This provides an option to override the value set by VBT
for selecting edp Vswing Pre-emph setting table.

v2: Adding comment about this being a temporary workaround and
making the parameter read-only (Jani)
v3: Changing mode to 0400 instead of 0 (Jani)

https://bugs.freedesktop.org/show_bug.cgi?id=89554Signed-off-by: NSonika Jindal <sonika.jindal@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Note that we also need this for skl.
Signed-off-by: NNick Hoath <nicholas.hoath@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
[danvet: Note that we also need this for skl, requested by Imre.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Use POSTING_READ() in intel_sdvo_write_sdvox() as appropriate.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Enabling BLC on BXT.
Includes register definition, and new functions for BXT.

In BXT, there are 2 sets of registers for BLC. Until there is clarity
about which set would be effective, set 1 is being used.
This would have to be re-visited if there is any change or when 2 LFPs are
enabled on BXT.

This patch enables brightness change which would be effected by use of
hot-keys or sysfs entry.

TODO:- BLC implementation will have to re-visited when
1. there is clarity about which set of registers has to be used and when.
2. CDCLK frequency is changed

v2: Jani's review comments
	- Modified comment in i915_reg.h
	- Renamed register defintions
	- Removed definition of duty cycle max. Not required now and its not 64-bit.

v3:
  - Rebase on top of VLV/CHV backlight changes, in particuliar
    bxt_set_backlight() now has a different prototype (Damien)
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NVandana Kannan <vandana.kannan@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Shankar, Uma <uma.shankar@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

wa_batchbuffer is part of some error states. Make sure it
is freed.
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We should no longer enter the codec enable/disable functions in question
with port A anyway, but to err on the safe side, keep the warnings. Just
bail out early without messing with the registers.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The specs tell us to ungate PG1 and Misc I/O at display init. We'll use
the PLLS power domain to ensure those two power wells are up.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Let's keep that list sorted!
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The patch 69876bed: "drm/i915/gen8:
page directories rework allocation" added an overflow warning, but the
mask had an extra 0. Use less typo-prone option suggested by Dave
instead, to check for (start + length) >= 0x100000000ULL.

This check will be unnecessary after gen8_alloc_va_range handles more
than 4 PDPs (48b addressing).

v2: Really check for 32b overflow (Ville)
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMichel Thierry <michel.thierry@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Unbinding doesn't always lead to unconditional destruction
of vma. This destruction avoidance happens if vma is part of
execbuffer relocation list or if vma is being considered for
eviction in i915_gem_evict_something().

For those other users, mark the vma unbound so that
the correct state of this vma is preserved.
Reported-by: NChris Wilson <chris@chris-wilson.co.ok>
Cc: Chris Wilson <chris@chris-wilson.co.ok>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Because they can be.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch adds DP link training optimization by reusing the
previously trained values.

v2:
- rebase

V3:
- rebase

V4:
- when HPD long pulse is received, the flag is cleared
  that indicates if DP link training is required or not
  (based on Sivakumar's comment)
Signed-off-by: NMika Kahola <mika.kahola@intel.com>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is a first of series patches that optimize DP link
training. The first patch is for eDP only where we reuse
the previously trained link training values from cache
i.e. voltage swing and pre-emphasis levels.

In case we are not able to train the link by reusing
the known values, the link training parameters are set
to zero and training is restarted.

V2:
- flag that indicates if DP link is trained and valid
  renamed from 'link_trained' to 'train_set_valid'
- removed routine 'intel_dp_reuse_link_train'

V3:
- rebased against the latest drm-intel-nightly

V4:
- removed HPD long pulse handling for eDP case to clear the
  flag that indicates to reuse the current link training
  parameters. (based on Sivakumar's comment)
Signed-off-by: NMika Kahola <mika.kahola@intel.com>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
[danvet: s/DP/eDP/ in subject to make scope clear.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Based on the spec, Setting up static BIAS for GPU to improve the
rps performace.

v2: rename reg defn to match spec. (Ville)

v3: Updated bias setting for chv (Deepak)
Signed-off-by: NDeepak S <deepak.s@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We switched from calling i915_gem_alloc_context_obj() to calling
i915_gem_alloc_object() so the error handling needs to be updated to
check for NULL instead of IS_ERR().

