[ Upstream commit 4e651bad848955d88b29a568bfbfb4b831270e16 ]

We do not currently clear wl->elp_compl on ELP timeout and we have bogus
lingering pointer that wlcore_irq then will try to access after recovery
is done:

BUG: spinlock bad magic on CPU#1, irq/255-wl12xx/580
...
(spin_dump) from [<c01b9344>] (do_raw_spin_lock+0xc8/0x124)
(do_raw_spin_lock) from [<c09b3970>] (_raw_spin_lock_irqsave+0x68/0x74)
(_raw_spin_lock_irqsave) from [<c01a02f0>] (complete+0x24/0x58)
(complete) from [<bf572610>] (wlcore_irq+0x48/0x17c [wlcore])
(wlcore_irq [wlcore]) from [<c01c5efc>] (irq_thread_fn+0x2c/0x64)
(irq_thread_fn) from [<c01c623c>] (irq_thread+0x148/0x290)
(irq_thread) from [<c016b4b0>] (kthread+0x160/0x17c)
(kthread) from [<c01010b4>] (ret_from_fork+0x14/0x20)
...

After that the system will hang. Let's fix this by adding a flag for
recovery and moving the recovery work call to to the error handling
section.

And we want to set WL1271_FLAG_INTENDED_FW_RECOVERY and actually clear
it too in wl1271_recovery_work() and just downgrade the error to a
warning to prevent overly verbose output.

Cc: Eyal Reizer <eyalr@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit d92116b800fb79a72ad26121f5011f6aa3ad94c2 ]

On OLPC XO-1, the RTC is discovered via device tree from the arch
initcall. Don't let the PC platform register another one from its device
initcall, it's not going to work:

  sysfs: cannot create duplicate filename '/devices/platform/rtc_cmos'
  CPU: 0 PID: 1 Comm: swapper Not tainted 4.19.0-rc6 #12
  Hardware name: OLPC XO/XO, BIOS OLPC Ver 1.00.01 06/11/2014
  Call Trace:
   dump_stack+0x16/0x18
   sysfs_warn_dup+0x46/0x58
   sysfs_create_dir_ns+0x76/0x9b
   kobject_add_internal+0xed/0x209
   ? __schedule+0x3fa/0x447
   kobject_add+0x5b/0x66
   device_add+0x298/0x535
   ? insert_resource_conflict+0x2a/0x3e
   platform_device_add+0x14d/0x192
   ? io_delay_init+0x19/0x19
   platform_device_register+0x1c/0x1f
   add_rtc_cmos+0x16/0x31
   do_one_initcall+0x78/0x14a
   ? do_early_param+0x75/0x75
   kernel_init_freeable+0x152/0x1e0
   ? rest_init+0xa2/0xa2
   kernel_init+0x8/0xd5
   ret_from_fork+0x2e/0x38
  kobject_add_internal failed for rtc_cmos with -EEXIST, don't try to
    register things with the same name in the same directory.
  platform rtc_cmos: registered platform RTC device (no PNP device found)
Signed-off-by: NLubomir Rintel <lkundrak@v3.sk>
Signed-off-by: NBorislav Petkov <bp@suse.de>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: Ingo Molnar <mingo@redhat.com>
CC: x86-ml <x86@kernel.org>
Link: http://lkml.kernel.org/r/20181004160808.307738-1-lkundrak@v3.skSigned-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 2e1976bb75263fbad918e82184b16a23bd721546 ]

When reading the profiles from the EWRD table in ACPI, we loop over
the data and set it into our internal table.  We use the number of
profiles specified in ACPI without checking its validity, so if the
ACPI table is corrupted and the number is larger than our array size,
we will try to make an out-of-bounds access.

Fix this by making sure the value specified in the ACPI table is
valid.

Fixes: 69964905 ("iwlwifi: mvm: add support for EWRD (Dynamic SAR) ACPI table")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 155f7e0441cd121b1e673d465a35e99f4b9b2f0b ]

Fix a bug that happens in the following scenario:
1) suspend without WoWLAN
2) mac80211 calls drv_stop because of the suspend
3) __iwl_mvm_mac_stop deallocates the aux station
4) during drv_stop the firmware crashes
5) iwlmvm:
	* sets IWL_MVM_STATUS_HW_RESTART_REQUESTED
	* asks mac80211 to kick the restart flow
6) mac80211 puts the restart worker into a freezable
   queue which means that the worker will not run for now
   since the workqueue is already frozen
7) ...
8) resume
9) mac80211 runs ieee80211_reconfig as part of the resume
10) mac80211 detects that a restart flow has been requested
    and that we are now resuming from suspend and cancels
    the restart worker
11) mac80211 calls drv_start()
12) __iwl_mvm_mac_start checks that IWL_MVM_STATUS_HW_RESTART_REQUESTED
    clears it, sets IWL_MVM_STATUS_IN_HW_RESTART and calls
    iwl_mvm_restart_cleanup()
13) iwl_fw_error_dump gets called and accesses the device
    to get debug data
14) iwl_mvm_up adds the aux station
15) iwl_mvm_add_aux_sta() allocates an internal station for
    the aux station
16) iwl_mvm_allocate_int_sta() tests IWL_MVM_STATUS_IN_HW_RESTART
    and doesn't really allocate a station ID for the aux
    station
17) a new queue is added for the aux station

Note that steps from 5 to 9 aren't really part of the
problem but were described for the sake of completeness.

