Add support for the titan board.
Signed-off-by: NJamie Lenehan <lenehan@twibble.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

A synco is needed before we jump to start_kernel().

While we're at it, also move the sh_cpu_init() jump until after
we've zeroed BSS, as this has caused some undesirable results
in sh_cpu_init().
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Currently when making changes to control registers, we
typically need some time for changes to take effect (8
nops, generally).  However, for sh4a we simply need to
do an icbi..

This is a simple patch for implementing a general purpose
ctrl_barrier() which functions as a control register write
barrier. There's some additional documentation in the patch
itself, but it's pretty self explanatory.

There were also some places where we were not doing the
barrier, which didn't seem to have any adverse effects on
legacy parts, but certainly did on sh4a. It's safer to have
the barrier in place for legacy parts as well in these cases,
though this does make flush_tlb_all() more expensive (by an
order of 8 nops).  We can ifdef around the flush_tlb_all()
case for now if it's clear that all legacy parts won't have
a problem with this.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add CPU_HAS_PTEA, refactor some of the cpu flag settings.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds support for the I-O DATA Landisk.
Signed-off-by: Nkogiidena <kogiidena@eggplant.ddo.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Drop virt_to_bus() from sg_dma_address() so libata builds.
While we're at it, move sg_dma_address() and sg_dma_len()
from pci.h to scatterlist.h.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

There's a bug in the Hitachi SuperH csum_partial_copy_generic()
implementation.  If the supplied length is 1 (and several alignment
conditions are met), the function immediately branches to label 4.
However, the assembly at label 4 expects the length to be stored in
register r2.  Since this has not occurred, subsequent behavior is
undefined.

This can cause bad payload checksums in TCP connections.

I've fixed the problem by initializing register r2 prior to the branch
instruction.
Signed-off-by: NOllie Wild <aaw@rincewind.tv>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

We had a pretty interesting oops happening, where copy_user_page()
was down()'ing p3map_sem[] with a bogus offset (particularly, an
offset that hadn't been initialized with sema_init(), due to the
mismatch between cpu_data->dcache.n_aliases and what was assumed
based off of the old CACHE_ALIAS value).

Luckily, spinlock debugging caught this for us, and so we drop
the old hardcoded CACHE_ALIAS for sh4 completely and rely on the
run-time probed cpu_data->dcache.alias_mask. This in turn gets
the p3map_sem[] index right, and everything works again.

While we're at it, also convert to 4-level page tables..
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The syscall table has lagged behind a bit, wire up the new ones..
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

It's defined in <linux/cpumask.h> and log is horribly flooded by
"redefined" messages.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Merge support for SH7770 and SH7780 SH-4A subtypes.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Update oprofile build rules for additional subtypes,
particularly SH7750S/SH7091.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Allow multiple early printk consoles via earlyprintk=.

With this change earlyprintk is no longer enabled by default,
it must be specified on the kernel command line. Optionally
with ,keep to prevent unreg by tty_io.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

SH-2/3/4 are able to prefetch, add support for it..
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Minor sign-extension bug in SH-specific memset()..
Signed-off-by: NToshinobu Sugioka <sugioka@itonet.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Newer SH7760 cuts have a range of acceptable PRR values..
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This reworks some of the SH-4 cache handling code to more easily
accomodate newer-style caches (particularly for the > direct-mapped
case), as well as optimizing some of the old code.
Signed-off-by: NRichard Curnow <richard.curnow@st.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

SH-4A supports 'synco' as a barrier, sprinkle it around
the cache ops as necessary..
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

More of the same, trivial cleanups, and moving options to their
own board-specific Kconfig.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Various cleanups for HS7751RVoIP. Mostly just getting
rid of the old mach.c and splitting codec configuration
in to its own Kconfig.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Update the SH DAC audio driver for the clock framework.
Signed-off-by: NAndriy Skulysh <askulysh@gmail.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

suspend/resume support for hitfb, as well as some other
minor cleanups.
Signed-off-by: NAndriy Skulysh <askulysh@gmail.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

With the I/O rework for hd64461 we're down to a single header,
so move it by itself and get rid of the directory.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

SH7300 has a different TMU_TOCR, make the TMU code work again.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Some of these have suffered some bitrot, and so there is
some degree of dead code that has been left sitting around,
clean it up..
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

We don't support this on SH, so just disable it..
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

