CPU_IDLE=y has been default for ACPI=y since Nov-2007,
and has shipped in many distributions since then.

Here we delete the CPU_IDLE=n ACPI idle code, since
nobody should be using it, and we don't want to
maintain two versions.
Signed-off-by: NLen Brown <len.brown@intel.com>

It is true that BM_RLD needs to be set to enable
bus master activity to wake an older chipset (eg PIIX4) from C3.

This is contrary to the erroneous wording the ACPI 2.0, 3.0
specifications that suggests that BM_RLD is an indicator
rather than a control bit.

ACPI 1.0's correct wording should be restored in ACPI 4.0:
http://www.acpica.org/bugzilla/show_bug.cgi?id=689

But the kernel should not have to clear BM_RLD
when entering a non C3-type state just to set
it again when entering a C3-type C-state.

We should be able to set BM_RLD at boot time
and leave it alone -- removing the overhead of
accessing this IO register from the idle entry path.
Signed-off-by: NLen Brown <len.brown@intel.com>

PM1a_STS and PM1b_STS are twins that get OR'd together
on reads, and all writes are repeated to both.

The fields in PM1x_STS are single bits only,
there are no multi-bit fields.

So it is not necessary to lock PM1x_STS reads against
writes because it is impossible to read an intermediate
value of a single bit.  It will either be 0 or 1,
even if a write is in progress during the read.
Reads are asynchronous to writes no matter if a lock
is used or not.
Signed-off-by: NLen Brown <len.brown@intel.com>

While looking at reducing the amount of architecture namespace pollution
in the generic kernel, I found that asm/irq.h is included in the vast
majority of compilations on ARM (around 650 files.)

Since asm/irq.h includes a sub-architecture include file on ARM, this
causes a negative impact on the ccache's ability to re-use the build
results from other sub-architectures, so we have a desire to reduce the
dependencies on asm/irq.h.

It turns out that a major cause of this is the needless include of
linux/hardirq.h into asm-generic/local.h.  The patch below removes this
include, resulting in some 250 to 300 files (around half) of the kernel
then omitting asm/irq.h.

My test builds still succeed, provided two ARM files are fixed
(arch/arm/kernel/traps.c and arch/arm/mm/fault.c) - so there may be
negative impacts for this on other architectures.

Note that x86 does not include asm/irq.h nor linux/hardirq.h in its
asm/local.h, so this patch can be viewed as bringing the generic version
into line with the x86 version.

[kosaki.motohiro@jp.fujitsu.com: add #include <linux/irqflags.h> to acpi/processor_idle.c]
[adobriyan@gmail.com: fix sparc64]
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Impact: reward non-stop TSCs with good TSC-based clocksources, etc.

Add support for CPUID_0x80000007_Bit8 on Intel CPUs as well. This bit means
that the TSC is invariant with C/P/T states and always runs at constant
frequency.

With Intel CPUs, we have 3 classes
* CPUs where TSC runs at constant rate and does not stop n C-states
* CPUs where TSC runs at constant rate, but will stop in deep C-states
* CPUs where TSC rate will vary based on P/T-states and TSC will stop in deep
  C-states.

To cover these 3, one feature bit (CONSTANT_TSC) is not enough. So, add a
second bit (NONSTOP_TSC). CONSTANT_TSC indicates that the TSC runs at
constant frequency irrespective of P/T-states, and NONSTOP_TSC indicates
that TSC does not stop in deep C-states.

CPUID_0x8000000_Bit8 indicates both these feature bit can be set.
We still have CONSTANT_TSC _set_ and NONSTOP_TSC _not_set_ on some older Intel
CPUs, based on model checks. We can use TSC on such CPUs for time, as long as
those CPUs do not support/enter deep C-states.
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Move all the component definitions for drivers to a single shared place,
include/acpi/acpi_drivers.h.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

reflect the actual state entered in dev->last_state, when actaul state entered
is different from intended one.
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Trivial cleanups for ACPI. Fix misspelling in printk(), fix mismerge,
add file header.

AK: removed file header
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

pm_idle_save resp. pm_idle_old can be NULL when the restore code in
acpi_processor_cst_has_changed() resp. cpuidle_uninstall_idle_handler()
is called. This can set pm_idle unconditinally to NULL, which causes the
kernel to panic when calling pm_idle in the x86 idle code. This was
covered by an extra check for !pm_idle in the x86 idle code, which was
removed during the x86 idle code refactoring.

