- 26 5月, 2019 1 次提交
-
-
由 Vitaly Kuznetsov 提交于
[ Upstream commit da66761c2d93a46270d69001abb5692717495a68 ] It was reported that with some special Multi Processor Group configuration, e.g: bcdedit.exe /set groupsize 1 bcdedit.exe /set maxgroup on bcdedit.exe /set groupaware on for a 16-vCPU guest WS2012 shows BSOD on boot when PV TLB flush mechanism is in use. Tracing kvm_hv_flush_tlb immediately reveals the issue: kvm_hv_flush_tlb: processor_mask 0x0 address_space 0x0 flags 0x2 The only flag set in this request is HV_FLUSH_ALL_VIRTUAL_ADDRESS_SPACES, however, processor_mask is 0x0 and no HV_FLUSH_ALL_PROCESSORS is specified. We don't flush anything and apparently it's not what Windows expects. TLFS doesn't say anything about such requests and newer Windows versions seem to be unaffected. This all feels like a WS2012 bug, which is, however, easy to workaround in KVM: let's flush everything when we see an empty flush request, over-flushing doesn't hurt. Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
- 06 8月, 2018 1 次提交
-
-
由 Paolo Bonzini 提交于
Some of the MSRs returned by GET_MSR_INDEX_LIST currently cannot be sent back to KVM_GET_MSR and/or KVM_SET_MSR; either they can never be sent back, or you they are only accepted under special conditions. This makes the API a pain to use. To avoid this pain, this patch makes it so that the result of the get-list ioctl can always be used for host-initiated get and set. Since we don't have a separate way to check for read-only MSRs, this means some Hyper-V MSRs are ignored when written. Arguably they should not even be in the result of GET_MSR_INDEX_LIST, but I am leaving there in case userspace is using the outcome of GET_MSR_INDEX_LIST to derive the support for the corresponding Hyper-V feature. Cc: stable@vger.kernel.org Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
- 26 5月, 2018 5 次提交
-
-
由 Vitaly Kuznetsov 提交于
Implement HvFlushVirtualAddress{List,Space}Ex hypercalls in the same way we've implemented non-EX counterparts. Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com> [Initialized valid_bank_mask to silence misguided GCC warnigs. - Radim] Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
-
由 Vitaly Kuznetsov 提交于
Implement HvFlushVirtualAddress{List,Space} hypercalls in a simplistic way: do full TLB flush with KVM_REQ_TLB_FLUSH and kick vCPUs which are currently IN_GUEST_MODE. Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
-
由 Vitaly Kuznetsov 提交于
Prepare to support TLB flush hypercalls, some of which are REP hypercalls. Also, return HV_STATUS_INVALID_HYPERCALL_INPUT as it seems more appropriate. Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
-
由 Vitaly Kuznetsov 提交于
Avoid open-coding offsets for hypercall input parameters, we already have defines for them. Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
-
由 Radim Krčmář 提交于
If the hypercall was called from userspace or real mode, KVM injects #UD and then advances RIP, so it looks like #UD was caused by the following instruction. This probably won't cause more than confusion, but could give an unexpected access to guest OS' instruction emulator. Also, refactor the code to count hv hypercalls that were handled by the virt userspace. Fixes: 6356ee0c ("x86: Delay skip of emulated hypercall instruction") Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com> Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
-
- 11 5月, 2018 2 次提交
-
-
由 Paolo Bonzini 提交于
Even though the eventfd is released after the KVM SRCU grace period elapses, the conn_to_evt data structure itself is not; it uses RCU internally, instead. Fix the read-side critical section to happen under rcu_read_lock/unlock; the result is still protected by vcpu->kvm->srcu. Reviewed-by: NRoman Kagan <rkagan@virtuozzo.com> Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
由 Marian Rotariu 提交于
