Enable CONFIG_SYSCON_REBOOT_MODE
Signed-off-by: NGuodong Xu <guodong.xu@linaro.org>
Signed-off-by: NWei Xu <xuwei5@hisilicon.com>

Enable configs for hi6421v530 mfd and regulator driver
 + CONFIG_MFD_HI6421_PMIC=y
 + CONFIG_REGULATOR_HI6421V530=y
Signed-off-by: NGuodong Xu <guodong.xu@linaro.org>
Signed-off-by: NWei Xu <xuwei5@hisilicon.com>

Enable HiSilicon Kirin series SoCs PCIe controllers
Signed-off-by: NGuodong Xu <guodong.xu@linaro.org>
Signed-off-by: NXiaowei Song <songxiaowei@hisilicon.com>
Signed-off-by: NWei Xu <xuwei5@hisilicon.com>

Enable HiSilicon SAS controller based on PCI device,
which is included in hip08 SoC.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NWei Xu <xuwei5@hisilicon.com>

The arch uses a verbatim copy of the asm-generic version and does not
add any own implementations to the header, so use asm-generic/fb.h
instead of duplicating code.

Link: http://lkml.kernel.org/r/20170517083545.2115-1-tklauser@distanz.chSigned-off-by: NTobias Klauser <tklauser@distanz.ch>
Acked-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Hyper-V identifies vCPUs by Virtual Processor Index, which can be
queried via HV_X64_MSR_VP_INDEX msr.  It is defined by the spec as a
sequential number which can't exceed the maximum number of vCPUs per VM.
APIC ids can be sparse and thus aren't a valid replacement for VP
indices.

Current KVM uses its internal vcpu index as VP_INDEX.  However, to make
it predictable and persistent across VM migrations, the userspace has to
control the value of VP_INDEX.

This patch achieves that, by storing vp_index explicitly on vcpu, and
allowing HV_X64_MSR_VP_INDEX to be set from the host side.  For
compatibility it's initialized to KVM vcpu index.  Also a few variables
are renamed to make clear distinction betweed this Hyper-V vp_index and
KVM vcpu_id (== APIC id).  Besides, a new capability,
KVM_CAP_HYPERV_VP_INDEX, is added to allow the userspace to skip
attempting msr writes where unsupported, to avoid spamming error logs.
Signed-off-by: NRoman Kagan <rkagan@virtuozzo.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

Adds another flag bit (bit 2) to MSR_KVM_ASYNC_PF_EN. If bit 2 is 1,
async page faults are delivered to L1 as #PF vmexits; if bit 2 is 0,
kvm_can_do_async_pf returns 0 if in guest mode.

This is similar to what svm.c wanted to do all along, but it is only
enabled for Linux as L1 hypervisor.  Foreign hypervisors must never
receive async page faults as vmexits, because they'd probably be very
confused about that.

Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NWanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

Add an nested_apf field to vcpu->arch.exception to identify an async page
fault, and constructs the expected vm-exit information fields. Force a
nested VM exit from nested_vmx_check_exception() if the injected #PF is
async page fault.

Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NWanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

This patch adds the L1 guest async page fault #PF vmexit handler, such
by L1 similar to ordinary async page fault.

Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NWanpeng Li <wanpeng.li@hotmail.com>
[Passed insn parameters to kvm_mmu_page_fault().]
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

This patch removes all arguments except the first in
kvm_x86_ops->queue_exception since they can extract the arguments from
vcpu->arch.exception themselves.

Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NWanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

There is a flaw in the Hyper-V SynIC implementation in KVM: when message
page or event flags page is enabled by setting the corresponding msr,
KVM zeroes it out.  This is problematic because on migration the
corresponding MSRs are loaded on the destination, so the content of
those pages is lost.

This went unnoticed so far because the only user of those pages was
in-KVM hyperv synic timers, which could continue working despite that
zeroing.

Newer QEMU uses those pages for Hyper-V VMBus implementation, and
zeroing them breaks the migration.

Besides, in newer QEMU the content of those pages is fully managed by
QEMU, so zeroing them is undesirable even when writing the MSRs from the
guest side.