Instead of restoring the pm_idle check in the x86 code prevent the
acpi/cpuidle code to set pm_idle to NULL.

Reported by: Dhaval Giani http://lkml.org/lkml/2008/7/2/309
Based on a debug patch from Ingo Molnar
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The acpi idle waits calls local_irq_save and then uses mwait to go into
idle. The tracer gets reenabled at local_irq_save but does not detect that
the idle allows for wake ups.

This patch adds code to disable the tracing when acpi puts the CPU to idle.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

"idle=nomwait" disables the use of the MWAIT
instruction from both C1 (C1_FFH) and deeper (C2C3_FFH)
C-states.

When MWAIT is unavailable, the BIOS and OS generally
negotiate to use the HALT instruction for C1,
and use IO accesses for deeper C-states.

This option is useful for power and performance
comparisons, and also to work around BIOS bugs
where broken MWAIT support is advertised.

http://bugzilla.kernel.org/show_bug.cgi?id=10807
http://bugzilla.kernel.org/show_bug.cgi?id=10914Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NLi Shaohua <shaohua.li@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

"idle=halt" limits the idle loop to using
the halt instruction.  No MWAIT, no IO accesses,
no C-states deeper than C1.

If something is broken in the idle code,
"idle=halt" is a less severe workaround
than "idle=poll" which disables all power savings.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

Change processors from an array sized by NR_CPUS to a per_cpu variable.
Signed-off-by: NMike Travis <travis@sgi.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

It's never used and the comments refer to nonatomic and retry
interchangably. So get rid of it.
Acked-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

cpuidle and acpi driver interaction bug with the way cpuidle_register_driver()
is called. Due to this bug, there will be oops on
AC<->DC on some systems, where they support C-states in one DC and not in AC.

The current code does
ON BOOT:
	Look at CST and other C-state info to see whether more than C1 is
	supported. If it is, then acpi processor_idle does a
	cpuidle_register_driver() call, which internally enables the device.

ON CST change notification (AC<->DC) and on suspend-resume:
	acpi driver temporarily disables device, updates the device with
	any new C-states, and reenables the device.

The problem is is on boot, there are no C2, C3 states supported and we skip
the register. Later on AC<->DC, we may get a CST notification and we try
to reevaluate CST and enabled the device, without actually registering it.
This causes breakage as we try to create /sys fs sub directory, without the
parent directory which is created at register time.

Thanks to Sanjeev for reporting the problem here.
http://bugzilla.kernel.org/show_bug.cgi?id=10394Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

acpi_processor_idle and "idle=" boot parameter interaction is broken.
The problem is that, at boot time acpi driver is checking for "idle=" boot
option and not registering the acpi idle handler. But, when there is a CST
changed callback (typically when switching AC <-> battery or suspend-resume)
there are no checks for boot_option_idle_override and acpi idle handler tries
to get installed with nasty side effects.

With CPU_IDLE configured this issue causes results in a nasty oops on CST
change callback and without CPU_IDLE there is no oops, but boot option
of "idle=" gets ignored and acpi idle handler gets installed.

Change the behavior to not do anything in acpi idle handler when there is a
"idle=" boot option.

Note that the problem is only there when "idle=" boot option is used.
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Use proc_create()/proc_create_data() to make sure that ->proc_fops and ->data
be setup before gluing PDE to main tree.

Add correct ->owner to proc_fops to fix reading/module unloading race.
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

OK, so 25-mm1 gave a lockdep error which made me look into this.

The first thing that I noticed was the horrible mess; the second thing I
saw was hacks like: 71e93d15

The problem is that arch idle routines are somewhat inconsitent with
their IRQ state handling and instead of fixing _that_, we go paper over
the problem.

So the thing I've tried to do is set a standard for idle routines and
fix them all up to adhere to that. So the rules are:

  idle routines are entered with IRQs disabled
  idle routines will exit with IRQs enabled

Nearly all already did this in one form or another.

Merge the 32 and 64 bit bits so they no longer have different bugs.

As for the actual lockdep warning; __sti_mwait() did a plainly un-annotated
irq-enable.
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Patch to fix huge number of wakeups reported due to recent changes in
processor_idle.c. The problem was that the entry_method determination was
broken due to one of the recent commits (bc71bec9) causing
C1 entry to not to go to halt.

http://lkml.org/lkml/2008/3/22/124Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

commit 9b12e18c
'ACPI: cpuidle: Support C1 idle time accounting'
was implicated in a 100% C0 idle regression.
http://bugzilla.kernel.org/show_bug.cgi?id=10076

It pointed out a potential problem where the menu governor
may get confused by the C-state residency time from poll
idle or C1 idle, where this timing info is not accurate.
This inaccuracy is due to interrupts being handled
before we account for C-state exit.

