Added variable 'error' to struct dvb_ringbuffer, which is set to zero on
init() and flush(). Also reset read an write pointers to zero on flush()
to get less fragmented data.
Signed-off-by: NAndreas Oberritter <obi@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch fixes default values for some picture controls:
 - brightness set to 50% by default (now is 0%)
 - hue set to 50% by default (now is 0%)
 - sets saturation to datasheet value
 - volume set to 0dB (now is -32dB)
and some left small fixes:
 - twice offset adding
 - balance didn't follow datasheet (bits[0:5] = attenuation;
   bit[6] = channel to provide attenuation)
Signed-off-by: NMarcin Rudowski <mar_rud@poczta.onet.pl>
Signed-off-by: NIan Pickworth <ian@pickworth.me.uk>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch adds support for the IR remote control found in the card
CX88_BOARD_PROLINK_PLAYTVPVR.
Signed-off-by: NMatheus Izvekov <mizvekov@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch changes the gpio0 values for the card CX88_BOARD_PROLINK_PLAYTVPVR
to the ones observed using RegSpy from the dscaler project.
Signed-off-by: NMatheus Izvekov <mizvekov@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- Added support for AVerMedia A169 Dual Analog tuner card
  (dual saa7134 decoders - only 1 working right now)
- Added autodetection for both parts of the card.
  It shows up like 2 cards, B1 and B
- Enabled tuner B1, SVIDEO on B1 and composite1 through SVIDEO,
  FIXME: B is more or less dead at this point and I suspect the
  FM-radio is on the B part of the board
Signed-off-by: NRickard Osser <ricky@osser.se>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- added tuner_lg_taln_pal_secam_ranges
- renamed tuner 66 from TUNER_LG_NTSC_TALN_MINI to TUNER_LG_TALN
- updated FlyTV mini Asus Digimatrix with new tuner

Thanks-to: Rickard Osser <ricky@osser.se>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- matched indents on quotes within a printk
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- added missing "count" element in Thomson FE6600
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Some chipsets have several problems when pci to pci transfers are activated
on overlay mode. the option no_overlay allows disabling such feature of
the driver, in favor of keeping the system stable.
The default is to use pcipci_fail flag defined on drivers/pci/quirks.c.
It also allows the user to override it by forcing disable overlay or forcing
enable. Forcing enable may generate PCI transfer corruption, including disk
mass corruption, so should be used with care.
Added a text description to this option and make messages looks the same at
both bttv and saa7134 drivers.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Used Lindent, manually changed some line breaks. Removed invalid email
addresses, useless casts and useless initialization of return values.
Signed-off-by: NAndreas Oberritter <obi@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Rename 'enum dmxdevype' to 'enum dmxdev_type' and use this enum instead
of int for the member 'type' of struct dmxdev_filter.
Signed-off-by: NAndreas Oberritter <obi@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The member dvbdev gets initialized once but is never used after that.
Signed-off-by: NAndreas Oberritter <obi@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The PID value is already stored in struct dmx_sct_filter_params which is
a member of struct dmxdev_filter.
Acked-by: NJohannes Stezenbach <js@linuxtv.org>
Signed-off-by: NAndreas Oberritter <obi@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Old values generally works in A2 mono, but new ones allows:
- detect and use Nicam stereo
- mute in tv
- use radio FM
Signed-off-by: NMarcin Rudowski <mar_rud@poczta.onet.pl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Also Removed whitespaces introduced by previous tena patch
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

There is an error in the cx88 code that causes this message in the syslog when
balance is changed at full volume:
Mar  4 18:35:08 ian2 kernel: cx88[0]: irq pci [0x1] vid*
Mar  4 18:35:39 ian2 last message repeated 348 times
Mar  4 18:36:01 ian2 last message repeated 564 times
... and so on
The attached patch cures this problem.
Signed-off-by: NIan Pickworth <ian@pickworth.me.uk>
Signed-off-by: NMarcin Rudowski <mar_rud@poczta.onet.pl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The Coverity checker (previously Stanford checker) noticed that
the value of nskips could be read even if it was never written.
Signed-off-by: NDuncan Sands <baldrick@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Radio now works.
Tuner now supports both PAL/D and STD/MN models
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Conflicts:
	Documentation/video4linux/CARDLIST.cx88
	drivers/media/video/cx88/Kconfig
	drivers/media/video/em28xx/em28xx-video.c
	drivers/media/video/saa7134/saa7134-dvb.c

Resolved as in the original merge by Mauro Carvalho Chehab

This address is going to be obsolete, so I should update it.