To support this new scheme, introduce a new capability,
KVM_CAP_HYPERV_SYNIC2, which, when enabled, makes sure that the synic
pages aren't zeroed out in KVM.
Signed-off-by: NRoman Kagan <rkagan@virtuozzo.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

The backwards_tsc_observed global introduced in commit 16a96021 is never
reset to false. If a VM happens to be running while the host is suspended
(a common source of the TSC jumping backwards), master clock will never
be enabled again for any VM. In contrast, if no VM is running while the
host is suspended, master clock is unaffected. This is inconsistent and
unnecessarily strict. Let's track the backwards_tsc_observed variable
separately and let each VM start with a clean slate.

Real world impact: My Windows VMs get slower after my laptop undergoes a
suspend/resume cycle. The only way to get the perf back is unloading and
reloading the kvm module.
Signed-off-by: NLadi Prosek <lprosek@redhat.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

Make the code like the rest of the kernel.

Link: http://lkml.kernel.org/r/1cd3d401626e51ea0e2333a860e76e80bc560a4c.1499284835.git.joe@perches.comSigned-off-by: NJoe Perches <joe@perches.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make the code like the rest of the kernel.

Link: http://lkml.kernel.org/r/f81bb2a67a97b1fd8b6ea99bd350d8a0f6864fb1.1499284835.git.joe@perches.comSigned-off-by: NJoe Perches <joe@perches.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make the code like the rest of the kernel.

Link: http://lkml.kernel.org/r/756d3fb543e981b9284e756fa27616725a354b28.1499284835.git.joe@perches.comSigned-off-by: NJoe Perches <joe@perches.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make the code like the rest of the kernel.

Link: http://lkml.kernel.org/r/14db9c166d5b68efa77e337cfe49bb9b29bca3f7.1499284835.git.joe@perches.comSigned-off-by: NJoe Perches <joe@perches.com>
Acked-by: NGreg Ungerer <gerg@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make the use of inline like the rest of the kernel.

Link: http://lkml.kernel.org/r/f42b2202bd0d4e7ccf79ce5348bb255a035e67bb.1499284835.git.joe@perches.comSigned-off-by: NJoe Perches <joe@perches.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make the use of inline like the rest of the kernel.

Link: http://lkml.kernel.org/r/d47074493af80ce12590340294bc49618165c30d.1499284835.git.joe@perches.comSigned-off-by: NJoe Perches <joe@perches.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make the use of asmlinkage like the rest of the kernel.

Link: http://lkml.kernel.org/r/efb2dfed4d9315bf68ec0334c81b65af176a0174.1499284835.git.joe@perches.comSigned-off-by: NJoe Perches <joe@perches.com>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move inline to be like the rest of the kernel.

Link: http://lkml.kernel.org/r/6bf1bec049897c4158f698b866810f47c728f233.1499284835.git.joe@perches.comSigned-off-by: NJoe Perches <joe@perches.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Convert 'u8 inline' to 'inline u8' to be the same style used by the rest
of the kernel.

Miscellanea:

jornada_ssp_reverse is an odd function.
It is declared inline but is also EXPORT_SYMBOL.
It is also apparently only used by jornada720_ssp.c
Likely the EXPORT_SYMBOL could be removed and the function
converted to static.

The addition of static and removal of EXPORT_SYMBOL was not done.

Link: http://lkml.kernel.org/r/5bd3b2bf39c6c9caf773949f18158f8f5ec08582.1499284835.git.joe@perches.comSigned-off-by: NJoe Perches <joe@perches.com>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

asmlinkage is either 'extern "C"' or blank.

Move the uses of asmlinkage before the return types to be similar
to the rest of the kernel.

Link: http://lkml.kernel.org/r/005b8e120650c6a13b541e420f4e3605603fe9e6.1499284835.git.joe@perches.comSigned-off-by: NJoe Perches <joe@perches.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krcmar <rkrcmar@redhat.com>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__GFP_REPEAT was designed to allow retry-but-eventually-fail semantic to
the page allocator.  This has been true but only for allocations
requests larger than PAGE_ALLOC_COSTLY_ORDER.  It has been always
ignored for smaller sizes.  This is a bit unfortunate because there is
no way to express the same semantic for those requests and they are
considered too important to fail so they might end up looping in the
page allocator for ever, similarly to GFP_NOFAIL requests.