Once the iwl_mvm_mac_stop() is called, the device is not
accessible, meaning that step 12) can't succeed and we'll
see the following:

drivers/net/wireless/intel/iwlwifi/pcie/trans.c:2122 iwl_trans_pcie_grab_nic_access+0xc0/0x1d6 [iwlwifi]()
Timeout waiting for hardware access (CSR_GP_CNTRL 0x080403d8)
Call Trace:
[<ffffffffc03e6ad3>] iwl_trans_pcie_grab_nic_access+0xc0/0x1d6 [iwlwifi]
[<ffffffffc03e6a13>] iwl_trans_pcie_dump_regs+0x3fd/0x3fd [iwlwifi]
[<ffffffffc03dad42>] iwl_fw_error_dump+0x4f5/0xe8b [iwlwifi]
[<ffffffffc04bd43e>] __iwl_mvm_mac_start+0x5a/0x21a [iwlmvm]
[<ffffffffc04bd6d2>] iwl_mvm_mac_start+0xd4/0x103 [iwlmvm]
[<ffffffffc042d378>] drv_start+0xa1/0xc5 [iwl7000_mac80211]
[<ffffffffc045a339>] ieee80211_reconfig+0x145/0xf50 [mac80211]
[<ffffffffc044788b>] ieee80211_resume+0x62/0x66 [mac80211]
[<ffffffffc0366c5b>] wiphy_resume+0xa9/0xc6 [cfg80211]

The station id of the aux station is set to 0xff in step 3
and because we don't really allocate a new station id for
the auxliary station (as explained in 16), we end up sending
a command to the firmware asking to connect the queue
to station id 0xff. This makes the firmware crash with the
following information:

0x00002093 | ADVANCED_SYSASSERT
0x000002F0 | trm_hw_status0
0x00000000 | trm_hw_status1
0x00000B38 | branchlink2
0x0001978C | interruptlink1
0x00000000 | interruptlink2
0xFF080501 | data1
0xDEADBEEF | data2
0xDEADBEEF | data3
Firmware error during reconfiguration - reprobe!
FW error in SYNC CMD SCD_QUEUE_CFG

Fix this by clearing IWL_MVM_STATUS_HW_RESTART_REQUESTED
in iwl_mvm_mac_stop(). We won't be able to collect debug
data anyway and when we will brought up again, we will
have a clean state from the firmware perspective.
Since we won't have IWL_MVM_STATUS_IN_HW_RESTART set in
step 12) we won't get to the 2093 ASSERT either.

Fixes: bf8b286f ("iwlwifi: mvm: defer setting IWL_MVM_STATUS_IN_HW_RESTART")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 868a1e863f95183f00809363fefba6d4f5bcd116 ]

If all free RB queues are empty, the driver will never restock the
free RB queue.  That's because the restocking happens in the Rx flow,
and if the free queue is empty there will be no Rx.

Although there's a background worker (a.k.a. allocator) allocating
memory for RBs so that the Rx handler can restock them, the worker may
run only after the free queue has become empty (and then it is too
late for restocking as explained above).

There is a solution for that called 'emergency': If the number of used
RB's reaches half the amount of all RB's, the Rx handler will not wait
for the allocator but immediately allocate memory for the used RB's
and restock the free queue.

But, since the used RB's is per queue, it may happen that the used
RB's are spread between the queues such that the emergency check will
fail for each of the queues
(and still run out of RBs, causing the above symptom).

To fix it, move to emergency mode if the sum of *all* used RBs (for
all Rx queues) reaches half the amount of all RB's
Signed-off-by: NShaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 0d55c668b218a1db68b5044bce4de74e1bd0f0c8 ]

NAND devices need additional data area (OOB) for error correction,
but it is also used for Bad Block Marker (BBM).  In many cases, the
first byte in OOB is used for BBM, but the location actually depends
on chip vendors.  The NAND controller should preserve the precious
BBM to keep track of bad blocks.

In Denali IP, the SPARE_AREA_SKIP_BYTES register is used to specify
the number of bytes to skip from the start of OOB.  The ECC engine
will automatically skip the specified number of bytes when it gets
access to OOB area.

The same value for SPARE_AREA_SKIP_BYTES should be used between
firmware and the operating system if you intend to use the NAND
device across the control hand-off.