Fixes: 149c86e7 ('drm/i915: Allocate context objects from stolen')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is the wrong layer to apply an arbitrary restriction and the wrong
error code (object too large!). If we do want to prevent large offsets
being return to the user on 32bit systems (to hide bugs in userspace),
you want to restrict the drm_mm range manager instead. This first tells
userspace about the correct size of the GTT they can use (so they don't
try and overallocate object or batches), and fixes the eviction logic to
avoid the eventual and *guaranteed* error.

Fixes regression in
commit d7b2633d
Author: Michel Thierry <michel.thierry@intel.com>
Date:   Wed Apr 8 12:13:34 2015 +0100

    drm/i915/gen8: Dynamic page table allocations
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Expose some more of our internal RPS bookkeeping for debugging.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Inspired by scripts/coccinelle/api/err_cast.cocci
Signed-off-by: NFabian Frederick <fabf@skynet.be>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Do not to clear mappings outside the allocated VMA under any
circumstances. Only clear the smaller of VMA or object page count.

This is required to allow creating partial object VMAs which in
turn are needed for partial GGTT views.
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Due to changes in the driver and to support Displayport compliance testing,
the test request and sink IRQ logic has been relocated from
intel_dp_check_link_status to intel_dp_detect. This is because the bulk of the
compliance tests that set the TEST_REQUEST bit in the DEVICE_IRQ field of the
DPCD issue a long pulse / hot plug event to signify the start of the test.
Currently, for a long pulse, intel_dp_check_link_status is not called for a
long HPD pulse, so if test requests come in, they cannot be detected by the
driver.

Once located in the intel_dp_detect, in the regular hot plug event path,
proper detection of Displayport compliance test requests occurs which then
invokes the test handler to support them. Additionally, this places compliance
testing in the normal operational paths, eliminating as much special case code
as possible.

The only change in intel_dp_check_link_status with this patch is that when
the IRQ is the result of a test request from the sink, the test handler is not
invoked during the short pulse path. Short pulse test requests are for a
particular variety of tests (mainly link training) that will be implemented
in the future. Once those tests are available, the test request handler will
be called from here as well.

V2:
- Rewored the commit message to be more clear about the content and intent
  of this patch
- Restore IRQ detection logic to intel_dp_check_link_status(). Continue to
  detect and clear sink IRQs in the short pulse case. Ignore test requests
  in the short pulses for now since they are for future test implementations.
Signed-off-by: NTodd Previte <tprevite@gmail.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Enable runtime PM for Skylake platform

v2: After adding dmc ver 1.0 support rebased on top of nightly. (Animesh)

Issue: VIZ-2819
Signed-off-by: NA.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: NSuketu Shah <suketu.j.shah@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NAnimesh Manna <animesh.manna@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Warn if the conditions to enter or exit DC6 are not satisfied such
as support for runtime PM, state of power well, CSR loading etc.

v2: Removed camelcase in functions and variables.

v3: Do some minimal check to assert if CSR program is not loaded.

v4:
1] Correct the check for backlight-disabling in assert_can_enable_dc6().
2] Check csr.loaded = false before disabling DC6 and simplify other checks.

v5:
1] Remove checks for DC5 state from assert_can_enable_dc6 function as DC5 is no
   longer enabled before enabling DC6.
2] Correct the check for CSR-loading in assert_can_disable_dc6 function as CSR must
   be loaded for context restore to happen on DC6 disabling.

v6:
1] It's okay to explicitly disable DC6 during driver-load/resume even though it might
   already be disabled and so don't warn about it.

v7: Rebase to latest.

v8: Sqashed the patch from Imre -
[PATCH] drm/i915/skl: avoid false CSR fw not loaded WARN during driver load/resume

v9: After adding dmc ver 1.0 support rebased on top of nightly. (Animesh)

v10: During initialization added a early return before disabling DC5. (Animesh)

Issue: VIZ-2819
Signed-off-by: NA.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: NSuketu Shah <suketu.j.shah@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NAnimesh Manna <animesh.manna@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch just implements the basic enable and disable
functions of DC6 state which is needed for SKL platform.

Its important to load SKL CSR program before calling enable.

DC6 is a deeper power saving state where hardware dynamically
disables power well 0 and saves the associated registers.
DC6 can be entered when software allows it, the conditions
for DC5 are met, and the PCU allows DC6.
DC6 cannot be used if the backlight is being driven from the
display utility pin.