Now that the whole tree has been cleaned up and accidental or misled
usage of __GFP_REPEAT flag has been removed for !costly requests we can
give the original flag a better name and more importantly a more useful
semantic.  Let's rename it to __GFP_RETRY_MAYFAIL which tells the user
that the allocator would try really hard but there is no promise of a
success.  This will work independent of the order and overrides the
default allocator behavior.  Page allocator users have several levels of
guarantee vs.  cost options (take GFP_KERNEL as an example)

 - GFP_KERNEL & ~__GFP_RECLAIM - optimistic allocation without _any_
   attempt to free memory at all. The most light weight mode which even
   doesn't kick the background reclaim. Should be used carefully because
   it might deplete the memory and the next user might hit the more
   aggressive reclaim

 - GFP_KERNEL & ~__GFP_DIRECT_RECLAIM (or GFP_NOWAIT)- optimistic
   allocation without any attempt to free memory from the current
   context but can wake kswapd to reclaim memory if the zone is below
   the low watermark. Can be used from either atomic contexts or when
   the request is a performance optimization and there is another
   fallback for a slow path.

 - (GFP_KERNEL|__GFP_HIGH) & ~__GFP_DIRECT_RECLAIM (aka GFP_ATOMIC) -
   non sleeping allocation with an expensive fallback so it can access
   some portion of memory reserves. Usually used from interrupt/bh
   context with an expensive slow path fallback.

 - GFP_KERNEL - both background and direct reclaim are allowed and the
   _default_ page allocator behavior is used. That means that !costly
   allocation requests are basically nofail but there is no guarantee of
   that behavior so failures have to be checked properly by callers
   (e.g. OOM killer victim is allowed to fail currently).

 - GFP_KERNEL | __GFP_NORETRY - overrides the default allocator behavior
   and all allocation requests fail early rather than cause disruptive
   reclaim (one round of reclaim in this implementation). The OOM killer
   is not invoked.

 - GFP_KERNEL | __GFP_RETRY_MAYFAIL - overrides the default allocator
   behavior and all allocation requests try really hard. The request
   will fail if the reclaim cannot make any progress. The OOM killer
   won't be triggered.

 - GFP_KERNEL | __GFP_NOFAIL - overrides the default allocator behavior
   and all allocation requests will loop endlessly until they succeed.
   This might be really dangerous especially for larger orders.

Existing users of __GFP_REPEAT are changed to __GFP_RETRY_MAYFAIL
because they already had their semantic.  No new users are added.
__alloc_pages_slowpath is changed to bail out for __GFP_RETRY_MAYFAIL if
there is no progress and we have already passed the OOM point.

This means that all the reclaim opportunities have been exhausted except
the most disruptive one (the OOM killer) and a user defined fallback
behavior is more sensible than keep retrying in the page allocator.

[akpm@linux-foundation.org: fix arch/sparc/kernel/mdesc.c]
[mhocko@suse.com: semantic fix]
  Link: http://lkml.kernel.org/r/20170626123847.GM11534@dhcp22.suse.cz
[mhocko@kernel.org: address other thing spotted by Vlastimil]
  Link: http://lkml.kernel.org/r/20170626124233.GN11534@dhcp22.suse.cz
Link: http://lkml.kernel.org/r/20170623085345.11304-3-mhocko@kernel.orgSigned-off-by: NMichal Hocko <mhocko@suse.com>
Acked-by: NVlastimil Babka <vbabka@suse.cz>
Cc: Alex Belits <alex.belits@cavium.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: NeilBrown <neilb@suse.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Patch series "mm: give __GFP_REPEAT a better semantic".

The main motivation for the change is that the current implementation of
__GFP_REPEAT is not very much useful.

The documentation says:
 * __GFP_REPEAT: Try hard to allocate the memory, but the allocation attempt
 *   _might_ fail.  This depends upon the particular VM implementation.

