All QCA chips have the ability to parse the CF Parameter Set
IE in beacons. If the IE is malformed in the beacons from some
APs [1], the HW locks up. In AP mode, a beacon stuck would happen
and in client mode, a disconnection usually is the result.

To fix this issue, set the AR_PCU_MISC_MODE2_CFP_IGNORE to ignore
the CFP IE in beacons - this is applicable for all chips. For
AP mode, if this issue happens, the NAV is also corrupted and has
to be reset - this will be done in a subsequent patch.

[1] : http://msujith.org/ath9k/cfp/Malformed-CF-Param.pngSigned-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

TX IQ calibration is disabled by default for AR9462, this
is done using the initvals (reg 0xa644).

But, to compensate for this, the AR_PHY_RX_DELAY register
should be set to the max allowed value when performing
calibration.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function returns a pointer. Hence return NULL instead of false.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NAlbert Pool <albertpool@solcon.nl>
Reported-by: NMichael Landrum <landrummd@gmail.com>
Acked-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Whenever the return value of snprintf() is used to calculate
remaining buffer-space, we wanted to use sncprintf() instead.

Indentation is adapted where possible. Some lines exceed the
line width limit, either they did it already before, or
since they can not be broken reasonably well.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Remove duplicate array mappings.
* Fix ETSI CCA compliance.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is missing for AR9565.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Adjust the CCA values based on the regulatory domain
present in the EEPROM.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are 2 types of WB335 cards, 1-antenna and 2-antenna.
Identify them based on PCI subsystem IDs, this will be used
for MCI/BTCOEX tweaks.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These cards are based on WB335/AR9565.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Program the HW registers (AR_PHY_CCK_DETECT, AR_PHY_MC_GAIN_CTRL)
with the correct values for AR9565 to allow LNA combining.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use a default antenna diversity value for AR9565 instead
of relying on the EEPROM/OTP programmed value.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Pull networking fixes from David Miller:

 1) If the local_df boolean is set on an SKB we have to allocate a
    unique ID even if IP_DF is set in the ipv4 headers, from Ansis
    Atteka.

 2) Some fixups for the new chipset support that went into the sfc
    driver, from Ben Hutchings.

 3) Because SCTP bypasses a good chunk of, and actually duplicates, the
    logic of the ipv6 output path, some IPSEC things don't get done
    properly.  Integrate SCTP better into the ipv6 output path so that
    these problems are fixed and such issues don't get missed in the
    future either.  From Daniel Borkmann.

 4) Fix skge regressions added by the DMA mapping error return checking
    added in v3.10, from Mikulas Patocka.

 5) Kill some more IRQF_DISABLED references, from Michael Opdenacker.

 6) Fix races and deadlocks in the bridging code, from Hong Zhiguo.

 7) Fix error handling in tun_set_iff(), in particular don't leak
    resources.  From Jason Wang.

 8) Prevent format-string injection into xen-netback driver, from Kees
    Cook.

 9) Fix regression added to netpoll ARP packet handling, in particular
    check for the right ETH_P_ARP protocol code.  From Sonic Zhang.

10) Try to deal with AMD IOMMU errors when using r8169 chips, from
    Francois Romieu.

11) Cure freezes due to recent changes in the rt2x00 wireless driver,
    from Stanislaw Gruszka.

12) Don't do SPI transfers (which can sleep) in interrupt context in
    cw1200 driver, from Solomon Peachy.

13) Fix LEDs handling bug in 5720 tg3 chips already handled for 5719.
    From Nithin Sujir.

14) Make xen_netbk_count_skb_slots() count the actual number of slots
    that will be used, taking into consideration packing and other
    issues that the transmit path will run into.  From David Vrabel.

15) Use the correct maximum age when calculating the bridge
    message_age_timer, from Chris Healy.

16) Get rid of memory leaks in mcs7780 IRDA driver, from Alexey
    Khoroshilov.

17) Netfilter conntrack extensions were converted to RCU but are not
    always freed properly using kfree_rcu().  Fix from Michal Kubecek.

18) VF reset recovery not being done correctly in qlcnic driver, from
    Manish Chopra.

19) Fix inverted test in ATM nicstar driver, from Andy Shevchenko.

20) Missing workqueue destroy in cxgb4 error handling, from Wei Yang.

21) Internal switch not initialized properly in bgmac driver, from Rafał
    Miłecki.

22) Netlink messages report wrong local and remote addresses in IPv6
    tunneling, from Ding Zhi.

23) ICMP redirects should not generate socket errors in DCCP and SCTP.
    We're still working out how this should be handled for RAW and UDP
    sockets.  From Daniel Borkmann and Duan Jiong.

24) We've had several bugs wherein the network namespace's loopback
    device gets accessed after it is free'd, NULL it out so that we can
    catch these problems more readily.  From Eric W Biederman.

25) Fix regression in TCP RTO calculations, from Neal Cardwell.

26) Fix too early free of xen-netback network device when VIFs still
    exist.  From Paul Durrant.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
  netconsole: fix a deadlock with rtnl and netconsole's mutex
  netpoll: fix NULL pointer dereference in netpoll_cleanup
  skge: fix broken driver
  ip: generate unique IP identificator if local fragmentation is allowed
  ip: use ip_hdr() in __ip_make_skb() to retrieve IP header
  xen-netback: Don't destroy the netdev until the vif is shut down
  net:dccp: do not report ICMP redirects to user space
  cnic: Fix crash in cnic_bnx2x_service_kcq()
  bnx2x, cnic, bnx2i, bnx2fc: Fix bnx2i and bnx2fc regressions.
  vxlan: Avoid creating fdb entry with NULL destination
  tcp: fix RTO calculated from cached RTT
  drivers: net: phy: cicada.c: clears warning Use #include <linux/io.h> instead of <asm/io.h>
  net loopback: Set loopback_dev to NULL when freed
  batman-adv: set the TAG flag for the vid passed to BLA
  netfilter: nfnetlink_queue: use network skb for sequence adjustment
  net: sctp: rfc4443: do not report ICMP redirects to user space
  net: usb: cdc_ether: use usb.h macros whenever possible
  net: usb: cdc_ether: fix checkpatch errors and warnings
  net: usb: cdc_ether: Use wwan interface for Telit modules
  ip6_tunnels: raddr and laddr are inverted in nl msg
  ...