Its better to configure display engine to have power well 2
disabled before getting into DC6 enable function. Hence rpm
framework will ensure to check status of power well 2 and DC5
before calling skl_enable_dc6.

v2: Replace HAS_ with IS_ check as per Daniel's review comments

v3: Cleared the bits dc5/dc6 enable of DC_STATE_EN register
before setting them as per Satheesh's review comments.

v4: No need to call gen9_disable_dc5 inside enable sequence of
DC6, as its already take care above.

v5: call POSTING_READ for every write to a register to ensure that
its written immediately.
Call intel_prepare_ddi during DC6 exit as it's required on low-power exit.

v6: Protect DC6-enabling-disabling functionality with locks to synchronize
with CSR-loading code.

v7: Remove grabbing CSR-related mutex in skl_enable/disable_dc6 functions as
    deferred DC5-enabling functionality is now removed.

v8: Remove 'Disabling DC5' from the debug comment during DC6 enabling as when
    DC6 is allowed, DC5 is not programmed at all.

v9:
- Rebase to latest.
- Move all DC6-related functions from intel_display.c to intel_runtime_pm.c.

v10: After adding dmc ver 1.0 support rebased on top of nightly. (Animesh)

Issue: VIZ-2819
Signed-off-by: NA.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NAnimesh Manna <animesh.manna@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add triggers for DC6 as per details provided in skl_enable_dc6
and skl_disable_dc6 implementations.

Also Call POSTING_READ for every write to a register to ensure
it is written to immediately

v1: Remove POSTING_READ and intel_prepare_ddi calls as they've been added in previous patches.

v2:
1] Remove check for backlight disabled as it should be the case by that time.
2] Mark DC5 as disabled when enabling DC6.
3] Return from DC5-disabling function early if DC5 is already be disabled which can happen
   due to DC6-enabling earlier.
3] Ensure CSR firmware is loaded after resume from DC6 as corresponding memory contents won't
   be retained after runtime-suspend.
4] Ensure that CSR isn't identified as loaded before CSR-loading program is called during
   runtime-resume.

v3: Rebase to latest
Modified as per review comments from Imre and after discussion with Art:
1] DC6 should be preferably enabled when PG2 is disabled by SW as the check for PG1 being
   disabled is taken of by HW to enter DC6, and disabled when PG2 is enabled respectively.
   This helps save more power, especially in the case when display is disabled but GT is
   enabled. Accordingly, replacing DC5 trigger sequence with DC6 for SKL.
2] DC6 could be enabled from intel_runtime_suspend() function, if DC5 is already enabled.
3] Move CSR-load-status setting code from intel_runtime_suspend function to a new function.

v4:
1] Enable/disable DC6 only when toggling the power-well using a newly defined macro ENABLE_DC6.

v5:
1] Load CSR on system resume too as firmware may be lost on system suspend preventing
   enabling DC5, DC6.
2] DDI buffers shouldn't be programmed during driver-load/resume as it's already done
   during modeset initialization then and also that the encoder list is still uninitialized by
   then. Therefore, call intel_prepare_ddi function right after disabling DC6 but outside
   skl_disable_dc6 function and not during driver-load/resume.

v6:
1] Rebase to latest.
2] Move SKL_ENABLE_DC6 macro definition from intel_display.c to intel_runtime_pm.c.

v7:
1) Refactored the code for removing the warning got from checkpatch.
2) After adding dmc ver 1.0 support rebased on top of nightly. (Animesh)

v8:
- Reverted the changes done in v7.
- Removed the condition check in skl_prepare_resune(). (Animesh)

Issue: VIZ-2819
Signed-off-by: NA.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: NSuketu Shah <suketu.j.shah@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NAnimesh Manna <animesh.manna@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Warn if the conditions to enter or exit DC5 are not satisfied such
as support for runtime PM, state of power well, CSR loading etc.

v2: Removed camelcase in functions and variables.

v3: Do some minimal check to assert if CSR program is not loaded.

v4:
1] Used an appropriate function lookup_power_well() to identify power well,
instead of using a magic number which can change in future.
2] Split the conditions further in assert_can_enable_DC5() and added more checks.
3] Removed all WARNs from assert_can_disable_DC5 as they were unnecessary and added two
   new ones.
4] Changed variable names as updated in earlier patches.