It just fails to mention that this is true only for large (costly) high
order which has been the case since the flag was introduced.  A similar
semantic would be really helpful for smal orders as well, though,
because we have places where a failure with a specific fallback error
handling is preferred to a potential endless loop inside the page
allocator.

The earlier cleanup dropped __GFP_REPEAT usage for low (!costly) order
users so only those which might use larger orders have stayed.  One new
user added in the meantime is addressed in patch 1.

Let's rename the flag to something more verbose and use it for existing
users.  Semantic for those will not change.  Then implement low
(!costly) orders failure path which is hit after the page allocator is
about to invoke the oom killer.  With that we have a good counterpart
for __GFP_NORETRY and finally can tell try as hard as possible without
the OOM killer.

Xfs code already has an existing annotation for allocations which are
allowed to fail and we can trivially map them to the new gfp flag
because it will provide the semantic KM_MAYFAIL wants.  Christoph didn't
consider the new flag really necessary but didn't respond to the OOM
killer aspect of the change so I have kept the patch.  If this is still
seen as not really needed I can drop the patch.

kvmalloc will allow also !costly high order allocations to retry hard
before falling back to the vmalloc.

drm/i915 asked for the new semantic explicitly.

Memory migration code, especially for the memory hotplug, should back
off rather than invoking the OOM killer as well.

This patch (of 6):

Commit 3377e227 ("MIPS: Add 48-bit VA space (and 4-level page
tables) for 4K pages.") has added a new __GFP_REPEAT user but using this
flag doesn't really make any sense for order-0 request which is the case
here because PUD_ORDER is 0.  __GFP_REPEAT has historically effect only
on allocation requests with order > PAGE_ALLOC_COSTLY_ORDER.

This doesn't introduce any functional change.  This is a preparatory
patch for later work which renames the flag and redefines its semantic.

Link: http://lkml.kernel.org/r/20170623085345.11304-2-mhocko@kernel.orgSigned-off-by: NMichal Hocko <mhocko@suse.com>
Acked-by: NVlastimil Babka <vbabka@suse.cz>
Cc: Alex Belits <alex.belits@cavium.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: NeilBrown <neilb@suse.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When RLIMIT_STACK is, for example, 256MB, the current code results in a
gap between the top of the task and mmap_base of 256MB, failing to take
into account the amount by which the stack address was randomized.  In
other words, the stack gets less than RLIMIT_STACK space.

Ensure that the gap between the stack and mmap_base always takes stack
randomization and the stack guard gap into account.

Inspired by Daniel Micay's linux-hardened tree.

Link: http://lkml.kernel.org/r/20170622200033.25714-4-riel@redhat.comSigned-off-by: NRik van Riel <riel@redhat.com>
Reported-by: NFlorian Weimer <fweimer@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Daniel Micay <danielmicay@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When RLIMIT_STACK is, for example, 256MB, the current code results in a
gap between the top of the task and mmap_base of 256MB, failing to take
into account the amount by which the stack address was randomized.  In
other words, the stack gets less than RLIMIT_STACK space.

Ensure that the gap between the stack and mmap_base always takes stack
randomization and the stack guard gap into account.

Obtained from Daniel Micay's linux-hardened tree.

Link: http://lkml.kernel.org/r/20170622200033.25714-3-riel@redhat.comSigned-off-by: NDaniel Micay <danielmicay@gmail.com>
Signed-off-by: NRik van Riel <riel@redhat.com>
Reported-by: NFlorian Weimer <fweimer@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Daniel Micay <danielmicay@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When RLIMIT_STACK is, for example, 256MB, the current code results in a
gap between the top of the task and mmap_base of 256MB, failing to take
into account the amount by which the stack address was randomized.  In
other words, the stack gets less than RLIMIT_STACK space.

Ensure that the gap between the stack and mmap_base always takes stack
randomization and the stack guard gap into account.

Obtained from Daniel Micay's linux-hardened tree.

