Prevent invalid pointer dereference on error path.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

In some cases fimc H/W did not stop although there were no output
buffers available. So the capture deactivation interrupt routine
is modified and the state of ST_CAPT_RUN is cleared only
in the LAST-IRQ call.

After LAST-IRQ is generated, H/W pointer will be skipped by 1 frame.
(reference by user manual) So, S/W pointer should be increased too.

Reviewed-by Jonghun Han <jonghun.han@samsung.com>
Signed-off-by: NSungchun Kang <sungchun.kang@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

When is called fimc_stop_capture, it seems that wait_event_timeout
used improperly. It should be wake up by irq handler.

Reviewed-by Jonghun Han <jonghun.han@samsung.com>
Signed-off-by: NSungchun Kang <sungchun.kang@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Horizontal and vertical scaling range are according to the following equations.
If (SRC_Width >= 64 x DST_Width) { Exit(-1);  /* Out of Horizontal scale range}
If (SRC_Height >= 64 x DST_Height) { Exit(-1);  /* Out of Vertical scale range}

fimc_check_scaler_ratio() is used to check if horizontal and vertical
scale range are valid or not. To use fimc_check_scaler_ratio,
source and destination format should be set by VIDIOC_S_FMT.
And in case of scaling up, it doesn't have to check the scale range.
Reviewed-by: NJonghun Han <jonghun.han@samsung.com>
Signed-off-by: NHyunwoong Kim <khw0178.kim@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The main scaler has four SFRs for main scaler ratio depending on FIMC version.
FIMC 4.x has only two SFRs and FIMC 5.x has four SFRs for main scaler.
Those are MainHorRatio, MainHorRatio_ext, MainVerRatio and MainverRatio_ext.

The FIMC 5.x has 15 bit resolution for scaling ratio as below.
{MainHorRatio,MainHorRatio_ext} = {[14:6],[5:0]}.
{MainVerRatio,MainVerRatio_ext} = {[14:6],[5:0]}.
MainHorRatio = CISCCTRL[24:16], MainHorRatio_ext = CIEXTEN[15:10]
MainVerRatio = CISCCTRL[8:0],   MainVerRatio_ext = CIEXTEN[5:0]

This patch supports FIMC 4.x and FIMC 5.x using platform_device_id::driver_data.
Reviewed-by: NJonghun Han <jonghun.han@samsung.com>
Signed-off-by: NHyunwoong Kim <khw0178.kim@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Manage the camera sensor clock in the host driver rather than
leaving this task for sensor drivers. The clock frequency
must be passed in the sensor's and host driver's platform data.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Prevent VIDIOC_STREAMON failing when s_stream callback is
not implemented by a sensor subdev driver.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Change s3c_fimc.h header file name to s5p_fimc.h, replace s3c_fimc_*
names with s5p_fimc_*. s3c_fimc need to be reserved for S3C series
and s5p-fimc driver will not cover CAMIF devices in S3C SoC series.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Conversion to multiplanar color formats and minor cleanup.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Porting to videobuf 2 and minor cleanup.
Separate videobuf_queue_ops are are created for m2m
and capture video nodes.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

FIMC IP in S5Pv310 series has extended DMA status registers
and some bit fields are marked as reserved comparing to S5PC100/110.
Use correct registers for getting DMA write pointer in each SoC variant
supported by the driver.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Create separate vidioc_g_crop/vidioc_s_crop handlers for capture
video node and so image cropping parameters are properly queried
at FIMC input (image sensor) and not at FIMC output.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Adapt to recent videobuf_queue_dma_contig_init signature change.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The argument isn't used anymore by the functions, remove it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, replace the hardcoded module name passed to those
functions by NULL in the cafe-ccic, via-camera and s5p-fimc drivers.

All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the drivers
modified here use.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add a video device driver per each FIMC entity to support
the camera capture input mode. Video capture node is registered
only if CCD sensor data is provided through driver's platfrom data
and board setup code.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>