This also reduces the cruft of printing scan event
names in capitals.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The 10.x and main firmware branches have
conflicting WMI service bitmap definitions.

This also fixes WMI services parsing on big-endian
hosts and changes debugfs output to be more human
friendly.

kvalo: remove braces and the last semicolon from SVCSTR()
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This converts a driver in drivers/net/* to use the
module_usb_driver() macro which makes the code smaller and a
bit simpler.
Signed-off-by: NHimangi Saraogi <himangi774@gmail.com>
Acked-by: NJulia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Adds the spectral scan feature for ath10k. The spectral scan is triggered by
configuring a mode through a debugfs control file. Samples can be gathered via
another relay debugfs file.

Essentially, to try it out:

ip link set dev wlan0 up
echo background > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
echo trigger > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
iw dev wlan0 scan
echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
cat /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan0 > samples

This feature is still experimental. Based on the original RFC patch of
Sven Eckelmann.
Signed-off-by: NSimon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The ath9k and ath10k will share the definitions of the debugfs spectral
structures and enums. Having them in the same place helps to avoid conflicts.
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NSimon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In some cases during heavy tx vdev stop-start
would timeout on vdev synchronization causing
traffic to stall for a few seconds.

Instead of stop-starting use a dedicated vdev
restart command and down vdevs explicitly before
doing so.

This gets rid of the synchronization
warnings/timeouts and makes channel switching
smoother during traffic.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Print sequence number, AMSDU_MORE flag and AC when additional
debug enabled in RX path. This is usefull for debugging purpose.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

A-MSDU 4addr frames weren't reconstructed properly
and in some cases this resulted in a warning:

 br0: received packet on wlan0.sta1 with own address as source address

Since this was only related to A-MSDU it would
trigger when more intense traffic was generated.
Reported-by: NVu Hai NGUYEN <vh.nguyen@actiasodielec.fr>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The 10.2 firmware is a successor of 10.1 firmware
(formerly identified as 10.x). Both share a lot
but have some slight ABI differences that need to
be taken care of.

The 10.2 firmware introduces some new features but
those can be added in subsequent patches. This
patch makes ath10k boot and work with 10.2 with
comparable functionality to 10.1.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Different firmware may support different numbers of
vdevs.  Use value that is always out of range for all
firmware.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In case of A-MSDU RX we should check attention flags
correctly to be sure we report correct FCS status for
A-MSDU subframes. Without a patch we could report A-MSDU
subframes with wrong FCS as a correct to the stack, next
get a lot of DUP ACK TCP packets. Finally TP drop is seen
and this drop depends on FCS errors ratio for A-MSDU frame.

Example test case when TP drop is seen:
- ath10k configured as an AP
- used ath10k station
- forced A-MSDU (7 frames) on STA
- other traffic on channel (often FCS errors)
- monitor iface added on AP
- TCP STA -> AP traffic (iperf)

a) Iperf logs for case without the patch:

echo "1 64" > htt_max_amsdu_ampdu // disable A-MSDU
[ ID] Interval       Transfer     Bandwidth
[  3]  0.0- 5.0 sec  56.6 MBytes  95.0 Mbits/sec
[  3]  5.0-10.0 sec  60.4 MBytes   101 Mbits/sec
[  3] 10.0-15.0 sec  60.2 MBytes   101 Mbits/sec
[  3] 15.0-20.0 sec  60.2 MBytes   101 Mbits/sec
[  3] 20.0-25.0 sec  63.8 MBytes   107 Mbits/sec
[  3] 25.0-30.0 sec  64.9 MBytes   109 Mbits/sec

echo "7 64" > htt_max_amsdu_ampdu  // set 7 A-MSDU subframes
[  3] 30.0-35.0 sec  40.0 MBytes  67.1 Mbits/sec
[  3] 35.0-40.0 sec  35.9 MBytes  60.2 Mbits/sec
[  3] 40.0-45.0 sec  36.9 MBytes  61.9 Mbits/sec
[  3] 45.0-50.0 sec  37.9 MBytes  63.5 Mbits/sec
[  3] 50.0-55.0 sec  34.5 MBytes  57.9 Mbits/sec
[  3] 55.0-60.0 sec  25.4 MBytes  42.6 Mbits/sec
[  3] 60.0-65.0 sec  48.2 MBytes  81.0 Mbits/sec
[  3] 65.0-70.0 sec  28.8 MBytes  48.2 Mbits/sec
[  3] 70.0-75.0 sec  29.2 MBytes  49.1 Mbits/sec
[  3] 75.0-80.0 sec  22.9 MBytes  38.4 Mbits/sec
[  3] 80.0-85.0 sec  26.4 MBytes  44.2 Mbits/sec
[  3] 85.0-90.0 sec  31.5 MBytes  52.8 Mbits/sec

b) Iperf logs for case with patch:

echo "1 64" > htt_max_amsdu_ampdu // disable A-MSDU
[  3] local 192.168.12.2 port 57512 connected with 192.168.12.1 port 5001
[ ID] Interval       Transfer     Bandwidth
[  3]  0.0- 5.0 sec  60.8 MBytes   102 Mbits/sec
[  3]  5.0-10.0 sec  62.2 MBytes   104 Mbits/sec
[  3] 10.0-15.0 sec  60.9 MBytes   102 Mbits/sec

