This is a (final?) hack to support the odd DMA allocation requirements
of the b44 hardware.  The b44 hardware has a 30-bit DMA mask.  On x86,
anything less than a 32-bit DMA mask forces allocations into the 16MB
GFP_DMA range.  The memory there is somewhat limited, often resulting
in an inability to initialize the b44 driver.

This hack uses streaming DMA allocation APIs in order to provide an
alternative in case the GFP_DMA allocation fails.  It is somewhat ugly,
but not much worse than the similar existing hacks to support SKB
allocations in the same driver.  FWIW, I have received positive
feedback on this from several Fedora users.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Expand comment explaining MAC address selection for replicated IGMP
frames transmitted in bonding mode 1 (active-backup).  Also, a small
whitespace cleanup.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Add "HasHltClk" flag for RTL-8100B/8139D hardware in order to fix
problems resuming from suspend-to-RAM.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Fix some simple typos in the bonding.txt file.  The typos are in areas
relating to loading the bonding driver multiple times.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

work_done is overwritten each time through the rx_action loop in
epic_poll.  This screws-up the NAPI accounting if the loop is executed
more than once.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Get rid of the mdelay call in rhine_disable_linkmon.  The function
is called from the via-rhine versions of mdio_read and mdio_write.
Those functions are indirectly called from rhine_check_media and
rhine_tx_timeout, both of which can be called in interrupt context.

So, create tx_timeout_task and check_media_task as instances of struct
work_struct inside of rhine_private.  Then, change rhine_tx_timeout to
invoke schedule_work for tx_timeout_task (i.e. rhine_tx_timeout_task),
moving the work to process context.  Also, change rhine_error (invoked
from rhine_interrupt) to invoke schedule_work for check_media_task
(i.e. rhine_check_media_task), which simply calls rhine_check media
in process context.  Finally, add a call to flush_scheduled_work in
rhine_close to avoid any resource conflicts with pending work items.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

drivers/net/e1000/e1000_main.c: In function `e1000_intr':
drivers/net/e1000/e1000_main.c:3156: error: `i' undeclared (first use in this function)
drivers/net/e1000/e1000_main.c:3156: error: (Each undeclared identifier is reported only once
drivers/net/e1000/e1000_main.c:3156: error: for each function it appears in.)

This function is foul.

Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 drivers/net/Kconfig   |    8 +
 drivers/net/Makefile  |    1
 drivers/net/mipsnet.c |  371 ++++++++++++++++++++++++++++++++++++++++++++++++++
 drivers/net/mipsnet.h |  127 +++++++++++++++++
 4 files changed, 507 insertions(+)
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Support for Toshiba's RBHMA4500 eval board for the TX4938.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 drivers/net/ne.c |   15 +++++++++++++++
 1 files changed, 15 insertions(+)
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Use physical addresses at the interface level, letting drivers remap
them as appropriate.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 drivers/net/declance.c |   26 ++++++++++----------------
 1 files changed, 10 insertions(+), 16 deletions(-)
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 drivers/net/declance.c |    2 +-
 1 files changed, 1 insertion(+), 1 deletion(-)
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

These should really be addresses obtained with ioremap() or some
bus-specific backend, but for now...
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 drivers/net/declance.c |    4 ++--
 1 files changed, 2 insertions(+), 2 deletions(-)
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 drivers/net/declance.c |    5 +++--
 1 files changed, 3 insertions(+), 2 deletions(-)
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 drivers/net/sgiseeq.c       |   28 ++++++++++++++--------------
 include/asm-mips/sgi/hpc3.h |   40 ++++++++++++++++++++--------------------
 2 files changed, 34 insertions(+), 34 deletions(-)
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 drivers/net/sgiseeq.c |    9 ++++-----
 1 files changed, 4 insertions(+), 5 deletions(-)
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 drivers/net/tulip/de2104x.c |    5 +++++
 1 files changed, 5 insertions(+)
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

 o Add support for DP83847 MII.
 o remove unused variable.
 o Add some initialisations so even an unknown MII won't result in a crash.
 o Correct error message to "no known MIIs found".
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 drivers/net/au1000_eth.c |   13 +++++--------
 1 files changed, 5 insertions(+), 8 deletions(-)
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 drivers/net/sb1250-mac.c |    9 ++++++++-
 1 files changed, 8 insertions(+), 1 deletion(-)
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 drivers/net/sb1250-mac.c |    2 +-
 1 files changed, 1 insertion(+), 1 deletion(-)
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

This fixes division by zero bug in ieee80211_wx_get_scan().
Signed-off-by: NJiri Benc <jbenc@suse.cz>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

If .owner isn't set the module can be unloaded even while still active.
Signed-off-by: NRalf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

SMACK (Stuttgart Modified Amateurradio CRC KISS) is a KISS variant that
uses CRC16 checksums to secure data transfers between the modem and host.
It's also used to communicate over a pty to applications such as Wampes.