v5:
1] Change lookup_power_well function to take an int power well id.
2] Define a new intel_display_power_well_is_enabled helper function to check whether a
   particular power well is enabled.
3] Use CSR-related mutex in assert_csr_loaded function.

v6: Remove use of dc5_enabled variable as it's no longer needed.

v7:
1] Rebase to latest.
2] Move all DC5-related functions from intel_display.c to intel_runtime_pm.c.

v8: After adding dmc ver 1.0 support rebased on top of nightly. (Animesh)

v9: Modified below changes based on review comments from Imre.
- Moved intel_display_power_well_is_enabled() to intel_runtime_pm.c.
- Removed mutex lock from assert_csr_loaded(). (Animesh)

Issue: VIZ-2819
Signed-off-by: NA.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: NSuketu Shah <suketu.j.shah@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NAnimesh Manna <animesh.manna@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch just implements the basic enable and disable
functions of DC5 state which is needed for both SKL and BXT.

Its important to load respective CSR program before calling
enable, which anyways will happen as CSR program is executed
during boot.

DC5 is a power saving state where hardware dynamically disables
power well 1 and the CDCLK PLL and saves the associated registers.

DC5 can be entered when software allows it, power well 2 is
disabled, and hardware detects that all pipes are disabled
or pipe A is enabled with PSR active.

Its better to configure display engine to have power well 2 disabled before
getting into DC5 enable function. Hence rpm framework will have to
ensure to check status of power well 2 before calling gen9_enable_dc5.

Rather dc5 entry criteria should be decided based on power well 2 status.
If disabled, then call gen9_enable_dc5.

v2: Replace HAS_ with IS_ check as per Daniel's review comments

v3: Cleared the bits dc5/dc6 enable of DC_STATE_EN register
before setting them as per Satheesh's review comments.

v4: call POSTING_READ for every write to a register to ensure that
its written immediately.

v5: Modified as per review comments from Imre.
- Squashed register definitions into this patch.
- Finetuned comments and functions.

v6:
Avoid redundant writes in gen9_set_dc_state_debugmask_memory_up function.

v7:
- Rebase to latest.
- Move all runtime PM functions defined in intel_display.c to
  intel_runtime_pm.c.

v8: Rebased to drm-intel-nightly. (Animesh)

Issue: VIZ-2819
Signed-off-by: NA.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NAnimesh Manna <animesh.manna@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add triggers as per expectations mentioned in gen9_enable_dc5
and gen9_disable_dc5 patch.

Also call POSTING_READ for every write to a register to ensure that
its written immediately.

v1: Remove POSTING_READ calls as they've already been added in previous patches.

v2: Rebase to move all runtime pm specific changes to intel_runtime_pm.c file.

Modified as per review comments from Imre:
1] Change variable name 'dc5_allowed' to 'dc5_enabled' to correspond to relevant
   functions.
2] Move the check dc5_enabled in skl_set_power_well() to disable DC5 into
   gen9_disable_DC5 which is a more appropriate place.
3] Convert checks for 'pm.dc5_enabled' and 'pm.suspended' in skl_set_power_well()
   to warnings. However, removing them for now as they'll be included in a future patch
   asserting DC-state entry/exit criteria.
4] Enable DC5, only when CSR firmware is verified to be loaded. Create new structure
   to track 'enabled' and 'deferred' status of DC5.
5] Ensure runtime PM reference is obtained, if CSR is not loaded, to avoid entering
   runtime-suspend and release it when it's loaded.
6] Protect necessary CSR-related code with locks.
7] Move CSR-loading call to runtime PM initialization, as power domains needed to be
   accessed during deferred DC5-enabling, are not initialized earlier.

v3: Rebase to latest.

Modified as per review comments from Imre:
1] Use blocking wait for CSR-loading to finish to enable DC5  for simplicity, instead of
   deferring enabling DC5 until CSR is loaded.
2] Obtain runtime PM reference during CSR-loading initialization itself as deferred DC5-
   enabling is removed and release it at the end of CSR-loading functionality.
3] Revert calling CSR-loading functionality to the beginning of i915 driver-load
   functionality to avoid any delay in loading.
4] Define another variable to track whether CSR-loading failed and use it to avoid enabling
   DC5 if it's true.
5] Define CSR-load-status accessor functions for use later.