The IP increment should be done after the hypercall emulation, after calling the various handlers. In this way, these handlers can accurately identify the the IP of the VMCALL if they need it. This patch keeps the same functionality for the Hyper-V handler which does not use the return code of the standard kvm_skip_emulated_instruction() call. Signed-off-by: NMarian Rotariu <mrotariu@bitdefender.com> [Hyper-V hypercalls also need kvm_skip_emulated_instruction() - Paolo] Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
- 29 3月, 2018 1 次提交
-
-
由 Ladi Prosek 提交于
The assist page has been used only for the paravirtual EOI so far, hence the "APIC" in the MSR name. Renaming to match the Hyper-V TLFS where it's called "Virtual VP Assist MSR". Signed-off-by: NLadi Prosek <lprosek@redhat.com> Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com> Acked-by: NThomas Gleixner <tglx@linutronix.de> Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
-
- 24 3月, 2018 1 次提交
-
-
由 Dan Carpenter 提交于
"rep_done" is always zero so the "(((u64)rep_done & 0xfff) << 32)" expression is just zero. We can remove the "res" temporary variable as well and just use "ret" directly. Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com> Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
- 17 3月, 2018 3 次提交
-
-
由 Vitaly Kuznetsov 提交于
Hyper-V 2016 on KVM with SynIC enabled doesn't boot with the following trace: kvm_entry: vcpu 0 kvm_exit: reason MSR_WRITE rip 0xfffff8000131c1e5 info 0 0 kvm_hv_synic_set_msr: vcpu_id 0 msr 0x40000090 data 0x10000 host 0 kvm_msr: msr_write 40000090 = 0x10000 (#GP) kvm_inj_exception: #GP (0x0) KVM acts according to the following statement from TLFS: " 11.8.4 SINTx Registers ... Valid values for vector are 16-255 inclusive. Specifying an invalid vector number results in #GP. " However, I checked and genuine Hyper-V doesn't #GP when we write 0x10000 to SINTx. I checked with Microsoft and they confirmed that if either the Masked bit (bit 16) or the Polling bit (bit 18) is set to 1, then they ignore the value of Vector. Make KVM act accordingly. Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com> Reviewed-by: NRoman Kagan <rkagan@virtuozzo.com> Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
-
由 Vitaly Kuznetsov 提交于
When a new vector is written to SINx we update vec_bitmap/auto_eoi_bitmap but we forget to remove old vector from these masks (in case it is not present in some other SINTx). Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com> Reviewed-by: NRoman Kagan <rkagan@virtuozzo.com> Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
-
由 Vitaly Kuznetsov 提交于
Nested Hyper-V/Windows guest running on top of KVM will use TSC page clocksource in two cases: - L0 exposes invariant TSC (CPUID.80000007H:EDX[8]). - L0 provides Hyper-V Reenlightenment support (CPUID.40000003H:EAX[13]). Exposing invariant TSC effectively blocks migration to hosts with different TSC frequencies, providing reenlightenment support will be needed when we start migrating nested workloads. Implement rudimentary support for reenlightenment MSRs. For now, these are just read/write MSRs with no effect. Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com> Reviewed-by: NRoman Kagan <rkagan@virtuozzo.com> Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
-
- 07 3月, 2018 2 次提交
-
-
由 Roman Kagan 提交于
In Hyper-V, the fast guest->host notification mechanism is the SIGNAL_EVENT hypercall, with a single parameter of the connection ID to signal. Currently this hypercall incurs a user exit and requires the userspace to decode the parameters and trigger the notification of the potentially different I/O context. To avoid the costly user exit, process this hypercall and signal the corresponding eventfd in KVM, similar to ioeventfd. The association between the connection id and the eventfd is established via the newly introduced KVM_HYPERV_EVENTFD ioctl, and maintained in an (srcu-protected) IDR. Signed-off-by: NRoman Kagan <rkagan@virtuozzo.com> Reviewed-by: NDavid Hildenbrand <david@redhat.com> [asm/hyperv.h changes approved by KY Srinivasan. - Radim] Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
