Add blkcnt_t as the type of inode.i_blocks.  This enables you to make the size
of blkcnt_t either 4 bytes or 8 bytes on 32 bits architecture with CONFIG_LSF.

- CONFIG_LSF
  Add new configuration parameter.
- blkcnt_t
  On h8300, i386, mips, powerpc, s390 and sh that define sector_t,
  blkcnt_t is defined as u64 if CONFIG_LSF is enabled; otherwise it is
  defined as unsigned long.
  On other architectures, it is defined as unsigned long.
- inode.i_blocks
  Change the type from sector_t to blkcnt_t.
Signed-off-by: NTakashi Sato <sho@tnes.nec.co.jp>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch series fixes the following problems on 32 bits architecture.

o stat64 returns the lower 32 bits of blocks, although userland st_blocks
  has 64 bits, because i_blocks has only 32 bits.  The ioctl with FIOQSIZE has
  the same problem.

o As Dave Kleikamp said, making >2TB file on JFS results in writing an
  invalid block number to disk inode.  The cause is the same as above too.

o In generic quota code dquot_transfer(), the file usage is calculated from
  i_blocks via inode_get_bytes().  If the file is over 2TB, the change of
  usage is less than expected.  The cause is the same as above too.

o As Trond Myklebust said, statfs64's entries related to blocks are invalid
  on statfs64 for a network filesystem which has more than 2^32-1 blocks with
  CONFIG_LBD disabled.  [PATCH 3/3]

We made patches to fix problems that occur when handling a large filesystem
and a large file.  It was discussed on the mails titled "stat64 for over 2TB
file returned invalid st_blocks".
Signed-off-by: NTakashi Sato <sho@tnes.nec.co.jp>
Cc: Dave Kleikamp <shaggy@austin.ibm.com>
Cc: Jan Kara <jack@ucw.cz>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Modify well over a dozen mempool users to call mempool_create_slab_pool()
rather than calling mempool_create() with extra arguments, saving about 30
lines of code and increasing readability.
Signed-off-by: NMatthew Dobson <colpatch@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Create a simple wrapper function for the common case of creating a slab-based
mempool.
Signed-off-by: NMatthew Dobson <colpatch@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch changes a mempool user, which is basically just a wrapper around
kzalloc(), to use the common mempool_kmalloc/kfree, rather than its own
wrapper function, removing duplicated code.
Signed-off-by: NMatthew Dobson <colpatch@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add another allocator to the common mempool code: a kzalloc/kfree allocator

This will be used by the next patch in the series to replace a mempool-backed
kzalloc allocator.  It is also very likely that there will be more users in
the future.
Signed-off-by: NMatthew Dobson <colpatch@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch changes several mempool users, all of which are basically just
wrappers around kmalloc(), to use the common mempool_kmalloc/kfree, rather
than their own wrapper function, removing a bunch of duplicated code.
Signed-off-by: NMatthew Dobson <colpatch@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add another allocator to the common mempool code: a kmalloc/kfree allocator

This will be used by the next patch in the series to replace duplicate
mempool-backed kmalloc allocators in several places in the kernel.  It is also
very likely that there will be more users in the future.
Signed-off-by: NMatthew Dobson <colpatch@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Convert two mempool users that currently use their own mempool-backed page
allocators to use the generic mempool page allocator.

Also included are 2 trivial whitespace fixes.
Signed-off-by: NMatthew Dobson <colpatch@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This will be used by the next patch in the series to replace duplicate
mempool-backed page allocators in 2 places in the kernel.  It is also likely
that there will be more users in the future.
Signed-off-by: NMatthew Dobson <colpatch@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Update driver documentation.
Signed-off-by: NSteffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Remove some whitespaces and codingstyle issues.
Signed-off-by: NSteffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Remove per-driver versioning.
Signed-off-by: NSteffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Use ethtool_op_get_link instead of vortex_get_link.
Signed-off-by: NSteffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Handle netif_carrier_{on,of} also if media is forced to 10baseT/100baseTx.
Signed-off-by: NSteffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Set the polling interval for media changes to 5 seconds if link is down and
60 seconds if link is up.
Signed-off-by: NSteffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Check for media changes and netif_carrier by using mii_check_media() if mii is
used.
Signed-off-by: NSteffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

I noticed that after boot with an initrd in 2.6.16 the rootfs had:

--w-r-xr-T    1 root     root      6241141 Jan  1  1970 initrd.image

Which is caused by a small typo:
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix compilation for sound/oss/vwsnd.o, by moving li_destroy() above
li_create()

sound/oss/vwsnd.c:275: warning: conflicting types for ‘li_destroy’
sound/oss/vwsnd.c:275: error: static declaration of ‘li_destroy’ follows non-static declaration
sound/oss/vwsnd.c:264: error: previous implicit declaration of ‘li_destroy’ was here
Signed-off-by: NEric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Zdenek Pavlas <pavlas@nextra.cz>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The isicom driver uses request_firmware() and thus needs to select
FW_LOADER.
Signed-off-by: Nmaximilian attems <maks@sternwelten.at>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Coverity found an over-run @ line 364 of efi.c

This is due to the loop checking the size correctly, then adding a '\0'
after possibly hitting the end of the array.

Ensure the loop exits with one space left in the array.
Signed-off-by: NDarren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

drivers/input/touchscreen/ads7846.c: In function `ads7846_read12_ser':
drivers/input/touchscreen/ads7846.c:207: warning: implicit declaration of function `disable_irq'
drivers/input/touchscreen/ads7846.c:209: warning: implicit declaration of function `enable_irq'

Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Since the addition of boot_cpu_init(), fixup_cpu_present_map() has been a
no-op.  That's because fixup_cpu_present_map() won't touch cpu_present_map if
it has any bits set, and boot_cpu_init() sets a bit.