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] SB1: Check for -mno-sched-prolog if building corelis debug kernel.
  [MIPS] Sibyte: Fix race in sb1250_gettimeoffset().
  [MIPS] Sibyte: Fix interrupt timer off by one bug.
  [MIPS] Sibyte: Fix M_SCD_TIMER_INIT and M_SCD_TIMER_CNT wrong field width.
  [MIPS] Protect more of timer_interrupt() by xtime_lock.
  [MIPS] Work around bad code generation for <asm/io.h>.
  [MIPS] Simple patch to power off DBAU1200
  [MIPS] Fix DBAu1550 software power off.
  [MIPS] local_r4k_flush_cache_page fix
  [MIPS] SB1: Fix interrupt disable hazard.
  [MIPS] Get rid of the IP22-specific code in arclib.
  Update MAINTAINERS entry for MIPS.

The 40-bit DMA workaround recently implemented for 5714, 5715, and
5780 needs to be expanded because there may be other tg3 devices
behind the EPB Express to PCIX bridge in the 5780 class device.

For example, some 4-port card or mother board designs have 5704 behind
the 5714.

All devices behind the EPB require the 40-bit DMA workaround.

Thanks to Chris Elmquist again for reporting the problem and testing
the patch.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the AX.25 dialect chosen by the sysadmin is set to DAMA master / 3
(or DAMA slave / 2, if CONFIG_AX25_DAMA_SLAVE=n) ax25_kick() will fall
through the switch statement without calling ax25_send_iframe() or any
other function that would eventually free skbn thus leaking the packet.

Fix by restricting the sysctl inferface to allow only actually supported
AX.25 dialects.

The system administration mistake needed for this to happen is rather
unlikely, so this is an uncritical hole.

Coverity #651.
Signed-off-by: NRalf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VIDEO_CX88_ALSA should not be between VIDEO_CX88_DVB and
VIDEO_CX88_DVB_ALL_FRONTENDS

When cx88-alsa was added to cx88/Kconfig, it was added in between
VIDEO_CX88_DVB and VIDEO_CX88_DVB_ALL_FRONTENDS.  This caused
undesireable effects to the appearance of the menu options in
menuconfig.

This fix reorders cx88-alsa and cx88-dvb in Kconfig, to match saa7134,
and restore the correct menuconfig appearance.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fixed em28xx based system lockup, device needs to be initialized before
starting the isoc transfer otherwise the system will completly lock up.
Signed-off-by: NMarkus Rechberger <mrechberger@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

sys_unshare() does mmput(new_mm).  This is not enough if we have
mm->core_waiters.

This patch is a temporary fix for soon to be released 2.6.16.
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
[ Checked with Uli: "I'm not planning to use unshare(CLONE_VM).  It's
  not needed for any functionality planned so far.  What we (as in Red
  Hat) need unshare() for now is the filesystem side." ]
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
From Dave Johnson <djohnson+linuxmips@sw.starentnetworks.com>:
    
sb1250_gettimeoffset() simply reads the current cpu 0 timer remaining
value, however once this counter reaches 0 and the interrupt is raised,
it immediately resets and begins to count down again.
    
If sb1250_gettimeoffset() is called on cpu 1 via do_gettimeofday() after
the timer has reset but prior to cpu 0 processing the interrupt and
taking write_seqlock() in timer_interrupt() it will return a full value
(or close to it) causing time to jump backwards 1ms. Once cpu 0 handles
the interrupt and timer_interrupt() gets far enough along it will jump
forward 1ms.
    
Fix this problem by implementing mips_hpt_*() on sb1250 using a spare
timer unrelated to the existing periodic interrupt timers. It runs at
1Mhz with a full 23bit counter.  This eliminated the custom
do_gettimeoffset() for sb1250 and allowed use of the generic
fixed_rate_gettimeoffset() using mips_hpt_*() and timerhi/timerlo.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
From Dave Johnson <djohnson+linuxmips@sw.starentnetworks.com>:
    
The timers need to be loaded with 1 less than the desired interval not
the interval itself.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
From Dave Johnson <djohnson+linuxmips@sw.starentnetworks.com>:
    
Field width should be 23 bits not 20 bits.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
From Dave Johnson <djohnson+linuxmips@sw.starentnetworks.com>:

* do_timer() expects the arch-specific handler to take the lock as it
  modifies jiffies[_64] and xtime.
* writing timerhi/lo in timer_interrupt() will mess up
  fixed_rate_gettimeoffset() which reads timerhi/lo.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
If a call to set_io_port_base() was being followed by usage of
mips_io_port_base in the same function gcc was possibly using the old
value due to some clever abuse of const.  Adding a barrier will keep
the optimization and result in correct code with latest gcc.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NMatej Kupljen <matej.kupljen@ultra.si>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
If dcache_size != icache_size or dcache_size != scache_size, or
set-associative cache, icache/scache does not flushed properly.  Make
blast_?cache_page_indexed() masks its index value correctly.  Also,
use physical address for physically indexed pcache/scache.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
The SB1 core has a three cycle interrupt disable hazard but we were
wrongly treating it as fully interlocked.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
This breaks the kernel build if sgiwd93 was configured as a module.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>