We use 1:1 mapping between QPs and SRQs on receive side,
so additional indirection level not required. Allocated the receive
buffers for the RSS QPs.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no point in using more QPs then actual number of receive rings.
If the RSS function for two streams gives the same result modulo number
of rings, they will arrive to the same RX ring anyway.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the net device is identified as "sender" (number of sent packets
is higher then the number of received packets and the incoming packets are
small), set the moderation time to its low limit.
We do it because the incoming packets are acks, and we don't want to delay them
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hibernation is unsupported for now, which meets the actual
implementation in the driver. For free/thaw, the chip's D2 state should
be entered.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Acked-by: <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The datasheet say "When not enabling packing, the MinFrag value must
remain at 0".  Do not set value to RxFragSize register if
TC35815_USE_PACKEDBUFFER disabled.

This is not a bugfix.  No real problem reported on this.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Miss_Cnt register is cleared by reading.  Accumulate its value to
rx_missed_errors count.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current timeout value is too short for very high-load condition
which jiffies might jump up in busy-loop.
Also add minimum delay before checking completion of MDIO.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clear Int_BLEx / Int_FDAEx after (not before) processing Rx interrupt.
This will reduce number of unnecessary interrupts.
Also print rx error messages only if netif_msg_rx_err() enabled.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It seems Rx_StripCRC cause trouble on recovering from the BLEx (Buffer
List Exhaust) or FDAEx (Free Descriptor Area Exhaust) condition.
Do not use it.

Also bump version number up.
Reported-by: NRalf Roesch <ralf.roesch@rw-gmbh.de>
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 88045b3c
	cxgb3: fix mac index mapping

	Override the mac index computation for the gen2 adapter,
	as each port is expected to use index 0.

introduces a regression on 2 port 1G adapter
as its xauicfg vpd value is null.
Add a check on the device id.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update the driver version number for any bug reports from end users.
Signed-off-by: NBenjamin LaHaise <ben.lahaise@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements prefetching of skb->data from a copy of the pointer
in the descriptor (which is already in the L1 cache at this point).  This
improves netperf rx performance (netperf -L 0,0 -c -H 192.168.254.2 -- -M
131072 -m 131072) by 4.9% on a P4 Xeon host.
Signed-off-by: NBenjamin LaHaise <ben.lahaise@neterion.com>
Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prefetches RxD descriptors which helps to lower the latency of a
cache miss in vxge_hw_ring_rxd_next_completed.  This lowers the % of CPU
time used by vxge_hw_ring_rxd_next_completed() where the descriptor is
accessed in profiling netperf on a P4 Xeon from 1.5% to 1.0%.
Signed-off-by: NBenjamin LaHaise <ben.lahaise@neterion.com>
Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

wmb() is extremely heavy on x86.  The semantics required in the driver are
provided by mmiowb(), so use that and improve tx performance on P4 Xeons by
5-10%.
Signed-off-by: NBenjamin LaHaise <ben.lahaise@neterion.com>
Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a case in the transmit completion code which was resulting
in pktgen hanging at the end of a run.  The cause is due to the fact that
the ->cb[] area of an skb cannot be used in a network driver's transmit
path, as that area belongs to the network protocol.  Pktgen hangs, as it
sends out the same packet multiple times, and vxge's use of this area of
the skb for a temporary list can only add the packet to the temporary list
once (while it may be on the queue many times).  The fix is to remove this
abuse of skb->cb[].  Instead, skb pointers are placed into a temporary
stack array, and then free outside of the tx lock.  This retains the smp
optimization of doing dev_kfree_skb() outside of the tx lock.
Signed-off-by: NBenjamin LaHaise <ben.lahaise@neterion.com>
Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The vxge driver will drop a packet in its transmit function if the number
of TxDs available hits 0.  Instead of doing that, simply stop the transmit
queue when transmitting a packet with the last available TxD.
Signed-off-by: NBenjamin LaHaise <ben.lahaise@neterion.com>
Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The skb priority to vlan-qos egress mapping that can be configured using
set_egress_map with vconfig is overriden by the DCB code in the driver.

This patch allows this existing mechanism to work and will increase the
configuration flexibility of DCB mode on Linux.

A hierarchy of configuration is:

1. Modifies the ixgbe_select_queue() routine for DCB mode to return the
priority value from the VLAN tag. It will normally be zero, unless the egress
priority map has modified it. This will get packets into the correct queue and
result in the queue_mapping field being set correctly.