Do not mark TIME_VALID for CO poll state.
Mark C1 time as valid only with the MWAIT (CSTATE_FFH) entry method.

This makes governors use the timing information only when it is correct and
eliminates any wrong policy decisions that may result from invalid timing
information.
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

This original patch
http://ussg.iu.edu/hypermail/linux/kernel/0712.2/1451.html
was intending to add acpi_unlazy_tlb() to acpi_idle_enter_bm(),
which is used for C3 entry.

But it was merged incorrectly as commmit

bde6f5f5
'x86: voluntary leave_mm before entering ACPI C3'

so the call was instead added to acpi_idle_enter_simple()
(which is C2 entry routine), probably due to identical
context in that function.

Move the call back to acpi_idle_enter_bm().
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

This avoids the harmless WARNING by lockdep in acpi_processor_idle().

The reason for WARNING is because at the depth of idle handling code,
some of the idle handlers disable interrupts, some times, while returning from
the idle handler. After return, acpi_processor_idle and few other routines
in the file did an unconditional local_irq_enable(). With LOCKDEP, enabling
irq when it is already enabled generates the below WARNING.

> > [    0.593038] ------------[ cut here ]------------
> > [    0.593267] WARNING: at kernel/lockdep.c:2035 trace_hardirqs_on+0xa0/0x115()
> > [    0.593596] Modules linked in:
> > [    0.593756] Pid: 0, comm: swapper Not tainted 2.6.25-rc5 #8
> > [    0.594017]
> > [    0.594017] Call Trace:
> > [    0.594216]  [<ffffffff80231663>] warn_on_slowpath+0x58/0x6b
> > [    0.594495]  [<ffffffff80495966>] ? _spin_unlock_irqrestore+0x38/0x47
> > [    0.594809]  [<ffffffff80329a86>] ? acpi_os_release_lock+0x9/0xb
> > [    0.595103]  [<ffffffff80337840>] ? acpi_set_register+0x161/0x173
> > [    0.595401]  [<ffffffff8034c8d4>] ? acpi_processor_idle+0x1de/0x546
> > [    0.595706]  [<ffffffff8020a23b>] ? default_idle+0x0/0x73
> > [    0.595970]  [<ffffffff8024fc0e>] trace_hardirqs_on+0xa0/0x115
> > [    0.596049]  [<ffffffff8034c6f6>] ? acpi_processor_idle+0x0/0x546
> > [    0.596346]  [<ffffffff8034c8d4>] acpi_processor_idle+0x1de/0x546
> > [    0.596642]  [<ffffffff8020a23b>] ? default_idle+0x0/0x73
> > [    0.596912]  [<ffffffff8034c6f6>] ? acpi_processor_idle+0x0/0x546
> > [    0.597209]  [<ffffffff8020a23b>] ? default_idle+0x0/0x73
> > [    0.597472]  [<ffffffff8020a355>] cpu_idle+0xa7/0xd1
> > [    0.597717]  [<ffffffff80485fa1>] rest_init+0x55/0x57
> > [    0.597957]  [<ffffffff8062fb49>] start_kernel+0x29d/0x2a8
> > [    0.598215]  [<ffffffff8062f1da>] _sinittext+0x1da/0x1e1
> > [    0.598464]
> > [    0.598546] ---[ end trace 778e504de7e3b1e3 ]---
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

TSC is used even on machines when CONFIG_X86_TSC is not set (X86_TSC
means _require_ TSC), but it is not properly disabled when it is
unusable, because ACPI code understood the config switch as "may use
TSC".

This actually fixes suspend problems on my x60.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NLen Brown <len.brown@intel.com>

Add a new sysfs entry under cpuidle states. desc - can be used by driver to
communicate to userspace any specific information about the state.
This helps in identifying the exact hardware C-states behind the ACPI C-state
definition.

Idea is to export this through powertop, which will help to map the C-state
reported by powertop to actual hardware C-state.
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Earlier patch (bc71bec9) broke
suspend resume on many laptops. The problem was reported by
Carlos R. Mafra and Calvin Walton, who bisected the issue to above patch.

The problem was because, C2 and C3 code were calling acpi_idle_enter_c1
directly, with C2 or C3 as state parameter, while suspend/resume was in
progress. The patch bc71bec9 started making use of that state information,
assuming that it would always be referring to C1 state. This caused the
problem with suspend-resume as we ended up using C2/C3 state indirectly.