In fact, the current denali.c code expects firmware to have already
set the SPARE_AREA_SKIP_BYTES register, then reads the value out.

If no firmware (or bootloader) has initialized the controller, the
register value is zero, which is the default after power-on-reset.
In other words, the Linux driver cannot initialize the controller
by itself.

Some possible solutions are:

 [1] Add a DT property to specify the skipped bytes in OOB
 [2] Associate the preferred value with compatible
 [3] Hard-code the default value in the driver

My first attempt was [1], but in the review process, [3] was suggested
as a counter-implementation.
(https://lore.kernel.org/patchwork/patch/983055/)

The default value 8 was chosen to match to the boot ROM of the UniPhier
platform.  The preferred value may vary by platform.  If so, please
trade up to a different solution.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit c7eabbee3de99347105faa7fd925a500ccf43baf ]

The device specific resource can be free in free_slot after
removing host controller.
Signed-off-by: NWang Dongsheng <dongsheng.wang@hxt-semitech.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 51698949 ]

This device reports SDHCI_CLOCK_INT_STABLE even though it's not
ready to take SDHCI_CLOCK_CARD_EN. The symptom is that reading
SDHCI_CLOCK_CONTROL after enabling the clock shows absence of the
bit from the register (e.g. expecting 0x0000fa07 = 0x0000fa03 |
SDHCI_CLOCK_CARD_EN but only observed the first operand).

mmc1: Timeout waiting for hardware cmd interrupt.
mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
mmc1: sdhci: Sys addr:  0x00000000 | Version:  0x00000603
mmc1: sdhci: Blk size:  0x00000000 | Blk cnt:  0x00000000
mmc1: sdhci: Argument:  0x00000000 | Trn mode: 0x00000000
mmc1: sdhci: Present:   0x01ff0001 | Host ctl: 0x00000001
mmc1: sdhci: Power:     0x0000000f | Blk gap:  0x00000000
mmc1: sdhci: Wake-up:   0x00000000 | Clock:    0x0000fa03
mmc1: sdhci: Timeout:   0x00000000 | Int stat: 0x00000000
mmc1: sdhci: Int enab:  0x00ff0083 | Sig enab: 0x00ff0083
mmc1: sdhci: AC12 err:  0x00000000 | Slot int: 0x00000000
mmc1: sdhci: Caps:      0x25fcc8bf | Caps_1:   0x00002077
mmc1: sdhci: Cmd:       0x00000000 | Max curr: 0x005800c8
mmc1: sdhci: Resp[0]:   0x00000000 | Resp[1]:  0x00000000
mmc1: sdhci: Resp[2]:   0x00000000 | Resp[3]:  0x00000000
mmc1: sdhci: Host ctl2: 0x00000008
mmc1: sdhci: ADMA Err:  0x00000000 | ADMA Ptr: 0x00000000
mmc1: sdhci: ============================================

The problem happens during wakeup from S3. Adding a delay quirk
after power up reliably fixes the problem.
Signed-off-by: NYu Zhao <yuzhao@google.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 7567c2a2ad9e80a2ce977eef535e64b61899633e ]

Forgot to include the maintainers with my first email.

Somewhere between Michael Lyle's original
"bcache: PI controller for writeback rate V2" patch dated 07 Sep 2017
and 1d316e65 bcache: implement PI controller for writeback rate,
the mapping of the writeback_rate_minimum attribute was dropped.

Re-add the missing sysfs writeback_rate_minimum attribute mapping to
"allow the user to specify a minimum rate at which dirty blocks are
retired."

Fixes: 1d316e65 ("bcache: implement PI controller for writeback rate")
Signed-off-by: NBen Peddell <klightspeed@killerwolves.net>
Signed-off-by: NColy Li <colyli@suse.de>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit f69ffc5d3db8f1f03fd6d1df5930f9a1fbd787b6 ]

cpupower crashes on VMWare guests.  The guests have the AMD PStateDef MSR
(0xC0010064 + state number) set to zero.  As a result fid and did are zero
and the crash occurs because of a divide by zero (cof = fid/did).  This
can be prevented by checking the enable bit in the PStateDef MSR before
calculating cof.  By doing this the value of pstate[i] remains zero and
the value can be tested before displaying the active Pstates.

Check the enable bit in the PstateDef register for all supported families
and only print out enabled Pstates.
Signed-off-by: NPrarit Bhargava <prarit@redhat.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Stafford Horne <shorne@gmail.com>
Signed-off-by: NShuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit ce49d8436cffa9b7a6a5f110879d53e89dbc6746 ]

Ensure that all code paths in strbuf_addv() call va_end() on the
ap_saved copy that was made.

