This factors out the AMD native MMCONFIG discovery so we can use it
outside amd_bus.c.

amd_bus.c reads AMD MSRs so it can remove the MMCONFIG area from the
PCI resources.  We may also need the MMCONFIG information to work
around BIOS defects in the ACPI MCFG table.

Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: stable@kernel.org       # 2.6.34+
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

x86 has two kinds of PCI root bus scanning:

(1) ACPI-based, using _CRS resources.  This used pci_create_bus(), not
    pci_scan_bus(), because ACPI hotplug needed to split the
    pci_bus_add_devices() into a separate host bridge .start() method.

    This patch parses the _CRS resources earlier, so we can build a list of
    resources and pass it to pci_create_root_bus().

    Note that as before, we parse the _CRS even if we aren't going to use
    it so we can print it for debugging purposes.

(2) All other, which used either default resources (ioport_resource and
    iomem_resource) or information read from the hardware via amd_bus.c or
    similar.  This used pci_scan_bus().

    This patch converts x86_pci_root_bus_res_quirks() (previously called
    from pcibios_fixup_bus()) to x86_pci_root_bus_resources(), which builds
    a list of resources before we call pci_scan_root_bus().

    We also use x86_pci_root_bus_resources() if we have ACPI but are
    ignoring _CRS.

CC: Yinghai Lu <yinghai.lu@oracle.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This doesn't change any functionality, but it makes a subsequent patch
slightly simpler.

pci_scan_bus(NULL, ...) and pci_scan_bus_parented() are identical except
that pci_scan_bus() also calls pci_bus_add_devices():

  pci_scan_bus_parented
    pci_create_bus
    pci_scan_child_bus

  pci_scan_bus
    pci_create_bus
    pci_scan_child_bus
    pci_bus_add_devices

All callers of pcibios_scan_root() call pci_bus_add_devices() explicitly,
and we don't pass a parent device, so we might as well use pci_scan_bus().
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

We currently read the CNB20LE aperture information in a PCI quirk,
which happens after we've already created the root bus.  This patch
changes it to read the apertures earlier so we can create the root
bus with the correct resources.

I believe the CNB20LE lives at "pci 0000:00:00" based on
https://lkml.org/lkml/2010/8/13/220

CC: Ira W. Snyder <iws@ovro.caltech.edu>
CC: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Commit 24d9b70b (x86: Use PCI method
for enabling AMD extended config space before MSR method) added a
message when IO access to PCI ECS was enabled via access to the NB_CFG
PCI register.  This can lead to a bogus message like

[    0.365177] Extended Config Space enabled on 0 nodes

which is misleading because IO ECS access is subsequently enabled for
AMD CPUs (that support this) by modifying the corresponding NB_CFG
MSR.

Furthermore it's not "Extended Config Space" that is enabled by this
register setting. It's the IO access that is enabled for extended
configruation space.

IMHO the ambiguous message needs to be cancelled.

Cc: Jan Beulich <jbeulich@novell.com>
Cc: Robert Richter <robert.richter@amd.com>
Signed-off-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This patch removes x86's architecture-specific 'pcibios_set_master()'
routine and lets the default PCI core based implementation handle PCI
device 'latency timer' setup.

No functional change.
Signed-off-by: NMyron Stowe <myron.stowe@redhat.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The 'latency timer' of PCI devices, both Type 0 and Type 1,
is setup in architecture-specific code [see: 'pcibios_set_master()'].
There are two approaches being taken by all the architectures - check
if the 'latency timer' is currently set between 16 and 255 and if not
bring it within bounds, or, do nothing (and then there is the
gratuitously different PA-RISC implementation).

There is nothing architecture-specific about PCI's 'latency timer' so
this patch pulls its setup functionality up into the PCI core by
creating a generic 'pcibios_set_master()' function using the '__weak'
attribute which can be used by all architectures as a default which,
if necessary, can then be over-ridden by architecture-specific code.

No functional change.
Signed-off-by: NMyron Stowe <myron.stowe@redhat.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This assures that a _CRS reserved host bridge window or window region is
not used if it is not addressable by the CPU.  The new code either trims
the window to exclude the non-addressable portion or totally ignores the
window if the entire window is non-addressable.