-
由 Roman Kagan 提交于
Move kvm.arch.hyperv initialization and cleanup to separate functions. For now only a mutex is inited in the former, and the latter is empty; more stuff will go in there in a followup patch. Signed-off-by: NRoman Kagan <rkagan@virtuozzo.com> Reviewed-by: NDavid Hildenbrand <david@redhat.com> Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
-
- 08 8月, 2017 2 次提交
-
-
由 Longpeng(Mike) 提交于
get_cpl requires vcpu_load, so we must cache the result (whether the vcpu was preempted when its cpl=0) in kvm_vcpu_arch. Signed-off-by: NLongpeng(Mike) <longpeng2@huawei.com> Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
由 Longpeng(Mike) 提交于
If a vcpu exits due to request a user mode spinlock, then the spinlock-holder may be preempted in user mode or kernel mode. (Note that not all architectures trap spin loops in user mode, only AMD x86 and ARM/ARM64 currently do). But if a vcpu exits in kernel mode, then the holder must be preempted in kernel mode, so we should choose a vcpu in kernel mode as a more likely candidate for the lock holder. This introduces kvm_arch_vcpu_in_kernel() to decide whether the vcpu is in kernel-mode when it's preempted. kvm_vcpu_on_spin's new argument says the same of the spinning VCPU. Signed-off-by: NLongpeng(Mike) <longpeng2@huawei.com> Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
- 07 8月, 2017 1 次提交
-
-
由 Ladi Prosek 提交于
It has been experimentally confirmed that supporting these two MSRs is one of the necessary conditions for nested Hyper-V to use the TSC page. Modern Windows guests are noticeably slower when they fall back to reading timestamps from the HV_X64_MSR_TIME_REF_COUNT MSR instead of using the TSC page. The newly supported MSRs are advertised with the AccessFrequencyRegs partition privilege flag and CPUID.40000003H:EDX[8] "Support for determining timer frequencies is available" (both outside of the scope of this KVM patch). Reviewed-by: NRadim Krčmář <rkrcmar@redhat.com> Signed-off-by: NLadi Prosek <lprosek@redhat.com> Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
- 20 7月, 2017 1 次提交
-
-
由 Roman Kagan 提交于
If the SynIC timer message delivery fails due to SINT message slot being busy, there's no point to attempt starting the timer again until we're notified of the slot being released by the guest (via EOM or EOI). Even worse, when a oneshot timer fails to deliver its message, its re-arming with an expiration time in the past leads to immediate retry of the delivery, and so on, without ever letting the guest vcpu to run and release the slot, which results in a livelock. To avoid that, only start the timer when there's no timer message pending delivery. When there is, meaning the slot is busy, the processing will be restarted upon notification from the guest that the slot is released. Signed-off-by: NRoman Kagan <rkagan@virtuozzo.com> Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
-
- 14 7月, 2017 1 次提交
-
-
由 Roman Kagan 提交于
Hyper-V identifies vCPUs by Virtual Processor Index, which can be queried via HV_X64_MSR_VP_INDEX msr. It is defined by the spec as a sequential number which can't exceed the maximum number of vCPUs per VM. APIC ids can be sparse and thus aren't a valid replacement for VP indices. Current KVM uses its internal vcpu index as VP_INDEX. However, to make it predictable and persistent across VM migrations, the userspace has to control the value of VP_INDEX. This patch achieves that, by storing vp_index explicitly on vcpu, and allowing HV_X64_MSR_VP_INDEX to be set from the host side. For compatibility it's initialized to KVM vcpu index. Also a few variables are renamed to make clear distinction betweed this Hyper-V vp_index and KVM vcpu_id (== APIC id). Besides, a new capability, KVM_CAP_HYPERV_VP_INDEX, is added to allow the userspace to skip attempting msr writes where unsupported, to avoid spamming error logs. Signed-off-by: NRoman Kagan <rkagan@virtuozzo.com> Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