Fix this by adding acpi_idle_suspend check in enter_c1.
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Add a default poll idle state with 0 latency. Provides an option to users
to use poll_idle by using 0 as the latency requirement.
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Show C1 idle time in /sysfs cpuidle interface. C1 idle time may not
be entirely accurate in all cases. It includes the time spent
in the interrupt handler after wakeup with "hlt" based C1. But, it will
be accurate with "mwait" based C1.
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Add MWAIT idle for C1 state instead of halt, on platforms that support
C1 state with MWAIT.

Renames cx->space_id to something more appropriate.
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

acpi_safe_halt() needs interrupts to be disabled for atomic
need_resched check and safe halt. Otherwise we may miss an
interrupt and go into halt.

acpi_safe_halt() also does not enable interrupts on all return paths.

So the callers should handle enable and disable interrupts around it.
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Replace latency.c use with pm_qos_params use.
Signed-off-by: Nmark gross <mgross@linux.intel.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The ACPI code currently disables TSC use in any C2 and C3
states. But the AMD Fam10h BKDG documents that the TSC
will never stop in any C states when the CONSTANT_TSC bit is
set. Make this disabling conditional on CONSTANT_TSC
not set on AMD.

I actually think this is true on Intel too for C2 states
on CPUs with p-state invariant TSC, but this needs
further discussions with Len to really confirm :-)

So far it is only enabled on AMD.

Cc: lenb@kernel.org
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Aviod TLB flush IPIs during C3 states by voluntary leave_mm()
before entering C3.

The performance impact of TLB flush on C3 should not be significant with
respect to C3 wakeup latency. Also, CPUs tend to flush TLB in hardware while in
C3 anyways.

On a 8 logical CPU system, running make -j2, the number of tlbflush IPIs goes
down from 40 per second to ~ 0. Total number of interrupts during the run
of this workload was ~1200 per second, which makes it ~3% savings in wakeups.

There was no measurable performance or power impact however.

[ akpm@linux-foundation.org: symbol export fixes. ]
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

This was writeable in 2.6.23 but the cpuidle merge made it read-only.  But
some people's scripts (ie: Mark's) were writing to it.

As an unhappy compromise, make max_cstate writeable again if the kernel was
configured without CONFIG_CPU_IDLE.

http://bugzilla.kernel.org/show_bug.cgi?id=9683Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Mark Lord <lkml@rtr.ca>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

More aggressively request deep C-states.

Note that the job of the OS is to minimize latency
impact to expected break events such as interrupts.

It is not the job of the OS to try to calculate if
the C-state will reach energy break-even.
The platform doesn't give the OS enough information
for it to make that calculation.  Thus, it is up
to the platform to decide if it is worth it to
go as deep as the OS requested it to, or if it
should internally demote to a more shallow C-state.

But the converse is not true.  The platform can not
promote into a deeper C-state than the OS requested
else it may violate latency constraints.  So it is
important that the OS be aggressive in giving the
platform permission to enter deep C-states.
Signed-off-by: NLen Brown <len.brown@intel.com>

Start with default value of 6, so by default,
there is no functional change in this patch.
Signed-off-by: NLen Brown <len.brown@intel.com>

The timer broadcast code might access HPET, which should not be
accessed after the busmaster disable.

In acpi_idle_enter_simple() this change also prevents, that we modify
the busmaster state without going actually idle. This might leave the
ACPI bm state in a stale state, when we leave the function early in
the need_resched() check.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Acked-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>

AMD Opteron processors before CG revision don't like C-states > 1.

This solves the long standing bugzilla #5303 and probably some more
on affected machines:

  http://bugzilla.kernel.org/show_bug.cgi?id=5303

[ tglx@linutronix.de: reworked the patch so it does not wreck ia64 ]
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Fix for http://bugzilla.kernel.org/show_bug.cgi?id=9355

cpuidle always used to fallback to C2 if there is some bm activity while
entering C3. But, presence of C2 is not always guaranteed. Change cpuidle
algorithm to detect a safe_state to fallback in case of bm_activity and
use that state instead of C2.
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Port 2aa44d05
(sched: sched_clock_idle_[sleep|wakeup]_event()) to cpuidle.
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Port 18eab855
(Enable C3 even when PM2_control is zero) to cpuidle.

Without this patch, some systems will notice a regression
when enabling CPU_IDLE -- C3 would no longer be available.
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>