Fixes the following coverity complaint:

  Error: VARARGS (CWE-237): [#def683]
  tools/perf/util/strbuf.c:106: missing_va_end: va_end was not called
  for "ap_saved".
Signed-off-by: NSanskriti Sharma <sansharm@redhat.com>
Reviewed-by: NJiri Olsa <jolsa@kernel.org>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Link: http://lkml.kernel.org/r/1538490554-8161-2-git-send-email-sansharm@redhat.comSigned-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 9c8a182e5a73e01afd11742a2ab887bf338fdafd ]

parse_ftrace_printk() tokenizes and parses a line, calling strdup() each
iteration.  Add code to free this temporary format string duplicate.

Fixes the following coverity complaints:

  Error: RESOURCE_LEAK (CWE-772):
  tools/perf/util/trace-event-parse.c:158: overwrite_var: Overwriting
  "printk" in "printk = strdup(fmt + 1)" leaks the storage that "printk"
  points to.

  tools/perf/util/trace-event-parse.c:162: leaked_storage: Variable
  "printk" going out of scope leaks the storage it points to.
Signed-off-by: NSanskriti Sharma <sansharm@redhat.com>
Reviewed-by: NJiri Olsa <jolsa@kernel.org>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Link: http://lkml.kernel.org/r/1538490554-8161-4-git-send-email-sansharm@redhat.comSigned-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit faedbf3fd19f2511a39397f76359e4cc6ee93072 ]

Free tracing_data structure in tracing_data_get() error paths.

Fixes the following coverity complaint:

  Error: RESOURCE_LEAK (CWE-772):
  leaked_storage: Variable "tdata" going out of scope leaks the storage
Signed-off-by: NSanskriti Sharma <sansharm@redhat.com>
Reviewed-by: NJiri Olsa <jolsa@kernel.org>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Link: http://lkml.kernel.org/r/1538490554-8161-3-git-send-email-sansharm@redhat.comSigned-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 1e44224fb0528b4c0cc176bde2bb31e9127eb14b ]

For each system in a given pevent, read_event_files() reads in a
temporary 'sys' string.  Be sure to free this string before moving onto
to the next system and/or leaving read_event_files().

Fixes the following coverity complaints:

  Error: RESOURCE_LEAK (CWE-772):

  tools/perf/util/trace-event-read.c:343: overwrite_var: Overwriting
  "sys" in "sys = read_string()" leaks the storage that "sys" points to.

  tools/perf/util/trace-event-read.c:353: leaked_storage: Variable "sys"
  going out of scope leaks the storage it points to.
Signed-off-by: NSanskriti Sharma <sansharm@redhat.com>
Reviewed-by: NJiri Olsa <jolsa@kernel.org>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Link: http://lkml.kernel.org/r/1538490554-8161-6-git-send-email-sansharm@redhat.comSigned-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit a1108c7b2efb892350ba6a0e932dfd45622f4e2b ]

Clang warns when one enumerated type is implicitly converted to another.

drivers/spi/spi-ep93xx.c:342:62: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
        nents = dma_map_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
                ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:428:58: note: expanded from macro
'dma_map_sg'
#define dma_map_sg(d, s, n, r) dma_map_sg_attrs(d, s, n, r, 0)
                               ~~~~~~~~~~~~~~~~          ^
drivers/spi/spi-ep93xx.c:348:57: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
                dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
                ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:429:62: note: expanded from macro
'dma_unmap_sg'
#define dma_unmap_sg(d, s, n, r) dma_unmap_sg_attrs(d, s, n, r, 0)
                                 ~~~~~~~~~~~~~~~~~~          ^
drivers/spi/spi-ep93xx.c:377:56: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
        dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
        ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:429:62: note: expanded from macro
'dma_unmap_sg'
#define dma_unmap_sg(d, s, n, r) dma_unmap_sg_attrs(d, s, n, r, 0)
                                 ~~~~~~~~~~~~~~~~~~          ^
3 warnings generated.

dma_{,un}map_sg expect an enum of type dma_data_direction but this
driver uses dma_transfer_direction for everything. Convert the driver to
use dma_data_direction for these two functions.

There are two places that strictly require an enum of type
dma_transfer_direction: the direction member in struct dma_slave_config
and the direction parameter in dmaengine_prep_slave_sg. To avoid using
an explicit cast, add a simple function, ep93xx_dma_data_to_trans_dir,
to safely map between the two types because they are not 1 to 1 in
meaning.
Signed-off-by: NNathan Chancellor <natechancellor@gmail.com>
Reviewed-by: NNick Desaulniers <ndesaulniers@google.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit d8adaa3b86324c6186d0adf74bc256bdacfffdb6 ]

In pblk, when a new line is allocated, metadata for the previously
written line is scheduled. This is done through a fixed memory region
that is shared through time and contexts across different lines and
therefore protected by a lock. Unfortunately, this lock is not properly
covering all the metadata used for sharing this memory regions,
resulting in a race condition.

This patch fixes this race condition by protecting this metadata
properly.