-
- 13 7月, 2017 1 次提交
-
-
由 Roman Kagan 提交于
There is a flaw in the Hyper-V SynIC implementation in KVM: when message page or event flags page is enabled by setting the corresponding msr, KVM zeroes it out. This is problematic because on migration the corresponding MSRs are loaded on the destination, so the content of those pages is lost. This went unnoticed so far because the only user of those pages was in-KVM hyperv synic timers, which could continue working despite that zeroing. Newer QEMU uses those pages for Hyper-V VMBus implementation, and zeroing them breaks the migration. Besides, in newer QEMU the content of those pages is fully managed by QEMU, so zeroing them is undesirable even when writing the MSRs from the guest side. To support this new scheme, introduce a new capability, KVM_CAP_HYPERV_SYNIC2, which, when enabled, makes sure that the synic pages aren't zeroed out in KVM. Signed-off-by: NRoman Kagan <rkagan@virtuozzo.com> Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
-
- 02 3月, 2017 1 次提交
-
-
由 Ingo Molnar 提交于
sched/headers: Prepare to move cputime functionality from <linux/sched.h> into <linux/sched/cputime.h> Introduce a trivial, mostly empty <linux/sched/cputime.h> header to prepare for the moving of cputime functionality out of sched.h. Update all code that relies on these facilities. Acked-by: NLinus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by: NIngo Molnar <mingo@kernel.org>
-
- 01 2月, 2017 1 次提交
-
-
由 Frederic Weisbecker 提交于
Now that most cputime readers use the transition API which return the task cputime in old style cputime_t, we can safely store the cputime in nsecs. This will eventually make cputime statistics less opaque and more granular. Back and forth convertions between cputime_t and nsecs in order to deal with cputime_t random granularity won't be needed anymore. Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@redhat.com> Cc: Stanislaw Gruszka <sgruszka@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Cc: Wanpeng Li <wanpeng.li@hotmail.com> Link: http://lkml.kernel.org/r/1485832191-26889-8-git-send-email-fweisbec@gmail.comSigned-off-by: NIngo Molnar <mingo@kernel.org>
-
- 09 1月, 2017 1 次提交
-
-
由 Radim Krčmář 提交于
Interrupt to self can be sent without knowing the APIC ID. Reviewed-by: NDavid Hildenbrand <david@redhat.com> Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com> Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
- 17 12月, 2016 1 次提交
-
-
由 Paolo Bonzini 提交于
Introduce a new mutex to avoid an AB-BA deadlock between kvm->lock and vcpu->mutex. Protect accesses in kvm_hv_setup_tsc_page too, as suggested by Roman. Reported-by: NDmitry Vyukov <dvyukov@google.com> Reviewed-by: NRoman Kagan <rkagan@virtuozzo.com> Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
- 17 11月, 2016 1 次提交
-
-
由 Jiang Biao 提交于
synic_set_irq is only used in hyperv.c, and should be static to avoid compiling warning when with -Wmissing-prototypes option. Signed-off-by: NJiang Biao <jiang.biao2@zte.com.cn> Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
- 20 9月, 2016 2 次提交
-
-
由 Paolo Bonzini 提交于
Lately tsc page was implemented but filled with empty values. This patch setup tsc page scale and offset based on vcpu tsc, tsc_khz and HV_X64_MSR_TIME_REF_COUNT value. The valid tsc page drops HV_X64_MSR_TIME_REF_COUNT msr reads count to zero which potentially improves performance. Signed-off-by: NAndrey Smetanin <asmetanin@virtuozzo.com> Reviewed-by: NPeter Hornyack <peterhornyack@google.com> Reviewed-by: NRadim Krčmář <rkrcmar@redhat.com> CC: Paolo Bonzini <pbonzini@redhat.com> CC: Roman Kagan <rkagan@virtuozzo.com> CC: Denis V. Lunev <den@openvz.org> [Computation of TSC page parameters rewritten to use the Linux timekeeper parameters. - Paolo] Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