The current code has been shown to be problematic with 32-bit non-PAE
kernels on systems where _CRS reserves resources above 4GB.
Signed-off-by: NGary Hade <garyhade@us.ibm.com>
Reviewed-by: NBjorn Helgaas <bhelgaas@google.com>
Cc: Thomas Renninger <trenn@novell.com>
Cc: linux-kernel@vger.kernel.org
Cc: stable@kernel.org
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Enabling CRS by default breaks suspend on the Thinkpad SL510.
Details in https://bugzilla.redhat.com/show_bug.cgi?id=769657Reported-by: NStefan Kirrmann <stefan.kirrmann@gmail.com>
Signed-off-by: NDave Jones <davej@redhat.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The Dell Studio 1557 also doesn't suspend correctly when CRS is enabled.
Details at https://bugzilla.redhat.com/show_bug.cgi?id=769657Reported-by: NGregory S. Hoerner <ghoerner@transcendingthought.com>
Signed-off-by: NDave Jones <davej@redhat.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Some machines don't boot unless passed pci=nocrs.
(See https://bugzilla.redhat.com/show_bug.cgi?id=770308 for details of
  one report. Waiting on dmidecode output for others).

Currently there is a DMI whitelist, even though the default is on.

v2: drop the 1536 blacklist entry, superceded by the PNP/MMCONFIG changes from
    Bjorn
Acked-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NDave Jones <davej@redhat.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This sets all up the other bits that need to be INTEL_MID
specific rather than Moorestown specific.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Link: http://lkml.kernel.org/r/20111217174318.7207.91543.stgit@bob.linux.org.ukSigned-off-by: NIngo Molnar <mingo@elte.hu>

One printk and one comment typo fix.
Signed-off-by: NWang YanQing <udknight@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

These files were implicitly getting EXPORT_SYMBOL via device.h
which was including module.h, but that will be fixed up shortly.

By fixing these now, we can avoid seeing things like:

arch/x86/kernel/rtc.c:29: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’
arch/x86/kernel/pci-dma.c:20: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’
arch/x86/kernel/e820.c:69: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL_GPL’

[ with input from Randy Dunlap <rdunlap@xenotime.net> and also
  from Stephen Rothwell <sfr@canb.auug.org.au> ]
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

There are three different modes: PV, HVM, and initial domain 0. In all
the cases we would return -1 for failure instead of a proper error code.
Fix this by propagating the error code from the generic IRQ code.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

As with any other such change, the goal is to prevent inadvertent
writes to these structures (assuming DEBUG_RODATA is enabled), and to
separate data (possibly frequently) written to from such never getting
modified.
Reviewed-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

In summary, this DMI quirk uses the _CRS info by default for the ASUS
M2V-MX SE by turning on `pci=use_crs` and is similar to the quirk
added by commit 2491762c ("x86/PCI: use host bridge _CRS info on
ASRock ALiveSATA2-GLAN") whose commit message should be read for further
information.

Since commit 3e3da00c ("x86/pci: AMD one chain system to use pci
read out res") Linux gives the following oops:

    parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
    HDA Intel 0000:20:01.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
    HDA Intel 0000:20:01.0: setting latency timer to 64
    BUG: unable to handle kernel paging request at ffffc90011c08000
    IP: [<ffffffffa0578402>] azx_probe+0x3ad/0x86b [snd_hda_intel]
    PGD 13781a067 PUD 13781b067 PMD 1300ba067 PTE 800000fd00000173
    Oops: 0009 [#1] SMP
    last sysfs file: /sys/module/snd_pcm/initstate
    CPU 0
    Modules linked in: snd_hda_intel(+) snd_hda_codec snd_hwdep snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_midi snd_rawmidi snd_seq_midi_event tpm_tis tpm snd_seq tpm_bios psmouse parport_pc snd_timer snd_seq_device parport processor evdev snd i2c_viapro thermal_sys amd64_edac_mod k8temp i2c_core soundcore shpchp pcspkr serio_raw asus_atk0110 pci_hotplug edac_core button snd_page_alloc edac_mce_amd ext3 jbd mbcache sha256_generic cryptd aes_x86_64 aes_generic cbc dm_crypt dm_mod raid1 md_mod usbhid hid sg sd_mod crc_t10dif sr_mod cdrom ata_generic uhci_hcd sata_via pata_via libata ehci_hcd usbcore scsi_mod via_rhine mii nls_base [last unloaded: scsi_wait_scan]
    Pid: 1153, comm: work_for_cpu Not tainted 2.6.37-1-amd64 #1 M2V-MX SE/System Product Name
    RIP: 0010:[<ffffffffa0578402>]  [<ffffffffa0578402>] azx_probe+0x3ad/0x86b [snd_hda_intel]
    RSP: 0018:ffff88013153fe50  EFLAGS: 00010286
    RAX: ffffc90011c08000 RBX: ffff88013029ec00 RCX: 0000000000000006
    RDX: 0000000000000000 RSI: 0000000000000246 RDI: 0000000000000246
    RBP: ffff88013341d000 R08: 0000000000000000 R09: 0000000000000040
    R10: 0000000000000286 R11: 0000000000003731 R12: ffff88013029c400
    R13: 0000000000000000 R14: 0000000000000000 R15: ffff88013341d090
    FS:  0000000000000000(0000) GS:ffff8800bfc00000(0000) knlGS:00000000f7610ab0
    CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
    CR2: ffffc90011c08000 CR3: 0000000132f57000 CR4: 00000000000006f0
    DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
    DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
    Process work_for_cpu (pid: 1153, threadinfo ffff88013153e000, task ffff8801303c86c0)
    Stack:
     0000000000000005 ffffffff8123ad65 00000000000136c0 ffff88013029c400
     ffff8801303c8998 ffff88013341d000 ffff88013341d090 ffff8801322d9dc8
     ffff88013341d208 0000000000000000 0000000000000000 ffffffff811ad232
    Call Trace:
     [<ffffffff8123ad65>] ? __pm_runtime_set_status+0x162/0x186
     [<ffffffff811ad232>] ? local_pci_probe+0x49/0x92
     [<ffffffff8105afc5>] ? do_work_for_cpu+0x0/0x1b
     [<ffffffff8105afc5>] ? do_work_for_cpu+0x0/0x1b
     [<ffffffff8105afd0>] ? do_work_for_cpu+0xb/0x1b
     [<ffffffff8105fd3f>] ? kthread+0x7a/0x82
     [<ffffffff8100a824>] ? kernel_thread_helper+0x4/0x10
     [<ffffffff8105fcc5>] ? kthread+0x0/0x82
     [<ffffffff8100a820>] ? kernel_thread_helper+0x0/0x10
    Code: f4 01 00 00 ef 31 f6 48 89 df e8 29 dd ff ff 85 c0 0f 88 2b 03 00 00 48 89 ef e8 b4 39 c3 e0 8b 7b 40 e8 fc 9d b1 e0 48 8b 43 38 <66> 8b 10 66 89 14 24 8b 43 14 83 e8 03 83 f8 01 77 32 31 d2 be
    RIP  [<ffffffffa0578402>] azx_probe+0x3ad/0x86b [snd_hda_intel]
     RSP <ffff88013153fe50>
    CR2: ffffc90011c08000
    ---[ end trace 8d1f3ebc136437fd ]---

Trusting the ACPI _CRS information (`pci=use_crs`) fixes this problem.

    $ dmesg | grep -i crs # with the quirk
    PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug

The match has to be against the DMI board entries though since the vendor entries are not populated.

    DMI: System manufacturer System Product Name/M2V-MX SE, BIOS 0304    10/30/2007

This quirk should be removed when `pci=use_crs` is enabled for machines
from 2006 or earlier or some other solution is implemented.

Using coreboot [1] with this board the problem does not exist but this
quirk also does not affect it either. To be safe though the check is
tightened to only take effect when the BIOS from American Megatrends is
used.