Fixes: dd2a4343 ("lightnvm: pblk: sched. metadata on write thread")
Signed-off-by: NJavier González <javier@cnexlabs.com>
Signed-off-by: NMatias Bjørling <mb@lightnvm.io>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 7325b4bbe5952e3e939f15de812f2ee0c0d33ca9 ]

The driver may sleep with holding a spinlock.

The function call paths (from bottom to top) in Linux-4.16 are:

[FUNC] nvm_dev_dma_alloc(GFP_KERNEL)
drivers/lightnvm/pblk-core.c, 754:
	nvm_dev_dma_alloc in pblk_line_submit_smeta_io
drivers/lightnvm/pblk-core.c, 1048:
	pblk_line_submit_smeta_io in pblk_line_init_bb
drivers/lightnvm/pblk-core.c, 1434:
	pblk_line_init_bb in pblk_line_replace_data
drivers/lightnvm/pblk-recovery.c, 980:
	pblk_line_replace_data in pblk_recov_l2p
drivers/lightnvm/pblk-recovery.c, 976:
	spin_lock in pblk_recov_l2p

[FUNC] bio_map_kern(GFP_KERNEL)
drivers/lightnvm/pblk-core.c, 762:
	bio_map_kern in pblk_line_submit_smeta_io
drivers/lightnvm/pblk-core.c, 1048:
	pblk_line_submit_smeta_io in pblk_line_init_bb
drivers/lightnvm/pblk-core.c, 1434:
	pblk_line_init_bb in pblk_line_replace_data
drivers/lightnvm/pblk-recovery.c, 980:
	pblk_line_replace_data in pblk_recov_l2p
drivers/lightnvm/pblk-recovery.c, 976:
	spin_lock in pblk_recov_l2p

To fix these bugs, the call to pblk_line_replace_data()
is moved out of the spinlock protection.

These bugs are found by my static analysis tool DSAC.
Signed-off-by: NJia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: NJavier González <javier@cnexlabs.com>
Signed-off-by: NMatias Bjørling <mb@lightnvm.io>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 44cdbdc657b23f75736eca3e88b781f009104363 ]

pblk exposes a sysfs interface that represents its internal state. Part
of this state is the map bitmap for the current open line, which should
be protected by the line lock to avoid a race when freeing the line
metadata. Currently, it is not.

This patch makes sure that the line state is consistent and NULL
bitmap pointers are not dereferenced.
Signed-off-by: NJavier González <javier@cnexlabs.com>
Signed-off-by: NMatias Bjørling <mb@lightnvm.io>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 95dcd64bc5a27080beaa344edfe5bdcca3d2e7dc ]

Technically this is not required because disabling the PWM should be
enough. However, when support for atomic operations was implemented in
the PWM subsystem, only actual changes to the PWM channel are applied
during pwm_config(), which means that during after resume from suspend
the old settings won't be applied.

One possible solution is for the PWM driver to implement its own PM
operations such that settings from before suspend get applied on resume.
This has the disadvantage of completely ignoring any particular ordering
requirements that PWM user drivers might have, so it is best to leave it
up to the user drivers to apply the settings that they want at the
appropriate time.

Another way to solve this would be to read back the current state of the
PWM at the time of resume. That way, in case the configuration was lost
during suspend, applying the old settings in PWM user drivers would
actually get them applied because they differ from the current settings.
However, not all PWM drivers support reading the hardware state, and not
all hardware may support it.

The best workaround at this point seems to be to let PWM user drivers
tell the PWM subsystem that the PWM is turned off by, in addition to
disabling it, also setting the duty cycle to 0. This causes the resume
operation to apply a configuration that is different from the current
configuration, resulting in the proper state from before suspend getting
restored.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit b5130dc2 ]

When running as a level 3 guest with no host provided sthyi support
sclp_ocf_cpc_name_copy() will only return zeroes. Zeroes are not a
valid group name, so let's not indicate that the group name field is
valid.

Also the group name is not dependent on stsi, let's not return based
on stsi before setting it.

Fixes: 95ca2cb5 ("KVM: s390: Add sthyi emulation")
Signed-off-by: NJanosch Frank <frankja@linux.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit df52eab2 ]

Configuring generic network device parameters on tun will fail in
presence of IFLA_INFO_KIND attribute in IFLA_LINKINFO nested attribute
since tun_validate() always return failure.

This can be visualized with following ip-link(8) command sequences:

  # ip link set dev tun0 group 100
  # ip link set dev tun0 group 100 type tun
  RTNETLINK answers: Invalid argument

with contrast to dummy and veth drivers:

  # ip link set dev dummy0 group 100
  # ip link set dev dummy0 type dummy

  # ip link set dev veth0 group 100
  # ip link set dev veth0 group 100 type veth

Fix by returning zero in tun_validate() when @data is NULL that is
always in case since rtnl_link_ops->maxtype is zero in tun driver.