由 Paolo Bonzini 提交于
Introduce a function that reads the exact nanoseconds value that is provided to the guest in kvmclock. This crystallizes the notion of kvmclock as a thin veneer over a stable TSC, that the guest will (hopefully) convert with NTP. In other words, kvmclock is *not* a paravirtualized host-to-guest NTP. Drop the get_kernel_ns() function, that was used both to get the base value of the master clock and to get the current value of kvmclock. The former use is replaced by ktime_get_boot_ns(), the latter is the purpose of get_kernel_ns(). This also allows KVM to provide a Hyper-V time reference counter that is synchronized with the time that is computed from the TSC page. Reviewed-by: NRoman Kagan <rkagan@virtuozzo.com> Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
- 01 4月, 2016 1 次提交
-
-
由 Paolo Bonzini 提交于
If SynIC is disabled, there is nothing that userspace can do to handle these exits; on the other hand, userspace probably will not know about KVM_EXIT_HYPERV_HCALL and complain about it or even exit. Just prevent anything bad from happening by handling the hypercall in KVM and returning an "invalid hypercall" code. Fixes: 83326e43 Cc: Andrey Smetanin <irqlevel@gmail.com> Reviewed-by: NRoman Kagan <rkagan@virtuozzo.com> Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
- 17 2月, 2016 4 次提交
-
-
由 Andrey Smetanin 提交于
The patch implements KVM_EXIT_HYPERV userspace exit functionality for Hyper-V VMBus hypercalls: HV_X64_HCALL_POST_MESSAGE, HV_X64_HCALL_SIGNAL_EVENT. Changes v3: * use vcpu->arch.complete_userspace_io to setup hypercall result Changes v2: * use KVM_EXIT_HYPERV for hypercalls Signed-off-by: NAndrey Smetanin <asmetanin@virtuozzo.com> Reviewed-by: NRoman Kagan <rkagan@virtuozzo.com> CC: Gleb Natapov <gleb@kernel.org> CC: Paolo Bonzini <pbonzini@redhat.com> CC: Joerg Roedel <joro@8bytes.org> CC: "K. Y. Srinivasan" <kys@microsoft.com> CC: Haiyang Zhang <haiyangz@microsoft.com> CC: Roman Kagan <rkagan@virtuozzo.com> CC: Denis V. Lunev <den@openvz.org> CC: qemu-devel@nongnu.org Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
由 Andrey Smetanin 提交于
Currently we do not support Hyper-V hypercall continuation so reject it. Signed-off-by: NAndrey Smetanin <asmetanin@virtuozzo.com> Reviewed-by: NRoman Kagan <rkagan@virtuozzo.com> CC: Gleb Natapov <gleb@kernel.org> CC: Paolo Bonzini <pbonzini@redhat.com> CC: Joerg Roedel <joro@8bytes.org> CC: "K. Y. Srinivasan" <kys@microsoft.com> CC: Haiyang Zhang <haiyangz@microsoft.com> CC: Roman Kagan <rkagan@virtuozzo.com> CC: Denis V. Lunev <den@openvz.org> CC: qemu-devel@nongnu.org Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
由 Andrey Smetanin 提交于
Pass the return code from kvm_emulate_hypercall on to the caller, in order to allow it to indicate to the userspace that the hypercall has to be handled there. Also adjust all the existing code paths to return 1 to make sure the hypercall isn't passed to the userspace without setting kvm_run appropriately. Signed-off-by: NAndrey Smetanin <asmetanin@virtuozzo.com> Reviewed-by: NRoman Kagan <rkagan@virtuozzo.com> CC: Gleb Natapov <gleb@kernel.org> CC: Paolo Bonzini <pbonzini@redhat.com> CC: Joerg Roedel <joro@8bytes.org> CC: "K. Y. Srinivasan" <kys@microsoft.com> CC: Haiyang Zhang <haiyangz@microsoft.com> CC: Roman Kagan <rkagan@virtuozzo.com> CC: Denis V. Lunev <den@openvz.org> CC: qemu-devel@nongnu.org Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
由 Andrey Smetanin 提交于