Link: http://lkml.kernel.org/r/20170622200033.25714-2-riel@redhat.comSigned-off-by: NDaniel Micay <danielmicay@gmail.com>
Signed-off-by: NRik van Riel <riel@redhat.com>
Reported-by: NFlorian Weimer <fweimer@redhat.com>
Acked-by: NIngo Molnar <mingo@kernel.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Daniel Micay <danielmicay@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use the ascii-armor canary to prevent unterminated C string overflows
from being able to successfully overwrite the canary, even if they
somehow obtain the canary value.

Inspired by execshield ascii-armor and Daniel Micay's linux-hardened
tree.

Link: http://lkml.kernel.org/r/20170524123446.78510066@annuminas.surriel.comSigned-off-by: NRik van Riel <riel@redhat.com>
Acked-by: NKees Cook <keescook@chromium.org>
Cc: Daniel Micay <danielmicay@gmail.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use the ascii-armor canary to prevent unterminated C string overflows
from being able to successfully overwrite the canary, even if they
somehow obtain the canary value.

Inspired by execshield ascii-armor and Daniel Micay's linux-hardened
tree.

Link: http://lkml.kernel.org/r/20170524155751.424-5-riel@redhat.comSigned-off-by: NRik van Riel <riel@redhat.com>
Acked-by: NKees Cook <keescook@chromium.org>
Cc: Daniel Micay <danielmicay@gmail.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use the ascii-armor canary to prevent unterminated C string overflows
from being able to successfully overwrite the canary, even if they
somehow obtain the canary value.

Inspired by execshield ascii-armor and Daniel Micay's linux-hardened
tree.

Link: http://lkml.kernel.org/r/20170524155751.424-4-riel@redhat.comSigned-off-by: NRik van Riel <riel@redhat.com>
Acked-by: NKees Cook <keescook@chromium.org>
Cc: Daniel Micay <danielmicay@gmail.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When building the sh architecture, the compiler doesn't realize that
BUG() doesn't return, so it will complain about functions using BUG()
that are marked with the noreturn attribute:

   lib/string.c: In function 'fortify_panic':
>> lib/string.c:986:1: warning: 'noreturn' function does return
    }
    ^

Link: http://lkml.kernel.org/r/20170627192050.GA66784@beastSigned-off-by: NKees Cook <keescook@chromium.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: Daniel Micay <danielmicay@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds support for compiling with a rough equivalent to the glibc
_FORTIFY_SOURCE=1 feature, providing compile-time and runtime buffer
overflow checks for string.h functions when the compiler determines the
size of the source or destination buffer at compile-time.  Unlike glibc,
it covers buffer reads in addition to writes.

GNU C __builtin_*_chk intrinsics are avoided because they would force a
much more complex implementation.  They aren't designed to detect read
overflows and offer no real benefit when using an implementation based
on inline checks.  Inline checks don't add up to much code size and
allow full use of the regular string intrinsics while avoiding the need
for a bunch of _chk functions and per-arch assembly to avoid wrapper
overhead.

This detects various overflows at compile-time in various drivers and
some non-x86 core kernel code.  There will likely be issues caught in
regular use at runtime too.

Future improvements left out of initial implementation for simplicity,
as it's all quite optional and can be done incrementally:

* Some of the fortified string functions (strncpy, strcat), don't yet
  place a limit on reads from the source based on __builtin_object_size of
  the source buffer.

* Extending coverage to more string functions like strlcat.

* It should be possible to optionally use __builtin_object_size(x, 1) for
  some functions (C strings) to detect intra-object overflows (like
  glibc's _FORTIFY_SOURCE=2), but for now this takes the conservative
  approach to avoid likely compatibility issues.

* The compile-time checks should be made available via a separate config
  option which can be enabled by default (or always enabled) once enough
  time has passed to get the issues it catches fixed.