For some of the larger sizes we permitted spanning pages
across several PTEs, but this turned out to not be generally
useful. This reverts the sh hugetlbpage interface to something
more sensible using huge pages at single PTE granularity.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Some minor cleanups for the updated consolidated hp6xx
mach-type.
Signed-off-by: NAndriy Skulysh <askulysh@gmail.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

We had quite a bit of whitespace damage, clean most of it up..
Signed-off-by: NStuart Menefy <stuart.menefy@st.com>
Signed-off-by: NArthur Othieno <a.othieno@bluewin.ch>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

These were previously sprinkled in machine_power_off(),
though missed being updated when the rest of the boards
switched over.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

We had a special .stack section in the ld script that
was being used to position r15 initially. This is
nonsensical, as we can just use a THREAD_SIZE offset
from the init_thread_union instead (as every other arch
does).
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

in_nmi shifted down a few labels, so we were inadvertently
clearing the lower byte of do_syscall_trace, badness ensues.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Move the syscall table in to its own file, as per sh64. The entry.S
bits will end up being considerably different in the sh2/sh2a cases,
so this lets us keep things in sync somewhat..
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Fix use of uninitialized spinlocks, caught with spinlock debugging..
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

flush_cache_range() wasn't page aligning the end of the range,
we can't assume that it will always be page aligned, and we
ended up getting unaligned faults in some rare call paths.

Additionally, we add a small optimization to just purge the
dcache entirely if the range is large enough that the page
table walking will take longer. We use an arbitrary value of
64 pages for the large range size, as per sh64.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

We didn't have one of these before, a simple implementation
borrowed from MIPS as well as the __HAVE_ARCH_CMPXCHG bits.
Signed-off-by: NTom Rini <trini@kernel.crashing.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

SystemH needs this header as well, not just 770x SE.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6: (225 commits)
  [PATCH] Don't set calgary iommu as default y
  [PATCH] i386/x86-64: New Intel feature flags
  [PATCH] x86: Add a cumulative thermal throttle event counter.
  [PATCH] i386: Make the jiffies compares use the 64bit safe macros.
  [PATCH] x86: Refactor thermal throttle processing
  [PATCH] Add 64bit jiffies compares (for use with get_jiffies_64)
  [PATCH] Fix unwinder warning in traps.c
  [PATCH] x86: Allow disabling early pci scans with pci=noearly or disallowing conf1
  [PATCH] x86: Move direct PCI scanning functions out of line
  [PATCH] i386/x86-64: Make all early PCI scans dependent on CONFIG_PCI
  [PATCH] Don't leak NT bit into next task
  [PATCH] i386/x86-64: Work around gcc bug with noreturn functions in unwinder
  [PATCH] Fix some broken white space in ia32_signal.c
  [PATCH] Initialize argument registers for 32bit signal handlers.
  [PATCH] Remove all traces of signal number conversion
  [PATCH] Don't synchronize time reading on single core AMD systems
  [PATCH] Remove outdated comment in x86-64 mmconfig code
  [PATCH] Use string instructions for Core2 copy/clear
  [PATCH] x86: - restore i8259A eoi status on resume
  [PATCH] i386: Split multi-line printk in oops output.
  ...

* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (47 commits)
  Driver core: Don't call put methods while holding a spinlock
  Driver core: Remove unneeded routines from driver core
  Driver core: Fix potential deadlock in driver core
  PCI: enable driver multi-threaded probe
  Driver Core: add ability for drivers to do a threaded probe
  sysfs: add proper sysfs_init() prototype
  drivers/base: check errors
  drivers/base: Platform notify needs to occur before drivers attach to the device
  v4l-dev2: handle __must_check
  add CONFIG_ENABLE_MUST_CHECK
  add __must_check to device management code
  Driver core: fixed add_bind_files() definition
  Driver core: fix comments in drivers/base/power/resume.c
  sysfs_remove_bin_file: no return value, dump_stack on error
  kobject: must_check fixes
  Driver core: add ability for devices to create and remove bin files
  Class: add support for class interfaces for devices
  Driver core: create devices/virtual/ tree
  Driver core: add device_rename function
  Driver core: add ability for classes to handle devices properly
  ...

Convert cmm's usage of kernel_thread to kthread_run.  Also create the
cmmthread at module load time, so it is possible to check if creation of
the thread fails.

In addition the cmmthread now gets terminated when the module gets unloaded
instead of leaving a stale kernel thread.  Also check the return values of
other registration functions at module load and handle their return values
appropriately.

Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>