Fixes: f019a7a5 ("tun: Implement ip link del tunXXX")
Signed-off-by: NSerhey Popovych <serhe.popovych@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 5948185b97fa1f83d7855e638a72982a1073ebf5 ]

This commit makes it possible to use devlink to split the 100G CXP
Netronome into two 40G interfaces. Currently when you ask for 2
interfaces, the math in src/nfp_devlink.c:nfp_devlink_port_split
calculates that you want 5 lanes per port because for some reason
eth_port.port_lanes=10 (shouldn't this be 12 for CXP?). What we really
want when asking for 2 breakout interfaces is 4 lanes per port. This
commit makes that happen by calculating based on 8 lanes if 10 are
present.
Signed-off-by: NRyan C Goodfellow <rgoodfel@isi.edu>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NGreg Weeks <greg.weeks@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 00547955 ]

The VF device's serial number is saved as a string in PCI slot's
kobj name, not the slot->number. This patch corrects the netvsc
driver, so the VF device can be successfully paired with synthetic
NIC.

Fixes: 00d7ddba ("hv_netvsc: pair VF based on serial number")
Reported-by: NVitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 8ab66cbe63aeaf9e5970fb4aaef1c660fca59321 ]

The matches() routine for a capability must honor the "scope"
passed to it and return the proper results.
i.e, when passed with SCOPE_LOCAL_CPU, it should check the
status of the capability on the current CPU. This is used by
verify_local_cpu_capabilities() on a late secondary CPU to make
sure that it's compliant with the established system features.
However, ARM64_HAS_CACHE_{IDC/DIC} always checks the system wide
registers and this could mean that a late secondary CPU could return
"true" (since the CPU hasn't updated the system wide registers yet)
and thus lead the system in an inconsistent state, where
the system assumes it has IDC/DIC feature, while the new CPU
doesn't.

Fixes: commit 6ae4b6e0 ("arm64: Add support for new control bits CTR_EL0.DIC and CTR_EL0.IDC")
Cc: Philip Elcan <pelcan@codeaurora.org>
Cc: Shanker Donthineni <shankerd@codeaurora.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: NSuzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 1448a2a5360ae06f25e2edc61ae070dff5c0beb4 ]

If we fail to allocate the request queue for a disk, we still need to
free that disk, not just the previous ones. Additionally, we need to
cleanup the previous request queues.
Signed-off-by: NOmar Sandoval <osandov@fb.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 71327f547ee3a46ec5c39fdbbd268401b2578d0e ]

Move queue allocation next to disk allocation to fix a couple of issues:

- If add_disk() hasn't been called, we should clear disk->queue before
  calling put_disk().
- If we fail to allocate a request queue, we still need to put all of
  the disks, not just the ones that we allocated queues for.
Signed-off-by: NOmar Sandoval <osandov@fb.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit cb20f2d2c0507d60d94ef896991e95708f051dd1 ]

The commit 2eb0f624 ("netfilter: add NAT support for shifted
portmap ranges") did not set the checkentry/destroy callbacks for
the newly added DNAT target. As a result, rulesets using only
such nat targets are not effective, as the relevant conntrack hooks
are not enabled.
The above affect also nft_compat rulesets.
Fix the issue adding the missing initializers.

Fixes: 2eb0f624 ("netfilter: add NAT support for shifted portmap ranges")
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 9506a7425b094d2f1d9c877ed5a78f416669269b ]

It was found that when debug_locks was turned off because of a problem
found by the lockdep code, the system performance could drop quite
significantly when the lock_stat code was also configured into the
kernel. For instance, parallel kernel build time on a 4-socket x86-64
server nearly doubled.

Further analysis into the cause of the slowdown traced back to the
frequent call to debug_locks_off() from the __lock_acquired() function
probably due to some inconsistent lockdep states with debug_locks
off. The debug_locks_off() function did an unconditional atomic xchg
to write a 0 value into debug_locks which had already been set to 0.
This led to severe cacheline contention in the cacheline that held
debug_locks.  As debug_locks is being referenced in quite a few different
places in the kernel, this greatly slow down the system performance.

To prevent that trashing of debug_locks cacheline, lock_acquired()
and lock_contended() now checks the state of debug_locks before
proceeding. The debug_locks_off() function is also modified to check
debug_locks before calling __debug_locks_off().
Signed-off-by: NWaiman Long <longman@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Link: http://lkml.kernel.org/r/1539913518-15598-1-git-send-email-longman@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 4c16128b6271e70c8743178e90cccee147858503 ]

At least UDP / TCP stacks can now cook skbs with a tstamp using
MONOTONIC base (or arbitrary values with SCM_TXTIME)

Since loopback driver does not call (directly or indirectly)
skb_scrub_packet(), we need to clear skb->tstamp so that
net_timestamp_check() can eventually resample the time,
using ktime_get_real().