Patches for Linux 2.4 by Thomas Osterried DL9SAU, upgraded to the latest
mkiss 2.6 mkiss driver by me.
Signed-off-by: NThomas Osterried DL9SAU <thomas@x-berg.in-berlin.de>
Signed-off-by: NRalf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

From Suzanne Wood <suzannew@cs.pdx.edu>:

Clarify RCU implementation in bpqether.c.

Because bpq_new_device() calls list_add_rcu() and bpq_free_device() calls
list_del_rcu(), substitute list_for_each_entry_rcu() for
list_for_each_entry() in bpq_get_ax25_dev() and in bpq_seq_start().

Add rcu dereference protection in bpq_seq_next().

The rcu_read_lock()/unlock() in bpq_device_event() are removed because
netdev event handlers are called with RTNL locking in place.

FYI: bpq_free_device() calls list_del_rcu() which, per list.h, requires
synchronize_rcu() which can block or call_rcu() or call_rcu_bh() which
cannot block.  Herbert Xu notes that synchronization is done here by
unregister_netdevice().  This calls synchronize_net() which in turn uses
synchronize_rcu().
Signed-off-by: NRalf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

This patch fixes the following bugs with offline diagnostics
code(run with "ethtool -t").

1. After running offline diagnostics, adapter would report
corrupted packets on receive. This was because of adapter not
being brought out of "RLDRAM test mode".
2. Current EEPROM test works only for Xframe I. Since Xframe II
uses different interface(SPI), support for this interface has
been added. Also, since SPI supports write access to all areas
of EEPROM, negative testing is done only for Xframe I.
3. Return values from subfunctions of offline diagnostics have
been corrected.
4. In register test, expected value from rx_queue_cfg register
is made to depend on adapter type.
5. After the test, need to restore values at EEPROM offsets
0x4F0 and 0x7F0. These locations were modified as part of test.
6. Use macro SPECIAL_REG_WRITE for write access to mc_rldram_test_ctrl
register. Also, couple of unnecessary writes to mc_rldram_test_ctrl
have been removed.
Signed-off-by: NRavinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The following build error happens with 2.6.14-rc4 when CONFIG_KALLSYMS is
not defined.  The error message in a fragment of the output was:

  CC      arch/i386/lib/usercopy.o
  AR      arch/i386/lib/lib.a
/bin/sh: line 1: +@: command not found
make[3]: warning: jobserver unavailable: using -j1.  Add `+' to parent make rule.
  CHK     include/linux/compile.h
Signed-off-by: NMark Rustad <mrustad@mac.com>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

lock_kiocb() was introduced to serialize retrying and cancellation.  In the
process of doing so it tried to sleep waiting for KIF_LOCKED while holding
the ctx_lock spinlock.  Recent fixes have ensured that multiple concurrent
retries won't be attempted for a given iocb.  Cancel has other problems and
has no significant in-tree users that have been complaining about it.  So
for the immediate future we'll revert sleeping with the lock held and will
address proper cancellation and retry serialization in the future.
Signed-off-by: NZach Brown <zach.brown@oracle.com>
Acked-by: NBenjamin LaHaise <bcrl@kvack.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Only signal completion after marking request slot as free, otherwise other
processor can free request structure before we finish using it.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix -EIO on /proc/acpi/events after suspends.  This actually breaks
suspending by power button in many setups.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Since Revision 1.10 was released the n_r3964 module wasn't able to receive any
data.  The reason for that behavior is because there were some wrong calls of
mod_timer(...) in the function receive_char (...).  This patch should fix this
problem and was successfully tested with talking to some kuka industrial
robots.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Currently you do not get all the map entries on nommu systems because the
start function doesn't index into the list using the value of "pos".
Signed-off-by: NDavid McCullough <davidm@snapgear.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This makes call_rcu() keep track of how many events there are on the RCU
list, and cause a reschedule event when the list gets too long.