v4:
1] Disable DC5 before enabling PG2 instead of after it.
2] DC5 was being mistaken enabled even when CSR-loading timed-out. Fix that.
3] Enable DC5-related functionality using a macro.
4] Remove dc5_enabled tracking variable and its use as it's not needed now.

v5:
1] Mark CSR failed to load where necessary in finish_csr_load function.
2] Use mutex-protected accessor function to check if CSR loaded instead of directly
   accessing the variable.
3] Prefix csr_load_status_get/set function names with intel_.

v6: rebase to latest.
v7: Rebase on top of nightly (Damien)
v8: Squashed the patch from Imre - added csr helper pointers to simplify the code. (Imre)
v9: After adding dmc ver 1.0 support rebased on top of nightly. (Animesh)
v10: Added a enum for different csr states, suggested by Imre. (Animesh)

v11: Based on review comments from Imre, Damien and Daniel following changes done
- enum name chnaged to csr_state (singular form).
- FW_UNINITIALIZED used as zeroth element in enum csr_state.
- Prototype changed for helper function(set/get csr status), using enum csr_state instead of bool.

v12: Based on review comment from Imre, introduced bool fw_loaded local to finish_csr_load() which helps
calling once to set the csr status. The same flag used to fail RPM if find any issue during
firmware loading.

Issue: VIZ-2819
Signed-off-by: NA.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: NSuketu Shah <suketu.j.shah@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NAnimesh Manna <animesh.manna@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Display Context Save and Restore support is needed for
various SKL Display C states like DC5, DC6.

This implementation is added based on first version of DMC CSR program
that we received from h/w team.

Here we are using request_firmware based design.
Finally this firmware should end up in linux-firmware tree.

For SKL platform its mandatory to ensure that we load this
csr program before enabling DC states like DC5/DC6.

As CSR program gets reset on various conditions, we should ensure
to load it during boot and in future change to be added to load
this system resume sequence too.

v1: Initial relese as RFC patch

v2: Design change as per Daniel, Damien and Shobit's review comments
request firmware method followed.

v3: Some optimization and functional changes.
Pulled register defines into drivers/gpu/drm/i915/i915_reg.h
Used kmemdup to allocate and duplicate firmware content.
Ensured to free allocated buffer.

v4: Modified as per review comments from Satheesh and Daniel
Removed temporary buffer.
Optimized number of writes by replacing I915_WRITE with I915_WRITE64.

v5:
Modified as per review comemnts from Damien.
- Changed name for functions and firmware.
- Introduced HAS_CSR.
- Reverted back previous change and used csr_buf with u8 size.
- Using cpu_to_be64 for endianness change.

Modified as per review comments from Imre.
- Modified registers and macro names to be a bit closer to bspec terminology
and the existing register naming in the driver.
- Early return for non SKL platforms in intel_load_csr_program function.
- Added locking around CSR program load function as it may be called
concurrently during system/runtime resume.
- Releasing the fw before loading the program for consistency
- Handled error path during f/w load.

v6: Modified as per review comments from Imre.
- Corrected out_freecsr sequence.

v7: Modified as per review comments from Imre.
Fail loading fw if fw->size%8!=0.

v8: Rebase to latest.

v9: Rebase on top of -nightly (Damien)

v10: Enabled support for dmc firmware ver 1.0.
According to ver 1.0 in a single binary package all the firmware's that are
required for different stepping's of the product will be stored. The package
contains the css header, followed by the package header and the actual dmc
firmwares. Package header contains the firmware/stepping mapping table and
the corresponding firmware offsets to the individual binaries, within the
package. Each individual program binary contains the header and the payload
sections whose size is specified in the header section. This changes are done
to extract the specific firmaware from the package. (Animesh)

v11: Modified as per review comemnts from Imre.
- Added code comment from bpec for header structure elements.
- Added __packed to avoid structure padding.
- Added helper functions for stepping and substepping info.
- Added code comment for CSR_MAX_FW_SIZE.
- Disabled BXT firmware loading, will be enabled with dmc 1.0 support.
- Changed skl_stepping_info based on bspec, earlier used from config DB.
- Removed duplicate call of cpu_to_be* from intel_csr_load_program function.
- Used cpu_to_be32 instead of cpu_to_be64 as firmware binary in dword aligned.
- Added sanity check for header length.
- Added sanity check for mmio address got from firmware binary.
- kmalloc done separately for dmc header and dmc firmware. (Animesh)