Rename HV_X64_HV_NOTIFY_LONG_SPIN_WAIT by HVCALL_NOTIFY_LONG_SPIN_WAIT, so the name is more consistent with the other hypercalls. Signed-off-by: NAndrey Smetanin <asmetanin@virtuozzo.com> Reviewed-by: NRoman Kagan <rkagan@virtuozzo.com> CC: Gleb Natapov <gleb@kernel.org> CC: Paolo Bonzini <pbonzini@redhat.com> CC: Joerg Roedel <joro@8bytes.org> CC: "K. Y. Srinivasan" <kys@microsoft.com> CC: Haiyang Zhang <haiyangz@microsoft.com> CC: Roman Kagan <rkagan@virtuozzo.com> CC: Denis V. Lunev <den@openvz.org> CC: qemu-devel@nongnu.org [Change name, Andrey used HV_X64_HCALL_NOTIFY_LONG_SPIN_WAIT. - Paolo] Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
- 09 1月, 2016 6 次提交
-
-
由 Andrey Smetanin 提交于
Trace the following Hyper SynIC timers events: * periodic timer start * one-shot timer start * timer callback * timer expiration and message delivery result * timer config setup * timer count setup * timer cleanup Signed-off-by: NAndrey Smetanin <asmetanin@virtuozzo.com> CC: Gleb Natapov <gleb@kernel.org> CC: Paolo Bonzini <pbonzini@redhat.com> CC: Roman Kagan <rkagan@virtuozzo.com> CC: Denis V. Lunev <den@openvz.org> CC: qemu-devel@nongnu.org Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
由 Andrey Smetanin 提交于
Trace the following Hyper SynIC events: * set msr * set sint irq * ack sint * sint irq eoi Signed-off-by: NAndrey Smetanin <asmetanin@virtuozzo.com> CC: Gleb Natapov <gleb@kernel.org> CC: Paolo Bonzini <pbonzini@redhat.com> CC: Roman Kagan <rkagan@virtuozzo.com> CC: Denis V. Lunev <den@openvz.org> CC: qemu-devel@nongnu.org Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
由 Andrey Smetanin 提交于
Consolidate updating the Hyper-V SynIC timers in a single place: on guest entry in processing KVM_REQ_HV_STIMER request. This simplifies the overall logic, and makes sure the most current state of msrs and guest clock is used for arming the timers (to achieve that, KVM_REQ_HV_STIMER has to be processed after KVM_REQ_CLOCK_UPDATE). Signed-off-by: NAndrey Smetanin <asmetanin@virtuozzo.com> Reviewed-by: NRoman Kagan <rkagan@virtuozzo.com> CC: Gleb Natapov <gleb@kernel.org> CC: Paolo Bonzini <pbonzini@redhat.com> CC: Roman Kagan <rkagan@virtuozzo.com> CC: Denis V. Lunev <den@openvz.org> CC: qemu-devel@nongnu.org Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
由 Andrey Smetanin 提交于
QEMU zero-inits Hyper-V SynIC vectors. We should allow that, and don't reject zero values if set by the host. Signed-off-by: NAndrey Smetanin <asmetanin@virtuozzo.com> Reviewed-by: NRoman Kagan <rkagan@virtuozzo.com> CC: Gleb Natapov <gleb@kernel.org> CC: Paolo Bonzini <pbonzini@redhat.com> CC: Roman Kagan <rkagan@virtuozzo.com> CC: Denis V. Lunev <den@openvz.org> CC: qemu-devel@nongnu.org Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
由 Andrey Smetanin 提交于
Hypervisor Function Specification(HFS) doesn't require to disable SynIC timer at timer config write if timer->count = 0. So drop this check, this allow to load timers MSR's during migration restore, because config are set before count in QEMU side. Also fix condition according to HFS doc(15.3.1): "It is not permitted to set the SINTx field to zero for an enabled timer. If attempted, the timer will be marked disabled (that is, bit 0 cleared) immediately." Signed-off-by: NAndrey Smetanin <asmetanin@virtuozzo.com> Reviewed-by: NRoman Kagan <rkagan@virtuozzo.com> CC: Gleb Natapov <gleb@kernel.org> CC: Paolo Bonzini <pbonzini@redhat.com> CC: Roman Kagan <rkagan@virtuozzo.com> CC: Denis V. Lunev <den@openvz.org> CC: qemu-devel@nongnu.org Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-
由 Andrey Smetanin 提交于
Split stimer_expiration() into two parts - timer expiration message sending and timer restart/cleanup based on timer state(config). This also fixes a bug where a one-shot timer message whose delivery failed once would get lost for good. Signed-off-by: NAndrey Smetanin <asmetanin@virtuozzo.com> Reviewed-by: NRoman Kagan <rkagan@virtuozzo.com> CC: Gleb Natapov <gleb@kernel.org> CC: Paolo Bonzini <pbonzini@redhat.com> CC: Roman Kagan <rkagan@virtuozzo.com> CC: Denis V. Lunev <den@openvz.org> CC: qemu-devel@nongnu.org Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
-