echo "7 64" > htt_max_amsdu_ampdu  // set 7 A-MSDU subframes
[  3] 15.0-20.0 sec  68.1 MBytes   114 Mbits/sec
[  3] 20.0-25.0 sec  80.5 MBytes   135 Mbits/sec
[  3] 25.0-30.0 sec  83.0 MBytes   139 Mbits/sec
[  3] 30.0-35.0 sec  79.1 MBytes   133 Mbits/sec
[  3] 35.0-40.0 sec  77.1 MBytes   129 Mbits/sec
[  3] 40.0-45.0 sec  77.4 MBytes   130 Mbits/sec
Reported-by: NDenton Gentry <denton.gentry@gmail.com>
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The 10.x firmware does not support IBSS mode at
all. It can't beacon and it crashes when trying to
scan.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware doesn't perform Rx reordering so it is
left to the host driver to do that.

Use mac80211 to perform reordering instead of
re-inventing the wheel.

This fixes TCP throughput issues in some
environments.
Reported-by: NDenton Gentry <denton.gentry@gmail.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This has been tested on 14e4:4328 (BCM4321), 14e4:432b (BCM4322),
14e4:4353 (BCM43224) and 14e4:4359 (BCM43228) which is an almost
complete list of 5 GHz capable device (only BCM43222 is missing).
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We don't have all needed channel tables due to RE process for this
device.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This process requires sending some sample tone, so make sure we're
allowed to transmit first.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

So far we were assuming only A-PHY supports 5 GHz.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The dividend in do_div() is expected to be an unsigned 64-bit integer,
which leads to the following warning when building for 32-bit MIPS:

  drivers/net/wireless/mac80211_hwsim.c: In function 'mac80211_hwsim_set_tsf':
  drivers/net/wireless/mac80211_hwsim.c:664:98: warning: comparison of distinct pointer types lacks a cast [enabled by default]
    data->bcn_delta = do_div(delta, bcn_int);

Since we care about the signedness of delta when adjusting tsf_offset
and bcm_delta, use the absolute value for the division and compare
the two timestamps to determine the sign.
Signed-off-by: NAndrew Bresticker <abrestic@chromium.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The DCM condition was not checked well for channel switch in both AP and
station scenarios. Teardown was also not done for AP/GO DCM. Add the
missing checks.
Reported-by: NPeer, Ilan <ilan.peer@intel.com>
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

It was possible to enter an endless loop while
processing a single pci copy engine pipe. This
could effectively render ath10k incapable of
responding to any requests.

An example case when this could happen is when
firmware generates a lot of events, e.g. spectral
scan phyerr via WMI.
Reported-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Some radios may share the same ID and revision but differ by a version.
E.g. radio in BCM5357B0 is version 1 and requires specific handling.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Newer devices need different workarounds for cores 0 and 1.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add some missing ops and prepare for new devices support. This patch is
a great stability improvement for BCM43217. Earlier Tenda W322E used to
disconnect every 2 minutes (16 times over 30 minutes). With this fix I
got it running for 4 hours (with iperf) without any disconnection.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes handling channel 14 and adds code for BCM43217.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mmc_rescan will scan for non-removable cards only once, hence the card
will not be rediscovered.
Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Acked-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the firmware asserts, we restart the device and reset
the relevant data we hold in the driver. BT Coex data was
not reset and because of that, the driver wouldn't
reconfigure the firmware properly after firmware restart.
Same for beacon filtering. Fix that.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When we associate, we may have heard the beacon before the
association. In that case, BSS_CHANGED_BEACON_INFO will be
set along with BSS_CHANGED_ASSOC in changes in
bss_info_change.

In this case, we didn't update the smart fifo nor beacon
filtering leaving those two feature disabled.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add the Control Status Registers to the firmware error dump
infrastructure.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Use the fw-error-dump infrastructure to dump the periphery
registers. Only certain ranges are readable, so dump only
these.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The mvm op_mode won't allocate the buffer for the transport
any more. The transport allocates its own buffer and mvm
is in charge of splicing the buffers in the debugfs hook.

This makes the repartition easier to handle.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

modinfo and kerneldoc disagreed on the meaning of this field.
Reported-by: NAndrea Oliveri <oliveriandrea@gmail.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add OTP to the string: "can't parse empty OTP/NVM section"
NVM usually refers to nvm_file while the problem can be in
the OTP.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The recent unified scan api change introduced issues
when stopping ongoing scans, since both regular and
sched scan now use same stopped notification.

When issuing a new scan right after a running one,
we get the "old" notification and handle it wrongly
as notification for the current scan.

Fix it by introducing a new function that make sure
we consume the pending notifications before issuing
a new scan.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Reviewed-by: NArikX Nemtsov <arik@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Leave it to default instead - regardless of the BT activity.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

According to new requirements, the ACK / CTS kill mask is
not related to reduced TX power anymore. This allows to
remove the code that tracked reduced TX power enablement
across different interfaces.
The ACK / CTS kill mask is now fetch from a table. It
depends on the Activity grading (activity from BT) and on
the Look Up Table (LUT) type.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>