        15:13 < ruik> but coreboot does not need that
        15:13 < ruik> because i have there only one root bus
        15:13 < ruik> the audio is behind a bridge

        $ sudo dmidecode
        BIOS Information
                Vendor: American Megatrends Inc.
                Version: 0304
                Release Date: 10/30/2007

[1] http://www.coreboot.org/

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=30552

Cc: stable@kernel.org (2.6.34)
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: x86@kernel.org
Signed-off-by: NPaul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Now that the hypercall interface changes are in -unstable, make the
kernel side code not ignore the segment (aka domain) number anymore
(which results in pretty odd behavior on such systems). Rather, if
only the old interfaces are available, don't call them for devices on
non-zero segments at all.
Signed-off-by: NJan Beulich <jbeulich@suse.com>
[v1: Edited git description]
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Commit b03e7495 ("PCI: Set PCI-E Max Payload Size on fabric")
introduced a potential NULL pointer dereference in calls to
pcie_bus_configure_settings due to attempts to access pci_bus self
variables when the self pointer is NULL.

To correct this, verify that the self pointer in pci_bus is non-NULL
before dereferencing it.
Reported-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NShyam Iyer <shyam_iyer@dell.com>
Signed-off-by: NJon Mason <mason@myri.com>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size.  There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device.  However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.

This can be achieved two ways:

- A conservative approach is to use the smallest common denominator of
  the entire tree below a root complex for every device on that fabric.

This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.

It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.

- A more optimal way is possible, if it falls within a couple of
  constraints:
* The top-level host bridge will never generate packets larger than the
  smallest TLP (or if it can be controlled independently from its MPS at
  least)
* The device will never generate packets larger than MPS (which can be
  configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
  some additional code to specifically deal with that case

Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.

In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.

To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls.  "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.

NOTE: due to the location of the enablement, each arch will need to add
calls to this function.  This patch only enables x86.

This patch includes a number of changes recommended by Benjamin
Herrenschmidt.

Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: NJon Mason <mason@myri.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Commit 6e8af08d enables pci=bfsort on
future Dell systems. But the identification string 'Dell System' matches
on already existing whitelist, which do not have SMBIOS type 0xB1,
causing pci=bfsort not being set on existing whitelist.

This patch fixes the regression by moving the type 0xB1 check beyond the
existing whitelist so that existing whitelist is walked before.
Signed-off-by: NShyam Iyer <shyam_iyer@dell.com>
Signed-off-by: NNarendra K <narendra_k@dell.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Aside of the usual motivation for constification,  this function has a
history of being abused a hook for interrupt and other fixups so I turned
this function const ages ago in the MIPS code but it should be done
treewide.

Due to function pointer passing in varous places a few other functions
had to be constified as well.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
To: Anton Vorontsov <avorontsov@mvista.com>
To: Chris Metcalf <cmetcalf@tilera.com>
To: Colin Cross <ccross@android.com>
Acked-by: N"David S. Miller" <davem@davemloft.net>
To: Eric Miao <eric.y.miao@gmail.com>
To: Erik Gilling <konkers@android.com>
Acked-by: NGuan Xuetao <gxt@mprc.pku.edu.cn>
To: "H. Peter Anvin" <hpa@zytor.com>
To: Imre Kaloz <kaloz@openwrt.org>
To: Ingo Molnar <mingo@redhat.com>
To: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
To: Jesse Barnes <jbarnes@virtuousgeek.org>
To: Krzysztof Halasa <khc@pm.waw.pl>
To: Lennert Buytenhek <kernel@wantstofly.org>
To: Matt Turner <mattst88@gmail.com>
To: Nicolas Pitre <nico@fluxnic.net>
To: Olof Johansson <olof@lixom.net>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
To: Richard Henderson <rth@twiddle.net>
To: Russell King <linux@arm.linux.org.uk>
To: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-alpha@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-pci@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: sparclinux@vger.kernel.org
Cc: x86@kernel.org
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Without this change, the majority of the raw PCI config space access
functions silently ignore a non-zero segment argument, which is
certainly wrong.