Kees said:
 "This is great to have. While it was out-of-tree code, it would have
  blocked at least CVE-2016-3858 from being exploitable (improper size
  argument to strlcpy()). I've sent a number of fixes for
  out-of-bounds-reads that this detected upstream already"

[arnd@arndb.de: x86: fix fortified memcpy]
  Link: http://lkml.kernel.org/r/20170627150047.660360-1-arnd@arndb.de
[keescook@chromium.org: avoid panic() in favor of BUG()]
  Link: http://lkml.kernel.org/r/20170626235122.GA25261@beast
[keescook@chromium.org: move from -mm, add ARCH_HAS_FORTIFY_SOURCE, tweak Kconfig help]
Link: http://lkml.kernel.org/r/20170526095404.20439-1-danielmicay@gmail.com
Link: http://lkml.kernel.org/r/1497903987-21002-8-git-send-email-keescook@chromium.orgSigned-off-by: NDaniel Micay <danielmicay@gmail.com>
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NKees Cook <keescook@chromium.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Daniel Axtens <dja@axtens.net>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Testing the fortified string functions[1] would cause a kernel panic on
boot in test_feature_fixups() due to a buffer overflow in memcmp.

This boils down to things like this:

  extern unsigned int ftr_fixup_test1;
  extern unsigned int ftr_fixup_test1_orig;

  check(memcmp(&ftr_fixup_test1, &ftr_fixup_test1_orig, size) == 0);

We know that these are asm labels so it is safe to read up to 'size'
bytes at those addresses.

However, because we have passed the address of a single unsigned int to
memcmp, the compiler believes the underlying object is in fact a single
unsigned int.  So if size > sizeof(unsigned int), there will be a panic
at runtime.

We can fix this by changing the types: instead of calling the asm labels
unsigned ints, call them unsigned int[]s.  Therefore the size isn't
incorrectly determined at compile time and we get a regular unsafe
memcmp and no panic.

[1] http://openwall.com/lists/kernel-hardening/2017/05/09/2

Link: http://lkml.kernel.org/r/1497903987-21002-7-git-send-email-keescook@chromium.orgSigned-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NKees Cook <keescook@chromium.org>
Suggested-by: NMichael Ellerman <mpe@ellerman.id.au>
Tested-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Daniel Micay <danielmicay@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

prom_init is a bit special; in theory it should be able to be linked
separately to the kernel.  To keep this from getting too complex, the
symbols that prom_init.c uses are checked.

Fortification adds symbols, and it gets quite messy as it includes
things like panic().  So just don't fortify prom_init.c for now.

Link: http://lkml.kernel.org/r/1497903987-21002-6-git-send-email-keescook@chromium.orgSigned-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NKees Cook <keescook@chromium.org>
Acked-by: NMichael Ellerman <mpe@ellerman.id.au>
Cc: Daniel Micay <danielmicay@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Implement an arch-speicfic watchdog rather than use the perf-based
hardlockup detector.

The new watchdog takes the soft-NMI directly, rather than going through
perf.  Perf interrupts are to be made maskable in future, so that would
prevent the perf detector from working in those regions.

Additionally, implement a SMP based detector where all CPUs watch one
another by pinging a shared cpumask.  This is because powerpc Book3S
does not have a true periodic local NMI, but some platforms do implement
a true NMI IPI.

If a CPU is stuck with interrupts hard disabled, the soft-NMI watchdog
does not work, but the SMP watchdog will.  Even on platforms without a
true NMI IPI to get a good trace from the stuck CPU, other CPUs will
notice the lockup sufficiently to report it and panic.

[npiggin@gmail.com: honor watchdog disable at boot/hotplug]
  Link: http://lkml.kernel.org/r/20170621001346.5bb337c9@roar.ozlabs.ibm.com
[npiggin@gmail.com: fix false positive warning at CPU unplug]
  Link: http://lkml.kernel.org/r/20170630080740.20766-1-npiggin@gmail.com
[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/20170616065715.18390-6-npiggin@gmail.comSigned-off-by: NNicholas Piggin <npiggin@gmail.com>
Reviewed-by: NDon Zickus <dzickus@redhat.com>
Tested-by: Babu Moger <babu.moger@oracle.com>	[sparc]
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Split SOFTLOCKUP_DETECTOR from LOCKUP_DETECTOR, and split
HARDLOCKUP_DETECTOR_PERF from HARDLOCKUP_DETECTOR.

LOCKUP_DETECTOR implies the general boot, sysctl, and programming
interfaces for the lockup detectors.

An architecture that wants to use a hard lockup detector must define
HAVE_HARDLOCKUP_DETECTOR_PERF or HAVE_HARDLOCKUP_DETECTOR_ARCH.