v12: Modified as per review comemnts from Imre.
- Corrected the typo error in skl stepping info structure.
- Added out-of-bound access for skl_stepping_info.
- Sanity check for mmio address modified.
- Sanity check added for stepping and substeppig.
- Modified the intel_dmc_info structure, cache only the required header info. (Animesh)

v13: clarify firmware load error message.
The reason for a firmware loading failure can be obscure if the driver
is built-in. Provide an explanation to the user about the likely reason for
the failure and how to resolve it. (Imre)

v14: Suggested by Jani.
- fix s/I915/CONFIG_DRM_I915/ typo
- add fw_path to the firmware object instead of using a static ptr (Jani)

v15:
1) Changed the firmware name as dmc_gen9.bin, everytime for a new firmware version a symbolic link
with same name will help not to build kernel again.
2) Changes done as per review comments from Imre.
- Error check removed for intel_csr_ucode_init.
- Moved csr-specific data structure to intel_csr.h and optimization done on structure definition.
- fw->data used directly for parsing the header info & memory allocation
only done separately for payload. (Animesh)

v16:
- No need for out_regs label in i915_driver_load(), so removed it.
- Changed the firmware name as skl_dmc_ver1.bin, followed naming convention <platform>_dmc_<api-version>.bin (Animesh)

Issue: VIZ-2569
Signed-off-by: NA.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NAnimesh Manna <animesh.manna@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

i915_needs_cmd_parser already checks that for us.
Suggested-by: NMika Kuoppala <mika.kuoppala@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

Signed-off-by: NNick Hoath <nicholas.hoath@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch enables skylake sprite plane display scaling using shared
scalers atomic desgin.

v2:
-use single copy of scaler limits (Matt)

v3:
-detaching scalers moved to crtc commit path (Matt)

v4:
-changes to align with updated scaler structures (Matt, me)
-keep sprite src rect in 16.16 format (Matt, Daniel)

v5:
-rebased on top of 90/270 rotation changes (me)
-Refactored skl_update_plane to reduce its size (Daniel)
 It is a step towards having a single function covering all planes.
Signed-off-by: NChandra Konduru <chandra.konduru@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Testcase: igt/kms_plane_scaling
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch enables skylake primary plane scaling using shared
scalers atomic desgin.

v2:
-use single copy of scaler limits (Matt)

v3:
-move detach_scalers to crtc commit path (Matt)
-use values in plane_state->src as regular integers (me)

v4:
-changes to align with updated scaler structures (Matt, me)
-keep plane src rect in 16.16 format (Matt, Daniel)

v5:
-Rebased on top of 90/270 rotation changes (me)
-Fixed an issue introduced by 90/270 changes where plane programming
 is using drm_plane->state rect instead of intel_plane->state rect.
 This change also required for scaling to work properly. (me)
-With 90/270, updated limits to cover both portrait and landscape usages (me)
-Refactored skylake_update_primary_plane to reduce its size (Daniel)
 Added helper functions for refactoring are comprehended enough to be
 used for skylake_update_plane (for sprite) too. One stop towards
 having single function for all planes.

v6:
-Added fixme note when checking plane_state->src width in update_plane (Daniel)
-Release lock when failing to colorkey request with active scaler (Daniel)
Signed-off-by: NChandra Konduru <chandra.konduru@intel.com>
Reviewed-by: matthew.d.roper@intel.com
Reviewed-by: sonika.jindal@intel.com (v5)
Testcase: igt/kms_plane_scaling
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Merge tag 'drm-intel-next-2015-04-23-fixed' of git://anongit.freedesktop.org/drm-intel into drm-next

drm-intel-next-2015-04-23:
- dither support for ns2501 dvo (Thomas Richter)
- some polish for the gtt code and fixes to finally enable the cmd parser on hsw
- first pile of bxt stage 1 enabling (too many different people to list ...)
- more psr fixes from Rodrigo
- skl rotation support from Chandra
- more atomic work from Ander and Matt
- pile of cleanups and micro-ops for execlist from Chris
drm-intel-next-2015-04-10:
- cdclk handling cleanup and fixes from Ville
- more prep patches for olr removal from John Harrison
- gmbus pin naming rework from Jani (prep for bxt)
- remove ->new_config from Ander (more atomic conversion work)
- rps (boost) tuning and unification with byt/bsw from Chris
- cmd parser batch bool tuning from Chris
- gen8 dynamic pte allocation (Michel Thierry, based on work from Ben Widawsky)
- execlist tuning (not yet all of it) from Chris
- add drm_plane_from_index (Chandra)
- various small things all over

