock)->rlock){+.-...}, at: [<ffffffffa0492d13>] ath6kl_indicate_tx_activity+0x83/0x110 [ath6kl]
 but this lock took another, SOFTIRQ-unsafe lock in the past:
  (&(&ar->list_lock)->rlock){+.+...}

 and interrupts could create inverse lock ordering between them.

 other info that might help us debug this:
  Possible interrupt unsafe locking scenario:

        CPU0                    CPU1
        ----                    ----
   lock(&(&ar->list_lock)->rlock);
                                local_irq_disable();
                                lock(&(&ar->lock)->rlock);
                                lock(&(&ar->list_lock)->rlock);
   <Interrupt>
     lock(&(&ar->lock)->rlock);

  *** DEADLOCK ***

softirqs have to be disabled when acquiring ar->list_lock to avoid
the above deadlock condition. When the above warning printed the
interface is still up and running without issue.
Reported-by: NKalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This way it's easier to track state changes and in the future add
more warnings about using hardware in wrong states. Currently there
are few random flags for trying to do the same, those will be cleaned
and removed in the future.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Currently firmware crash dump is printed only if debug is enabled.
Change it so that the crash dump is always printed.

Also move the code from init.c to hif.c.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The benefit from this is that user space can control hardware's power state
by putting interface up and down. This is handy if firmware gets to some
weird state.

The downside will be that putting interface up takes a bit longer,
I was measuring ~500 ms during interface up.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Refactor the code needed to boot the hardware to a separate function so
that it will be easier boot and shutdown hardware.

No functional changes (hopefully).
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In preparation for splitting module initialisation and hardware boot
code from each other.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In preparation for cutting down power from the chip on the fly.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When compiling ath6kl for ARM with device tree tree compilation fails
with errors like:

include/linux/of.h: In function 'of_property_read_u32_array':
include/linux/of.h:249:10: error: 'ENOSYS' undeclared

Workaround this by including errno.h from init.c.

kvalo: improved commit log
Signed-off-by: NSangwook Lee <sangwook.lee@linaro.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Not all credit functions used that prefix, fix that.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is to follow the common style in the driver. Also add braces to
fix a style issue.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Wlan parameters need to be configured for every vif
in target.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This option lets operate more than one vif in normal mode (AP/STA/IBSS)
when support for multiple vif is enabled. This modparam needs to be used
as

modprobe ath6kl multi_norm_if_support=1
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Virtual interface information need to be configured during
init time to the target. With MAX_NUM_VIF is restricted to
1, currently only a single vif is being configured.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Use replace (un)register_netdev() with (un)register_netdevice()
so that the same ath6kl function can be used with
add_virtual_intf()/del_virtual_intf().
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patch removes all references to ar->vif and takes
vif from a list.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

WMI ready event gives the mac address, cache this
mac address in struct ath6kl so that it can be used to
compute the mac address for other vif in case of multi vif.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>