An offb machine has been seen in the fields which adds two
offb nodes, so continue scanning the list after removing one.
Signed-off-by: NDave Airlie <airlied@redhat.com>

* 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
  parisc: Set PCI CLS early in boot.

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] Fix broken sn2 build

Set the PCI CLS early in the boot process to prevent
device failures. In pcibios_set_master use the new
pci_cache_line_size instead of a hard-coded value.
Signed-off-by: NCarlos O'Donell <carlos@codesourcery.com>
Reviewed-by: NGrant Grundler <grundler@google.com>
Signed-off-by: NKyle McMartin <kyle@redhat.com>

* 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: Fix out_le32() macro
  microblaze: Fix cache loop function for cache range

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  Revert "block: improve queue_should_plug() by looking at IO depths"

Trailing semicolon causes compilation involving out_le32() to fail.
Signed-off-by: NSteven J. Magnani <steve@digidescorp.com>
Signed-off-by: NMichal Simek <monstr@monstr.eu>

I create wrong asm code but none test shows that this part of code is wrong.
I am not convinces that were good idea to create asm optimized macros
for caches. The reason is that there is not optimization with previous code
that's why make sense to add old code and do some benchmarking which
functions are faster.
Signed-off-by: NMichal Simek <monstr@monstr.eu>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  net: bug fix for vlan + gro issue
  tc35815: Remove a wrong netif_wake_queue() call which triggers BUG_ON
  cdc_ether: new PID for Ericsson C3607w to the whitelist (resubmit)
  IPv6: better document max_addresses parameter
  MAINTAINERS: update mv643xx_eth maintenance status
  e1000: Fix DMA mapping error handling on RX
  iwlwifi: sanity check before counting number of tfds can be free
  iwlwifi: error checking for number of tfds in queue
  iwlwifi: set HT flags after channel in rxon

Traffic (tcp) doesnot start on a vlan interface when gro is enabled.
Even the tcp handshake was not taking place.
This is because, the eth_type_trans call before the netif_receive_skb
in napi_gro_finish() resets the skb->dev to napi->dev from the previously
set vlan netdev interface. This causes the ip_route_input to drop the
incoming packet considering it as a packet coming from a martian source.

I could repro this on 2.6.32.7 (stable) and 2.6.33-rc7.
With this fix, the traffic starts and the test runs fine on both vlan
and non-vlan interfaces.

CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  ACPI: Be in TS_POLLING state during mwait based C-state entry
  ACPI: Fix regression where _PPC is not read at boot even when ignore_ppc=0
  acer-wmi: Respect current backlight level when loading

* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/vmwgfx: Fix queries if no dma buffer thrashing is occuring.
  drm/nv50: fix vram ptes on IGPs to point at stolen system memory
  drm/nv50: fix instmem binding on IGPs to point at stolen system memory
  drm/nv50: improve vram page table construction
  drm/nv50: more efficient clearing of gpu page table entries
  drm/nv50: make nv50_mem_vm_{bind,unbind} operate only on vram
  drm/nouveau: Fix up pre-nv17 analog load detection.

Revert the change made to arch/ia64/sn/kernel/setup.c by commit
204fba4a as it breaks the build.

Fixing the build the b94b0808 way
breaks xpc because genksyms then fails to generate an CRC for
per_cpu____sn_cnodeid_to_nasid because of limitations in the
generic genksyms code.
Signed-off-by: NHedi Berriche <hedi@sgi.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

The netif_wake_queue() is called correctly (i.e. only on !txfull
condition) from txdone routine.  So Unconditional call to the
netif_wake_queue() here is wrong.  This might cause calling of
start_xmit routine on txfull state and trigger BUG_ON.

This bug does not happen when NAPI disabled.  After txdone there
must be at least one free tx slot.  But with NAPI, this is not
true anymore and the BUG_ON can hits on heavy load.

In this driver NAPI was enabled on 2.6.33-rc1 so this is
regression from 2.6.32 kernel.
Reported-by: NRalf Roesch <ralf.roesch@rw-gmbh.de>
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a new vid/pid to the cdc_ether whitelist.

Device added:
- Ericsson Mobile Broadband variant C3607w
Signed-off-by: NTorgny Johansson <torgny.johansson@gmail.com>

--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.htmlSigned-off-by: NDavid S. Miller <davem@davemloft.net>

Andrew Morton wrote:
>> >From ip-sysctl.txt file in kernel documentation I can see following description
>> for max_addresses:
>> max_addresses - INTEGER
>>         Number of maximum addresses per interface.  0 disables limitation.
>>         It is recommended not set too large value (or 0) because it would
>>         be too easy way to crash kernel to allow to create too much of
>>         autoconfigured addresses.
           ^^^^^^^^^^^^^^

>> If this parameter applies only for auto-configured IP addressed, please state
>> it more clearly in docs or rename the parameter to show that it refers to
>> auto-configuration.

It did mention autoconfigured in the text, but the below makes it more obvious.

More clearly document IPv6 max_addresses parameter.
Signed-off-by: NBrian Haley <brian.haley@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I am no longer with Marvell.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check for error return from pci_map_single/pci_map_page and clean up.

With this and the previous patch the driver was able to handle a significant
percentage of errors (I set the fault injection rate to 10% and could still
download large files at a reasonable speed).
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit fb1e7538.