* tag 'drm-intel-next-2015-04-23-fixed' of git://anongit.freedesktop.org/drm-intel: (204 commits)
  drm/i915/gtt: Allocate va range only if vma is not bound
  drm/i915: Enable cmd parser to do secure batch promotion for aliasing ppgtt
  drm/i915: fix intel_prepare_ddi
  drm/i915: factor out ddi_get_encoder_port
  drm/i915/hdmi: check port in ibx_infoframe_enabled
  drm/i915/hdmi: fix vlv infoframe port check
  drm/i915: Silence compiler warning in dvo
  drm/i915: Update DRIVER_DATE to 20150423
  drm/i915: Enable dithering on NatSemi DVO2501 for Fujitsu S6010
  rm/i915: Move i915_get_ggtt_vma_pages into ggtt_bind_vma
  drm/i915: Don't try to outsmart gcc in i915_gem_gtt.c
  drm/i915: Unduplicate i915_ggtt_unbind/bind_vma
  drm/i915: Move ppgtt_bind/unbind around
  drm/i915: move i915_gem_restore_gtt_mappings around
  drm/i915: Fix up the vma aliasing ppgtt binding
  drm/i915: Remove misleading comment around bind_to_vm
  drm/i915: Don't use atomics for pg_dirty_rings
  drm/i915: Don't look at pg_dirty_rings for aliasing ppgtt
  drm/i915/skl: Support Y tiling in MMIO flips
  drm/i915: Fixup kerneldoc for struct intel_context
  ...

Conflicts:
	drivers/gpu/drm/i915/i915_drv.c

Completely different approach:  Instead of encoding each and every
framebuffer update as spice operation simply update the shadow
framebuffer and maintain a dirty rectangle.  Also schedule a worker
to push an update for the dirty rectangle as spice operation.  Usually
a bunch of dirty rectangle updates are collected before the worker
actually runs.

What changes:  Updates get batched now.  Instead of sending tons of
small updates a few large ones are sent.  When the same region is
updated multiple times within a short timeframe (scrolling multiple
lines for example) we send a single update only.  Spice server has an
easier job now:  The dependency tree for display operations which spice
server maintains for lazy rendering is alot smaller now.  Spice server's
image compression probably works better too with the larger image blits.

Net effect:  framebuffer console @ qxldrmfb is an order of magnitude
faster now.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

misc drm core patches.

* tag 'topic/drm-misc-2015-05-06' of git://anongit.freedesktop.org/drm-intel:
  drm: simplify master cleanup
  drm: simplify authentication management
  drm: drop unused 'magicfree' list
  drm: fix a memleak on mutex failure path
  drm/atomic-helper: Really recover pre-atomic plane/cursor behavior
  drm/qxl: Fix qxl_noop_get_vblank_counter()
  drm: Zero out invalid vblank timestamp in drm_update_vblank_count. (v2)
  drm: Prevent invalid use of vblank_disable_immediate. (v2)
  drm/vblank: Fixup and document timestamp update/read barriers
  DRM: Don't re-poll connector for disconnect
  drm: Fix for DP CTS test 4.2.2.5 - I2C DEFER handling
  drm: Fix the 'native defer' message in drm_dp_i2c_do_msg()
  drm/atomic-helper: Don't call atomic_update_plane when it stays off

In drm_master_destroy() we _free_ the master object. There is no reason to
hold any locks while dropping its static members, nor do we have to reset
it to 0.

Furthermore, kfree() already does NULL checks, so call it directly on
master->unique and drop the redundant reset-code.
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The magic auth tokens we have are a simple map from cyclic IDs to drm_file
objects. Remove all the old bulk of code and replace it with a simple,
direct IDR.

The previous behavior is kept. Especially calling authmagic multiple times
on the same magic results in EINVAL except on the first call. The only
difference in behavior is that we never allocate IDs multiple times as
long as a client has its FD open.

v2:
 - Fix return code of GetMagic()
 - Use non-cyclic IDR allocator
 - fix off-by-one in "magic > INT_MAX" sanity check

v3:
 - drop redundant "magic > INT_MAX" check
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>