- 06 11月, 2005 2 次提交
-
-
由 Jeff Garzik 提交于
Unused, and causes the files to be needlessly rebuilt in some cases.
-
由 Matt Porter 提交于
Adds a phy_mask field to struct mii_bus and uses it. This field indicates each phy address to be ignored when probing the mdio bus. This support is needed for the fs_enet and ibm_emac drivers to be converted to the generic phy layer among other drivers. Many systems lock up on probing certain phy addresses or probing doesn't return 0xffff when nothing is found at the address. A new driver I'm working on also makes use of this mask. Signed-off-by: NMatt Porter <mporter@kernel.crashing.org> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
- 29 10月, 2005 1 次提交
-
-
由 Russell King 提交于
In PM v1, all devices were called at SUSPEND_DISABLE level. Then all devices were called at SUSPEND_SAVE_STATE level, and finally SUSPEND_POWER_DOWN level. However, with PM v2, to maintain compatibility for platform devices, I arranged for the PM v2 suspend/resume callbacks to call the old PM v1 suspend/resume callbacks three times with each level in order so that existing drivers continued to work. Since this is obsolete infrastructure which is no longer necessary, we can remove it. Here's an (untested) patch to do exactly that. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 06 9月, 2005 1 次提交
-
-
由 Peter Chubb 提交于
When building with CONFIG_PHYLIB=y on Itanium, I see: `mdio_bus_exit' referenced in section `.init.text' of drivers/built-in.o: defined in discarded section `.exit.text' of drivers/built-in.o I believe that mdio_bus_exit should not be declared __exit, because it is referencesd from __init sections in, say, phy_init(). Signed-off-by: NPeter Chubb <peterc@gelato.unsw.edu.au> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
- 05 9月, 2005 1 次提交
-
-
由 Pavel Machek 提交于
Fix remaining bits of u32 vs. pm_message confusion. Should not break anything. Signed-off-by: NPavel Machek <pavel@suse.cz> Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 29 8月, 2005 1 次提交
-
-
由 Andy Fleming 提交于
This patch adds back the code that was taken out, thus re-enabling: * The PHY Layer to initialize without crashing * Drivers to actually connect to PHYs * The entire PHY Control Layer This patch is used by the gianfar driver, and other drivers which are in development. Signed-off-by: NAndy Fleming <afleming@freescale.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
- 11 8月, 2005 2 次提交
-
-
由 Jeff Garzik 提交于
- unexport symbols never used outside of home module - remove dead code - remove CONFIG_PHYCONTROL, make it unconditionally enabled
-
由 Jeff Garzik 提交于
Includes fixes for problems noted by Adrian Bunk, Andrew Morton, and one other person lost in the annals of history (and email folders).
-
- 31 7月, 2005 1 次提交
-
-
由 Andy Fleming 提交于
ethernet drivers to remain as ignorant as is reasonable of the connected PHY's design and operation details. Signed-off-by: NAndy Fleming <afleming@freescale.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-