Apart from pci_direct_conf1, all other non-MMCFG access methods get
used only for non-extended accesses (i.e. assigned to raw_pci_ops
only). Consequently, with the way raw_pci_{read,write}() work, it would
be a coding error to call these functions with a non-zero segment (with
the current call flow this cannot happen afaict).

The access method 1 accessor, as it can be used for extended accesses
(on AMD systems) instead gets checks added for the passed in segment to
be zero. This would be the case when on such a system having multiple
PCI segments (don't know whether any exist in practice) MMCFG for some
reason is not usable, and method 1 gets selected for doing extended
accesses. Rather than accessing the wrong device's config space, the
function will now error out.

v2: Convert BUG_ON() to WARN_ON(), and extend description as per Ingo's
request.
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Reviewed-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Host bridge windows are top-level resources, so if we find a host bridge
window conflict, it's probably with a hard-coded legacy reservation.
Moving host bridge windows is theoretically possible, but we don't support
it; we just ignore windows with conflicts, and it's not worth making this
a user-visible error.
Reported-and-tested-by: NJools Wills <jools@oxfordinspire.co.uk>
References: https://bugzilla.kernel.org/show_bug.cgi?id=38522Reported-by: NDas <dasfox@gmail.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=16497Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

In the past we would only use the function's value if the
returned value was not equal to 'acpi_sci_override_gsi'. Meaning
that the INT_SRV_OVR values for global and source irq were different.
But it is OK to use the function's value even when the global
and source irq are the same.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

In the past (2.6.38) the 'xen_allocate_pirq_gsi' would allocate
an entry in a Linux IRQ -> {XEN_IRQ, type, event, ..} array. All
of that has been removed in 2.6.39 and the Xen IRQ subsystem uses
an linked list that is populated when the call to
'xen_allocate_irq_gsi' (universally done from any of the xen_bind_*
calls) is done. The 'xen_allocate_pirq_gsi' is a NOP and there is
no need for it anymore so lets remove it.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

As the code paths that are guarded by CONFIG_XEN_DOM0 already depend
on CONFIG_ACPI so the extra #ifdef is not required. The earlier
patch that added them in had done its job.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

.. which means we can preset of NR_IRQS_LEGACY interrupts using
the 'acpi_get_override_irq' API before this loop.
This means that we can get the IRQ's polarity (and trigger) from either
the ACPI (or MP); or use the default values. This fixes a bug if we did
not have an IOAPIC we would not been able to preset the IRQ's polarity
if the MP table existed.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Since they are only called once and the rest of the pci_xen_*
functions follow the same pattern of setup.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

.. to cut down on the code duplicity.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Not before .. also that code segment starts looking like the HVM one.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

In the past we would guard those code segments to be dependent
on CONFIG_XEN_DOM0 (which depends on CONFIG_ACPI) so this patch is
not stricly necessary. But the next patch will merge common
HVM and initial domain code and we want to make sure the CONFIG_ACPI
dependency is preserved - as HVM code does not depend on CONFIG_XEN_DOM0.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Update the out-dated comment at the beginning of the file.
Also provide the copyrights of folks who have been contributing
to this code lately.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

The file is hard to read. Move the code around so that
the contents of it follows a uniform format:
 - setup GSIs - PV, HVM, and initial domain case
 - then MSI/MSI-x setup - PV, HVM and then initial domain case.
 - then MSI/MSI-x teardown - same order.
 - lastly, the __init functions in PV, HVM, and initial domain order.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Previously we would check for acpi_sci_override_gsi == gsi every time
a PCI device was enabled. That works during early bootup, but later
on it could lead to triggering unnecessarily the acpi_gsi_to_irq(..) lookup.
The reason is that acpi_sci_override_gsi was declared in __initdata and
after early bootup could contain bogus values.

This patch moves the check for acpi_sci_override_gsi to the
site where the ACPI SCI is preset.