"Benjamin S." <sbenni@gmx.de> reports that the patch in question
causes a big drop in sequential throughput for him, dropping from
200MB/sec down to only 70MB/sec.

Needs to be investigated more fully, for now lets just revert the
offending commit.

Conflicts:

	include/linux/blkdev.h
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Intercept query commands and apply relocations to their guest pointers.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

* 'nouveau/for-airlied' of ../drm-nouveau-next:
  drm/nv50: fix vram ptes on IGPs to point at stolen system memory
  drm/nv50: fix instmem binding on IGPs to point at stolen system memory
  drm/nv50: improve vram page table construction
  drm/nv50: more efficient clearing of gpu page table entries
  drm/nv50: make nv50_mem_vm_{bind,unbind} operate only on vram
  drm/nouveau: Fix up pre-nv17 analog load detection.

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  MIPS: BCM47xx: Fix 128MB RAM support
  MIPS: Highmem: Fix build error

Merge branch 'parisc/tracehook' of git://git.kernel.org/pub/scm/linux/kernel/git/frob/linux-2.6-roland

* 'parisc/tracehook' of git://git.kernel.org/pub/scm/linux/kernel/git/frob/linux-2.6-roland:
  Revert "parisc: HAVE_ARCH_TRACEHOOK"

803bf5ec ("fs/exec.c: restrict initial
stack space expansion to rlimit") attempts to limit the initial stack to
20*PAGE_SIZE.  Unfortunately, in attempting ensure the stack is not
reduced in size, we ended up not changing the stack at all.

This size reduction check is not necessary as the expand_stack call does
this already.

This caused a regression in UML resulting in most guest processes being
killed.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Reviewed-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: NWANG Cong <xiyou.wangcong@gmail.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: James Morris <jmorris@namei.org>
Cc: Serge Hallyn <serue@us.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jouni Malinen <j@w1.fi>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 4410f391 ("fbdev: add support for
handoff from firmware to hw framebuffers") didn't add fb_destroy
operation to efifb.  Fix it and change aperture_size to match size
passed to request_mem_region.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=15151Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Reported-by: NAlex Zhavnerchik <alex.vizor@gmail.com>
Tested-by: NAlex Zhavnerchik <alex.vizor@gmail.com>
Acked-by: NPeter Jones <pjones@redhat.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

geode-mfgpt: restore previous behavior for selecting IRQ

The MFGPT IRQ used to be, in order of decreasing priority,
 * IRQ supplied by the user as a boot-time parameter,
 * IRQ previously set by the BIOS or another driver,
 * default IRQ given at compile time.

Return to this behavior, which got broken when splitting the
MFGPT/clocksource driver for 2.6.33-rc1.
Signed-off-by: NJens Rottmann <JRottmann@LiPPERTEmbedded.de>
Acked-by: NAndres Salomon <dilinger@collabora.co.uk>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is retry of reverted 859ddf09
("idr: fix a critical misallocation bug") which contained two bugs.

* pa[idp->layers] should be cleared even if it's not used by
  sub_alloc() because it's used by mark idr_mark_full().

* The original condition check also assigned pa[l] to p which the new
  code didn't do thus leaving p pointing at the wrong layer.

Both problems have been fixed and the idr code has received good amount
testing using userland testing setup where simple bitmap allocator is
run parallel to verify the result of idr allocation.

The bug this patch fixes is caused by sub_alloc() optimization path
bypassing out-of-room condition check and restarting allocation loop
with starting value higher than maximum allowed value.  For detailed
description, please read commit message of 859ddf09.
Signed-off-by: NTejun Heo <tj@kernel.org>
Based-on-patch-from: Eric Paris <eparis@redhat.com>
Reported-by: NEric Paris <eparis@redhat.com>
Tested-by: NStefan Lippers-Hollmann <s.l-h@gmx.de>
Tested-by: NSerge Hallyn <serue@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

find_task_by_vpid() is not safe without rcu_read_lock().  2.6.33-rc7 got
RCU protection for sys_setpriority() but missed it for sys_getpriority().
Signed-off-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Acked-by: NSerge Hallyn <serue@us.ibm.com>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Presently the oom-killer is memcg aware and it finds the worst process
from processes under memcg(s) in oom.  Then, it kills victim's child
first.

It may kill a child in another cgroup and may not be any help for
recovery.  And it will break the assumption users have.

This patch fixes it.
Signed-off-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: NMinchan Kim <minchan.kim@gmail.com>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Reviewed-by: NDaisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Acked-by: NDavid Rientjes <rientjes@google.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

This also modifies the unused PRAMIN PT entries to be all zeroes, can't
really recall why I used 9/0 initially, just that it didn't work for
some reason.  It was likely masking a bug elsewhere that's since been
fixed.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

This commit changes nouveau to construct PTEs which look very much like
the ones the binary driver creates.

I presume that filling multiple PTEs identically with length flags and
the physical address of the start of a block of VRAM is a hint to the
memory controller that it need not perform additional page table lookups
for that range of addresses.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

GART is handled elsewhere, no reason to have the code for it here too.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Ignoring the last page when ddr size is 128M. Cached accesses to last page
is causing the processor to prefetch using address above 128M stepping out
of the DDR address space.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/981/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>