Alternatively an arch can define HAVE_NMI_WATCHDOG, which provides the
minimum arch_touch_nmi_watchdog, and it otherwise does its own thing and
does not implement the LOCKUP_DETECTOR interfaces.

sparc is unusual in that it has started to implement some of the
interfaces, but not fully yet.  It should probably be converted to a full
HAVE_HARDLOCKUP_DETECTOR_ARCH.

[npiggin@gmail.com: fix]
  Link: http://lkml.kernel.org/r/20170617223522.66c0ad88@roar.ozlabs.ibm.com
Link: http://lkml.kernel.org/r/20170616065715.18390-4-npiggin@gmail.comSigned-off-by: NNicholas Piggin <npiggin@gmail.com>
Reviewed-by: NDon Zickus <dzickus@redhat.com>
Reviewed-by: NBabu Moger <babu.moger@oracle.com>
Tested-by: Babu Moger <babu.moger@oracle.com>	[sparc]
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

For architectures that define HAVE_NMI_WATCHDOG, instead of having them
provide the complete touch_nmi_watchdog() function, just have them
provide arch_touch_nmi_watchdog().

This gives the generic code more flexibility in implementing this
function, and arch implementations don't miss out on touching the
softlockup watchdog or other generic details.

Link: http://lkml.kernel.org/r/20170616065715.18390-3-npiggin@gmail.comSigned-off-by: NNicholas Piggin <npiggin@gmail.com>
Reviewed-by: NDon Zickus <dzickus@redhat.com>
Reviewed-by: NBabu Moger <babu.moger@oracle.com>
Tested-by: Babu Moger <babu.moger@oracle.com>	[sparc]
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

vmcoreinfo_max_size stands for the vmcoreinfo_data, the correct one we
should use is vmcoreinfo_note whose total size is VMCOREINFO_NOTE_SIZE.

Like explained in commit 77019967 ("kdump: fix exported size of
vmcoreinfo note"), it should not affect the actual function, but we
better fix it, also this change should be safe and backward compatible.

After this, we can get rid of variable vmcoreinfo_max_size, let's use
the corresponding macros directly, fewer variables means more safety for
vmcoreinfo operation.

[xlpang@redhat.com: fix build warning]
  Link: http://lkml.kernel.org/r/1494830606-27736-1-git-send-email-xlpang@redhat.com
Link: http://lkml.kernel.org/r/1493281021-20737-2-git-send-email-xlpang@redhat.comSigned-off-by: NXunlei Pang <xlpang@redhat.com>
Reviewed-by: NMahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Reviewed-by: NDave Young <dyoung@redhat.com>
Cc: Hari Bathini <hbathini@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

As Eric said,
 "what we need to do is move the variable vmcoreinfo_note out of the
  kernel's .bss section. And modify the code to regenerate and keep this
  information in something like the control page.

  Definitely something like this needs a page all to itself, and ideally
  far away from any other kernel data structures. I clearly was not
  watching closely the data someone decided to keep this silly thing in
  the kernel's .bss section."

This patch allocates extra pages for these vmcoreinfo_XXX variables, one
advantage is that it enhances some safety of vmcoreinfo, because
vmcoreinfo now is kept far away from other kernel data structures.

Link: http://lkml.kernel.org/r/1493281021-20737-1-git-send-email-xlpang@redhat.comSigned-off-by: NXunlei Pang <xlpang@redhat.com>
Tested-by: NMichael Holzheu <holzheu@linux.vnet.ibm.com>
Reviewed-by: NJuergen Gross <jgross@suse.com>
Suggested-by: NEric Biederman <ebiederm@xmission.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Young <dyoung@redhat.com>
Cc: Hari Bathini <hbathini@linux.vnet.ibm.com>
Cc: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Enable the Virtual VMLOAD VMSAVE feature. This is done by setting bit 1
at position B8h in the vmcb.

The processor must have nested paging enabled, be in 64-bit mode and
have support for the Virtual VMLOAD VMSAVE feature for the bit to be set
in the vmcb.
Signed-off-by: NJanakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>