This helps keep RCU event lists down.
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This change makes quirk_intel_ide_combined() dependent on the precise
conditions under which it is needed:

* IDE is built in
* IDE SATA option is not set
* ata_piix or ahci drivers are enabled

This fixes an issue where some modular configurations would not cause
the quirk to be enabled.
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
Signed-off-by: NLinus torvalds <torvalds@osdl.org>

Make sure we release the task struct properly when releasing pending
timers.

release_task() does write_lock_irq(&tasklist_lock), so it can't race
with run_posix_cpu_timers() on any cpu.
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Oopsable since nfs_wait_on_inode() can get called as part of iput_final().

Unnecessary since the caller had better be damned sure that the inode won't
disappear from underneath it anyway.
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If the data cache has been marked as potentially invalid by nfs_refresh_inode,
we should invalidate it rather than assume that changes are due to our own
activity.

Also ensure that we always start with a valid cache before declaring it
to be protected by a delegation.
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

During the development of an USB device I found a bug in the handling of
Highspeed HID devices in the kernel.

What happened?

Highspeed HID devices are correctly recognized and enumerated by the
kernel. But even if usbhid kernel module is loaded, no HID reports are
received by the kernel.

The output of the hardware USB analyzer told me that the host doesn't
even poll for interrupt IN transfers (even the "interrupt in" USB
transfer are polled by the host).

After some debugging in hid-core.c I've found the reason.

In case of a highspeed device, the endpoint interval is re-calculated in
driver/usb/input/hid-core.c:

line 1669:
             /* handle potential highspeed HID correctly */
             interval = endpoint->bInterval;
             if (dev->speed == USB_SPEED_HIGH)
                   interval = 1 << (interval - 1);

Basically this calculation is correct (refer to USB 2.0 spec, 9.6.6).
This new calculated value of "interval" is used as input for
usb_fill_int_urb:

line 1685:

            usb_fill_int_urb(hid->urbin, dev, pipe, hid->inbuf, 0,
                   hid_irq_in, hid, interval);

Unfortunately the same calculation as above is done a second time in
usb_fill_int_urb in the file include/linux/usb.h:

line 933:
        if (dev->speed == USB_SPEED_HIGH)
                urb->interval = 1 << (interval - 1);
        else
                urb->interval = interval;

This means, that if the endpoint descriptor (of a high speed device)
specifies e.g. bInterval = 7, the urb->interval gets the value:

hid-core.c: interval = 1 << (7-1) = 0x40 = 64
urb->interval = 1 << (interval -1) = 1 << (63) = integer overflow

Because of this the value of urb->interval is sometimes negative and is
rejected in core/urb.c:
line 353:
                /* too small? */
                if (urb->interval <= 0)
                        return -EINVAL;

The conclusion is, that the recalculaton of the interval (which is
necessary for highspeed) should not be made twice, because this is
simply wrong. ;-)

Re-calculation in usb_fill_int_urb makes more sense, because it is the
most general approach. So it would make sense to remove it from
hid-core.c.

Because in hid-core.c the interval variable is only used for calling
usb_fill_int_urb, it is no problem to remove the highspeed
re-calculation in this file.
Signed-off-by: NChristian Krause <chkr@plauener.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Increased use of scatter-gather by usb-storage driver after 2.6.13 has
exposed a buggy codepath in isp116x-hcd, which was probably never
visited before: bug happened only for those urbs, for which
URB_SHORT_NOT_OK was set AND short transfer occurred.

The fix attached was tested in 2 ways: (a) it fixed failing
initialization of a flash drive with an embedded hub; (b) the fix was
tested with 'usbtest' against a modified g_zero driver (on top of
net2280), which generated short bulk IN transfers of various lengths
including multiples and non-multiples of max_packet_length.
Signed-off-by: NOlav Kongas <ok@artecdesign.ee>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Dipankar made RCU limit the batch size to improve latency, but that
approach is unworkable: it can cause the RCU queues to grow without
bounds, since the batch limiter ended up limiting the callbacks.

So make the limit much higher, and start planning on instead limiting
the batch size by doing RCU callbacks more often if the queue looks like
it might be growing too long.
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>