- 28 5月, 2010 1 次提交
-
-
由 Felipe Balbi 提交于
A few architectures, like OMAP, allow you to set a debouncing time for the gpio before generating the IRQ. Teach gpiolib about that. Mark said: : This would be generally useful for embedded systems, especially where : the interrupt concerned is a wake source. It allows drivers to avoid : spurious interrupts from noisy sources so if the hardware supports it : the driver can avoid having to explicitly wait for the signal to become : stable and software has to cope with fewer events. We've lived without : it for quite some time, though. David said: : I looked at adding debounce support to the generic GPIO calls (and thus : gpiolib) some time back, but decided against it. I forget why at this : time (check list archives) but it wasn't because of lack of utility in : certain contexts. : : One thing to watch out for is just how variable the hardware capabilities : are. Atmel GPIOs have something like a fixed number of 32K clock cycles : for debounce, twl4030 had something odd, OMAPs were more like the Atmel : chips but with a different clock. In some cases debouncing had to be : ganged, not per-GPIO. And so forth. Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Cc: Tony Lindgren <tony@atomide.com> Cc: David Brownell <david-b@pacbell.net> Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 16 12月, 2009 1 次提交
-
-
由 Jani Nikula 提交于
Drivers may use gpiolib sysfs as part of their public user space interface. The GPIO number and polarity might change from board to board. The gpio_export_link() call can be used to hide the GPIO number from user space. Add support for also hiding the GPIO line polarity changes from user space. Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 23 9月, 2009 1 次提交
-
-
由 Jani Nikula 提交于
Commit 926b663c (gpiolib: allow GPIOs to be named) already provides naming on the chip level. This patch provides more flexibility by allowing multiple names where ever in sysfs on a per GPIO basis. Adapted from David Brownell's comments on a similar concept: http://lkml.org/lkml/2009/4/20/203. [randy.dunlap@oracle.com: fix build for CONFIG_GENERIC_GPIO=n] Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com> Acked-by: NDavid Brownell <david-b@pacbell.net> Cc: Daniel Silverstone <dsilvers@simtec.co.uk> Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 17 10月, 2008 1 次提交
-
-
由 Uwe Kleine-König 提交于
According to the documentation gpio_free should only be called from task context only. To make this more explicit add a might sleep to all implementations. This is the generic part which changes gpiolib and the fallback implementation only. Signed-off-by: NUwe Kleine-König <ukleinek@informatik.uni-freiburg.de> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 26 7月, 2008 1 次提交
-
-
由 David Brownell 提交于
This adds a simple sysfs interface for GPIOs. /sys/class/gpio /export ... asks the kernel to export a GPIO to userspace /unexport ... to return a GPIO to the kernel /gpioN ... for each exported GPIO #N /value ... always readable, writes fail for input GPIOs /direction ... r/w as: in, out (default low); write high, low /gpiochipN ... for each gpiochip; #N is its first GPIO /base ... (r/o) same as N /label ... (r/o) descriptive, not necessarily unique /ngpio ... (r/o) number of GPIOs; numbered N .. N+(ngpio - 1) GPIOs claimed by kernel code may be exported by its owner using a new gpio_export() call, which should be most useful for driver debugging. Such exports may optionally be done without a "direction" attribute. Userspace may ask to take over a GPIO by writing to a sysfs control file, helping to cope with incomplete board support or other "one-off" requirements that don't merit full kernel support: echo 23 > /sys/class/gpio/export ... will gpio_request(23, "sysfs") and gpio_export(23); use /sys/class/gpio/gpio-23/direction to (re)configure it, when that GPIO can be used as both input and output. echo 23 > /sys/class/gpio/unexport ... will gpio_free(23), when it was exported as above The extra D-space footprint is a few hundred bytes, except for the sysfs resources associated with each exported GPIO. The additional I-space footprint is about two thirds of the current size of gpiolib (!). Since no /dev node creation is involved, no "udev" support is needed. Related changes: * This adds a device pointer to "struct gpio_chip". When GPIO providers initialize that, sysfs gpio class devices become children of that device instead of being "virtual" devices. * The (few) gpio_chip providers which have such a device node have been updated. * Some gpio_chip drivers also needed to update their module "owner" field ... for which missing kerneldoc was added. * Some gpio_chips don't support input GPIOs. Those GPIOs are now flagged appropriately when the chip is registered. Based on previous patches, and discussion both on and off LKML. A Documentation/ABI/testing/sysfs-gpio update is ready to submit once this merges to mainline. [akpm@linux-foundation.org: a few maintenance build fixes] Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Cc: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de> Cc: Greg KH <greg@kroah.com> Cc: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 25 5月, 2008 1 次提交
-
-
由 David Brownell 提交于
This fixes various gpio-related build errors (mostly potential) reported in part by Russell King and Uwe Kleine-König. Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Cc: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 05 3月, 2008 1 次提交
-
-
由 David Brownell 提交于
Add a <linux/gpio.h> defining fail/warn stubs for GPIO calls on platforms that don't support the GPIO programming interface. That includes the arch-specific implementation glue otherwise. This facilitates a new model for GPIO usage: drivers that can use GPIOs if they're available, but don't require them. One example of such a driver is NAND driver for various FreeScale chips. On platforms update with GPIO support, they can be used instead of a worst-case delay to verify that the BUSY signal is off. (Also includes a couple minor unrelated doc updates.) Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-