2. Any tc filter which modifies queue_mapping will be honored, as the filters
are handled after the vlan egress map is handled.
Signed-off-by: NLucy Liu <lucy.liu@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is a bug fix to avoid system going into a bad state when
driver is loaded in context of kdump kernel. The patch fixes the issue
by performing a soft reset of pci function at probe time.
Signed-off-by: Nsarveshwarb <sarveshwarb@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to handle aggregate packets from firmware.
Local TCP flows are automatically identified by firmware
based on the dest IP hash added by driver for local IP
addresses.

The packets are sent down on the jumbo rx ring.
Signed-off-by: NNarender Kumar <narender.kumar@qlogic.com>
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove unnecessary offsetof calulations on these structures:
netxen_board_info, netxen_user_old_info, netxen_new_user_info.

The offsets into the flash are fixed, don't need to be calculated.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the calculation of remaining header length in TSO
over vlan device case. This was inadvertently missed
out in patch 028afe71 ("netxen: add vlan
tx acceleration support").
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Starting with version 0.5.1, cpmac is no longer broken.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch slows down the MDIO_ALIVE busy waiting to let
switches and PHY come up after reset. Previous loop was
too quick for IC+175C and ADM6996C/L switches to come up.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for fixed PHY connected in MII mode
to cpmac. We allow external and dumb_switch module parameters
to override the PHY detection process since they are always connected
with MDIO bus identifier 0. This lets fixed PHYs to be detected
correctly and be connected to the their corresponding MDIO
bus identifier.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the wrong MDIO bus identifier which was
set to 0 unconditionaly, suitable for external switches while
it is actually 1 for PHYs different than external switches
which are autodetected.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CC [M]  drivers/net/wireless/ath/ath9k/eeprom.o
drivers/net/wireless/ath/ath9k/eeprom.c: In function ‘ath9k_hw_AR9287_check_eeprom’:
drivers/net/wireless/ath/ath9k/eeprom.c:2866: warning: comparison of distinct pointer types lacks a cast

Cc: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We forgot to cancel this work at the stop() callback.

------------[ cut here ]------------
WARNING: at net/mac80211/util.c:511 ieee80211_queue_delayed_work+0x3a/0x40 [mac80211]()
Hardware name: 6460DWU
queueing ieee80211 work while going to suspend
Modules linked in: <-- snip -->
Pid: 5124, comm: phy0 Tainted: G        W  2.6.31-rc3-wl #4
Call Trace:
 [<ffffffffa03adcda>] ? ieee80211_queue_delayed_work+0x3a/0x40 [mac80211]
 [<ffffffff810552b8>] warn_slowpath_common+0x78/0xd0
 [<ffffffff81055394>] warn_slowpath_fmt+0x64/0x70
 [<ffffffff814ed2c9>] ? thread_return+0x3e/0x635
 [<ffffffffa03adcda>] ieee80211_queue_delayed_work+0x3a/0x40 [mac80211]
 [<ffffffffa0297690>] ath_tx_complete_poll_work+0xc0/0x100 [ath9k]
 [<ffffffffa02975d0>] ? ath_tx_complete_poll_work+0x0/0x100 [ath9k]
 [<ffffffff81069b68>] worker_thread+0x178/0x260
 [<ffffffff8106ecc0>] ? autoremove_wake_function+0x0/0x40
 [<ffffffff810699f0>] ? worker_thread+0x0/0x260
 [<ffffffff8106e89e>] kthread+0x9e/0xb0
 [<ffffffff8101302a>] child_rip+0xa/0x20
 [<ffffffff8106e800>] ? kthread+0x0/0xb0
 [<ffffffff81013020>] ? child_rip+0x0/0x20
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We will finalize this after some driver core changes, for now
we leave this unsupported.

Cc: Stephen Chen <stephen.chen@atheros.com>
Cc: Zhifeng Cai <zhifeng.cai@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cc: Stephen Chen <stephen.chen@atheros.com>
Cc: Zhifeng Cai <zhifeng.cai@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These will be used later to add support for ar9271.

Cc: Stephen Chen <stephen.chen@atheros.com>
Cc: Zhifeng Cai <zhifeng.cai@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We don't use typdefs on ath9k, remove that _t.

Cc: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k_hw_keyreset() has a spurious check for ah->curchan..
remove it.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The keycache reset will not fail as right above we ensure
to set the sc->keymax to be <= ah->caps.keycache_size. Just remove
this dangling check.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If hw initialization fails (ath9k_hw_init()) on ath_init_softc()
we bail out and call ath9k_hw_detach(). The call ath9k_hw_detach()
is conditional though as ath9k_hw_init() could itself have called
ath9k_hw_detach(). Just describing this is itself a brain twister.
Avoid this nonsense by removing ath9k_hw_detach() from ath9k_hw_init().

Upon hw initialization failure we expect the callers to take care of
the cleanup.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This makes it clear what this does.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>