Fixes: 80b14dee ("net: Add a new socket option for a future transmit time.")
Fixes: fb420d5d91c1 ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: NSoheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 8d5b0bf611ec5b7618d5b772dddc93b8afa78cb8 ]

We observed that packets and bytes count are not reset
when user performs interface down. Eventually, tx queue is
exhausted and packets will not be sent out.
To avoid this problem, resets tx queue in ndo_stop.

Fixes: 533dd11a ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: NMasahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: NYoshitoyo Osaki <osaki.yoshitoyo@socionext.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f5e758b8358f6c27e8a351ddf0b441a64cdabb94 upstream.

PMIC_IRQB and PMIC_KEYINB lines on Exynos4210-based Origen board have
external pull-up resistors, so disable any pull control for those lines
in respective pin controller node. This fixes support for MAX8997
interrupts and enables operation of wakeup from MAX8997 RTC alarm.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Fixes: 17419726 ("ARM: dts: add max8997 device node for exynos4210-origen board")
Cc: <stable@vger.kernel.org>
Signed-off-by: NKrzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c6ee7a548e2c291398b4f32c1f741c66b9f98e1c upstream.

The numa_emulation() routine in the 'uniform' case walks through all the
physical 'memblk' instances and divides them into N emulated nodes with
split_nodes_size_interleave_uniform(). As each physical node is consumed it
is removed from the physical memblk array in the numa_remove_memblk_from()
helper.

Since split_nodes_size_interleave_uniform() handles advancing the array as
the 'memblk' is consumed it is expected that the base of the array is
always specified as the argument.

Otherwise, on multi-socket (> 2) configurations the uniform-split
capability can generate an invalid numa configuration leading to boot
failures with signatures like the following:

    rcu: INFO: rcu_sched detected stalls on CPUs/tasks:
    Sending NMI from CPU 0 to CPUs 2:
    NMI backtrace for cpu 2
    CPU: 2 PID: 1332 Comm: pgdatinit0 Not tainted 4.19.0-rc8-next-20181019-baseline #59
    RIP: 0010:__init_single_page.isra.74+0x81/0x90
    [..]
    Call Trace:
     deferred_init_pages+0xaa/0xe3
     deferred_init_memmap+0x18f/0x318
     kthread+0xf8/0x130
     ? deferred_free_pages.isra.105+0xc9/0xc9
     ? kthread_stop+0x110/0x110
     ret_from_fork+0x35/0x40

Fixes: 1f6a2c6d9f121 ("x86/numa_emulation: Introduce uniform split capability")
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NAlexander Duyck <alexander.h.duyck@linux.intel.com>
Reviewed-by: NDave Hansen <dave.hansen@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/154049911459.2685845.9210186007479774286.stgit@dwillia2-desk3.amr.corp.intel.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f77084d96355f5fba8e2c1fb3a51a393b1570de7 upstream.

The WARN_ON_ONCE(__read_cr3() != build_cr3()) in switch_mm_irqs_off()
triggers every once in a while during a snapshotted system upgrade.

The warning triggers since commit decab088 ("x86/mm: Remove
preempt_disable/enable() from __native_flush_tlb()"). The callchain is:

  get_page_from_freelist() -> post_alloc_hook() -> __kernel_map_pages()

with CONFIG_DEBUG_PAGEALLOC enabled.

Disable preemption during CR3 reset / __flush_tlb_all() and add a comment
why preemption has to be disabled so it won't be removed accidentaly.

Add another preemptible() check in __flush_tlb_all() to catch callers with
enabled preemption when PGE is enabled, because PGE enabled does not
trigger the warning in __native_flush_tlb(). Suggested by Andy Lutomirski.

Fixes: decab088 ("x86/mm: Remove preempt_disable/enable() from __native_flush_tlb()")
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181017103432.zgv46nlu3hc7k4rq@linutronix.deSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a1b0c1c64dfef0cff8555bb708bfc5d7c66c6ca4 upstream.

It is perfectly valid for a guest to do VMXON and not do VMPTRLD. This
state needs to be preserved on migration.

Cc: stable@vger.kernel.org
Fixes: 8fcc4b59Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/corruption-check: Fix panic in memory_corruption_check() when boot option without value is provided

commit ccde460b9ae5c2bd5e4742af0a7f623c2daad566 upstream.

memory_corruption_check[{_period|_size}]()'s handlers do not check input
argument before passing it to kstrtoul() or simple_strtoull(). The argument
would be a NULL pointer if each of the kernel parameters, without its
value, is set in command line and thus cause the following panic.