CC: stable@kernel.org
Reported-by: NRaghavendra D Prabhu <rprabhu@wnohang.net>
Tested-by: NRaghavendra D Prabhu <rprabhu@wnohang.net>
[http://lists.xensource.com/archives/html/xen-devel/2011-07/msg00154.html]
Suggested-by: NIan Campbell <ijc@hellion.org.uk>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

In the past we would use the GSI value to preset the ACPI SCI
IRQ which worked great as GSI == IRQ:

ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)

While that is most often seen, there are some oddities:

ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level)

which means that GSI 20 (or pin 20) is to be overriden for IRQ 9.
Our code that presets the interrupt for ACPI SCI however would
use the GSI 20 instead of IRQ 9 ending up with:

xen: sci override: global_irq=20 trigger=0 polarity=1
xen: registering gsi 20 triggering 0 polarity 1
xen: --> pirq=20 -> irq=20
xen: acpi sci 20
.. snip..
calling  acpi_init+0x0/0xbc @ 1
ACPI: SCI (IRQ9) allocation failed
ACPI Exception: AE_NOT_ACQUIRED, Unable to install System Control Interrupt handler (20110413/evevent-119)
ACPI: Unable to start the ACPI Interpreter

as the ACPI interpreter made a call to 'acpi_gsi_to_irq' which got nine.
It used that value to request an IRQ (request_irq) and since that was not
present it failed.

The fix is to recognize that for interrupts that are overriden (in our
case we only care about the ACPI SCI) we should use the IRQ number
to present the IRQ instead of the using GSI. End result is that we get:

xen: sci override: global_irq=20 trigger=0 polarity=1
xen: registering gsi 20 triggering 0 polarity 1
xen: --> pirq=20 -> irq=9 (gsi=9)
xen: acpi sci 9

which fixes the ACPI interpreter failing on startup.

CC: stable@kernel.org
Reported-by: NLiwei <xieliwei@gmail.com>
Tested-by: NLiwei <xieliwei@gmail.com>
[http://lists.xensource.com/archives/html/xen-devel/2011-06/msg01727.html]
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Enable 64-bit ACPI MFCG support for SGI UV2 platform. The check
is similar to the check on UV1. UV2 has a different oem_id
string.
Signed-off-by: NJack Steiner <steiner@sgi.com>
Link: http://lkml.kernel.org/r/20110602195943.GA27079@sgi.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

The flags field of struct resource from linux/ioport.h is "unsigned
long". Change the "type" parameter of coalesce_windows() function to
match that field. This fixes the following warning messages when
compiling with "make C=1 W=1 bzImage modules":

arch/x86/pci/acpi.c: In function ‘coalesce_windows’:
arch/x86/pci/acpi.c:198: warning: conversion to ‘long unsigned int’ from ‘int’ may change the sign of the result
arch/x86/pci/acpi.c:203: warning: conversion to ‘long unsigned int’ from ‘int’ may change the sign of the result
Signed-off-by: NMárton Németh <nm127@freemail.hu>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

On various newer Intel systems the PCI bus(ses) the non-core devices
live on aren't getting announced by ACPI except through the bus range
covered by mmconfig. At least the i7core-edac driver depends on these
devices getting detected.

Mauro, could you check whether with this change the Xeon 55xx hack in
that driver can go away altogether, and with it the bogus exporting of
pcibios_scan_specific_bus()?
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Aristeu Sergio <arozansk@redhat.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

If we have CONFIG_XEN and the other parameters to build an
Linux kernel that is non-privileged, the xen_[find|register|unregister]_
device_domain_owner functions should not be compiled. They should
use the nops defined in arch/x86/include/asm/xen/pci.h instead.

This fixes:

arch/x86/pci/xen.c:496: error: redefinition of ‘xen_find_device_domain_owner’
arch/x86/include/asm/xen/pci.h:25: note: previous definition of ‘xen_find_device_domain_owner’ was here
arch/x86/pci/xen.c:510: error: redefinition of ‘xen_register_device_domain_owner’
arch/x86/include/asm/xen/pci.h:29: note: previous definition of ‘xen_register_device_domain_owner’ was here
arch/x86/pci/xen.c:532: error: redefinition of ‘xen_unregister_device_domain_owner’
arch/x86/include/asm/xen/pci.h:34: note: previous definition of ‘xen_unregister_device_domain_owner’ was here
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reported-by: NRandy Dunlap <randy.dunlap@oracle.com>