So remove fixup_cpu_present_map().

A consequence of this (actually of the boot_cpu_init() change) is that the
architecture _must_ populate cpu_present_map itself (probably in
smp_prepare_cpus()).  fixup_cpu_present_map() won't do it any more.

If the architecture doesn't do this, it'll only bring up a single CPU.

The other side effect (though less serious) is that smp_prepare_boot_cpu() no
longer needs to mark the boot cpu in the online and present maps -
boot_cpu_init() does that for everyone (to make early printks work).
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

tlclk calls register_chrdev() and permits register_chrdev() to allocate the
major, but it promptly forgets what that major was.  So if there's no hardware
present you still get "telco_clock" appearing in /proc/devices and, I assume,
an oops reading /proc/devices if tlclk was a module.

Fix.

Mark, I'd suggest that that we not call register_chrdev() until _after_ we've
established that the hardware is present.

Cc: Mark Gross <mgross@linux.intel.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Check that kernel_thread() succeeded, so we don't wait for something which
cannot happen.
Signed-off-by: NHerbert Poetzl <herbert@13thfloor.at>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Change proc_dir_entry->size to be loff_t to represent files like
/proc/vmcore for 32bit systems with more than 4G memory.

Needed for seeing correct size for /proc/vmcore for 32-bit systems with >
4G RAM.
Signed-off-by: NManeesh Soni <maneesh@in.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Create compat_sys_adjtimex and use it an all appropriate places.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

We had a copy of the compatibility version of struct timex in each 64 bit
architecture.  This patch just creates a global one and replaces all the
usages of the old ones.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: NKyle McMartin <kyle@parisc-linux.org>
Acked-by: NTony Luck <tony.luck@intel.com>
Acked-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Update the NFSv4 server to use the new posix_lock_file_conf() interface.
Remove unnecessary (and race-prone) posix_test_file() calls.
Signed-off-by: NAndy Adamson <andros@citi.umich.edu>
Signed-off-by: NJ. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Lockd and the NFSv4 server both exercise a race condition where
posix_test_lock() is called either before or after posix_lock_file() to
deal with a denied lock request due to a conflicting lock.

Remove the race condition for the NFSv4 server by adding a new conflicting
lock parameter to __posix_lock_file() , changing the name to
__posix_lock_file_conf().

Keep posix_lock_file() interface, add posix_lock_conf() interface, both
call __posix_lock_file_conf().

[akpm@osdl.org: Put the EXPORT_SYMBOL() where it belongs]
Signed-off-by: NAndy Adamson <andros@citi.umich.edu>
Signed-off-by: NJ. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

BUG instead of handling a case that should never happen.
Signed-off-by: NJ. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

I discovered on oprofile hunting on a SMP platform that dentry lookups were
slowed down because d_hash_mask, d_hash_shift and dentry_hashtable were in
a cache line that contained inodes_stat.  So each time inodes_stats is
changed by a cpu, other cpus have to refill their cache line.

This patch moves some variables to the __read_mostly section, in order to
avoid false sharing.  RCU dentry lookups can go full speed.
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add __KERNEL__ block.
Use __KERNEL__ to allow ioctl interface to be usable.
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Need to increment the version number because of the new PCI and sysfs
capabilities of the driver.  People maintaining things for distros have
asked that I do this after interface or major functional changes.
Signed-off-by: NCorey Minyard <minyard@acm.org>
Acked-by: NMatt Domsch <Matt_Domsch@dell.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add full driver model support for the IPMI driver.  It links in the proper
bus and device support.

It adds an "ipmi" driver interface that has each BMC discovered by the
driver (as a device).  These BMCs appear in the devices/platform directory.
 If there are multiple interfaces to the same BMC, the driver should
discover this and will only have one BMC entry.  The BMC entry will have
pointers to each interface device that connects to it.

The device information (statistics and config information) has not yet been
ported over to the driver model from proc, that will come later.

This work was based on work by Yani Ioannou.  I basically rewrote it using
that code as a guide, but he still deserves credit :).

[bunk@stusta.de: make ipmi_find_bmc_guid() static]
Signed-off-by: NCorey Minyard <minyard@acm.org>
Signed-off-by: NYani Ioannou <yani.ioannou@gmail.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Modify the PCI hanling code for the IPMI driver to use the new method of
tables and registering, and adds more generic PCI handling for IPMI.
Unfortunately, this required a rather large rework of the way the driver
did detection so it would be more event-driven.

[bunk@stusta.de: make a struct static]
Signed-off-by: NCorey Minyard <minyard@acm.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

net/core/flow.c: In function 'flow_cache_flush':
net/core/flow.c:299: warning: statement with no effect
Signed-off-by: NCon Kolivas <kernel@kolivas.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The return value of this function is never used, so let's be honest and
declare it as void.

Some places where invalidatepage returned 0, I have inserted comments
suggesting a BUG_ON.

[akpm@osdl.org: JBD BUG fix]
[akpm@osdl.org: rework for git-nfs]
[akpm@osdl.org: don't go BUG in block_invalidate_page()]
Signed-off-by: NNeil Brown <neilb@suse.de>
Acked-by: NDave Kleikamp <shaggy@austin.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The only user ignores the return value, and the only instanace
(block_sync_page) always returns 0...
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>