PANIC: early exception 0xe3 IP 10:ffffffff73587c22 error 0 cr2 0x0
[    0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 4.18-rc8+ #2
[    0.000000] RIP: 0010:kstrtoull+0x2/0x10
...
[    0.000000] Call Trace
[    0.000000]  ? set_corruption_check+0x21/0x49
[    0.000000]  ? do_early_param+0x4d/0x82
[    0.000000]  ? parse_args+0x212/0x330
[    0.000000]  ? rdinit_setup+0x26/0x26
[    0.000000]  ? parse_early_options+0x20/0x23
[    0.000000]  ? rdinit_setup+0x26/0x26
[    0.000000]  ? parse_early_param+0x2d/0x39
[    0.000000]  ? setup_arch+0x2f7/0xbf4
[    0.000000]  ? start_kernel+0x5e/0x4c2
[    0.000000]  ? load_ucode_bsp+0x113/0x12f
[    0.000000]  ? secondary_startup_64+0xa5/0xb0

This patch adds checks to prevent the panic.
Signed-off-by: NHe Zhe <zhe.he@windriver.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: gregkh@linuxfoundation.org
Cc: kstewart@linuxfoundation.org
Cc: pombredanne@nexb.com
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1534260823-87917-1-git-send-email-zhe.he@windriver.comSigned-off-by: NIngo Molnar <mingo@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 357d291ce035d1b757568058f3c9898c60d125b1 upstream.

The boot loader version reported via sysfs is wrong in case of the
kernel being booted via the Xen PVH boot entry. it should be 2.12
(0x020c), but it is reported to be 2.18 (0x0212).

As the current way to set the version is error prone use the more
readable variant (2 << 8) | 12.
Signed-off-by: NJuergen Gross <jgross@suse.com>
Cc: <stable@vger.kernel.org> # 4.12
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: boris.ostrovsky@oracle.com
Cc: bp@alien8.de
Cc: corbet@lwn.net
Cc: linux-doc@vger.kernel.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/20181010061456.22238-2-jgross@suse.comSigned-off-by: NIngo Molnar <mingo@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 53c613fe6349994f023245519265999eed75957f upstream.

STIBP is a feature provided by certain Intel ucodes / CPUs. This feature
(once enabled) prevents cross-hyperthread control of decisions made by
indirect branch predictors.

Enable this feature if

- the CPU is vulnerable to spectre v2
- the CPU supports SMT and has SMT siblings online
- spectre_v2 mitigation autoselection is enabled (default)

After some previous discussion, this leaves STIBP on all the time, as wrmsr
on crossing kernel boundary is a no-no. This could perhaps later be a bit
more optimized (like disabling it in NOHZ, experiment with disabling it in
idle, etc) if needed.

Note that the synchronization of the mask manipulation via newly added
spec_ctrl_mutex is currently not strictly needed, as the only updater is
already being serialized by cpu_add_remove_lock, but let's make this a
little bit more future-proof.
Signed-off-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc:  "WoodhouseDavid" <dwmw@amazon.co.uk>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc:  "SchauflerCasey" <casey.schaufler@intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/nycvar.YFH.7.76.1809251438240.15880@cbobk.fhfr.pmSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5e93a125f521efd00d71af31c2a301f3d46af48c upstream.

Since the commit c647f806 ("ALSA: hda - Allow multiple ADCs for
mic mute LED controls") we allow enabling the mic mute LED with
multiple ADCs.  The commit changed the function return value to be
zero or a negative error, while this change was overlooked in the
thinkpad_acpi helper code where it still expects a positive return
value for success.  This eventually leads to a NULL dereference on a
system that has only a mic mute LED.

This patch corrects the return value check in the corresponding code
as well.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201621
Fixes: c647f806 ("ALSA: hda - Allow multiple ADCs for mic mute LED controls")
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ac237c28d5ac1b241d58b1b7b4b9fa10efb22fb5 upstream.

The Creative Audigy SE (SB0570) card currently exhibits an audible pop
whenever playback is stopped or resumed, or during silent periods of an
audio stream. Initialise the IZD bit to the 0 to eliminate these pops.

The Infinite Zero Detection (IZD) feature on the DAC causes the output
to be shunted to Vcap after 2048 samples of silence. This discharges the
AC coupling capacitor through the output and causes the aforementioned
pop/click noise.

The behaviour of the IZD bit is described on page 15 of the WM8768GEDS
datasheet: "With IZD=1, applying MUTE for 1024 consecutive input samples
will cause all outputs to be connected directly to VCAP. This also
happens if 2048 consecutive zero input samples are applied to all 6
channels, and IZD=0. It will be removed as soon as any channel receives
a non-zero input". I believe the second sentence might be referring to
IZD=1 instead of IZD=0 given the observed behaviour of the card.

This change should make the DAC initialisation consistent with
Creative's Windows driver, as this popping persists when initialising
the card in Linux and soft rebooting into Windows, but is not present on
a cold boot to Windows.
Signed-off-by: NAlex Stanoev <alex@astanoev.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5cb6b5fc013ee711d19bfc4e9deb8d6ae80741db upstream.

Power-saving is causing plops on audio start/stop on Dell Precision T3600
laptops and Intel DZ77BH boards, add these to the power_save blacklist.

BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1525104Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>