Si4713 FM transmitter on Nokia RX-51/N900 is connected to same Line out
signals of TLV320AIC34 than TPA6130 headphone amplifier.

This patch adds route to transmitter and "FM Transmitter" control to keep
route active when needed.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

It is more usefull to report headset instead of video out cable in response
to jack insertion as this is more usual use-case and because now the headset
feature is supported. Automatic accessory detection is not possible at the
moment so most sensible static accessory type have to be used.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

This patch adds support for headset microphone in Nokia RX-51/N900. The mic
signal from audio jack is routed to codec A LINE1L via two switches and the
mic bias is coming from codec B part.

First switch is the tv-out switch that is already supported and the second
switch selects between voltage detection circuit and codecs. As there is
no use for voltage detection at the moment the second switch is connected
statically to codecs in rx51_soc_init.

Headset can be active when control "Jack Function" is set to "Headset".
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Just slight cleanup to be sync with upcoming change.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Merge branch 'for-2.6.39' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/asoc-2.6 into for-2.6.39

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Make the format of the codec_reg file more easily parsable.  Remove
the header field which gives the codec name.  These changes are important
when it comes to extend the debugfs codec_reg file to dump more than
PAGE_SIZE bytes to make it easier to calculate offsets within the
file.

We still need to handle the case when the snd_soc_read() call fails
and <no data: %d> is outputted.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add fields to describe all the audio-related GPIOs on Harmony, except for
the codec's GPIO IRQ, which will be passed in its i2c_board_info.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The CX20442 codec driver never provided the snd_soc_codec_driver's
.reg_cache_default member. With the latest ASoC framework changes, it
seems to be referred unconditionally, resulting in a NULL pointer
dereference if missing. Provide it.

Created and tested on Amstrad Delta against linux-2.6.38-rc2
Signed-off-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The Amstrad Delta ASoC driver used to override the digital_mute()
callback, expected to be not provided by the on-board CX20442 CODEC
driver, with its own implementation. While this is still posssible when
substituting the whole empty snd_soc_dai_driver.ops member (the CX20442
case), replacing snd_soc_dai_ops.digital_mute only is no longer correct
after the snd_soc_dai_driver.ops member has been constified, and results
in build error.

Drop this actually not used code path in hope the CX20442 driver never
provides its own snd_soc_dai_ops structure.

Created and tested against linux-2.6.38-rc2
Signed-off-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

gpio_set_value* should accept logic values not just 0 or 1. The WM8903 GPIO
driver has been fixed to work this way, so remove the redundant !!
previously required when it didn't accept values >1.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Earphone in Nokia RX-51/N900 is connected to left HP output of B part of the
TLV320AIC34 dual codec. In RX-51 the codec A is used as a traditional codec
and the codec B as an auxiliary device.

Audio from codec A goes via the codec B to earphone:
MONO_LOUT of A -> LINE2R of B (B interconnects) -> HPLOUT of B -> Earphone.

Take earphone into use by utilizing the recent ASoC auxiliary and
cross-device support.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

This driver does not use any of the functionality provided by the scoop
hardware.  Remove the unneeded header.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Instead, have the machine driver provide storage for the utility data
somehow.

For Harmony in particular, store this within struct tegra_harmony, itself
referenced by snd_soc_card's drvdata.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Indent with TABs not spaces.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add DAPM widget definitions for the internal speaker paths. Currently, this
path is always enabled while playback is active.

Add code to control the speaker amplifier GPIO.

The GPIO is requested during _init, since that's the first time it is
guaranteed that the WM8903 module is loaded, probed, and hence has exported
its GPIO chip.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Previously, snd-soc-tegra-harmony internally instantiated a platform device
object whenever the module was loaded. Instead, switch to a more typical model
where arch/arm/mach-tegra defines a platform device, and snd-soc-tegra-harmony
acts as a driver for such a platform device.

Define a new struct tegra_harmony to store driver data in the future.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

All ASoC cards need snd_soc_initialize_card_lists called. Previously, it was
only called for cards backed by a "soc-audio" platform device, via
soc_probe(). However, it's also needed for cards backed by other platform
devices, and registered directly via snd_soc_register_card().
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This configures the capture unused pins
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NHarsha Priya <priya.harsha@intel.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NHarsha Priya <priya.harsha@intel.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds the support for capture path in sn95031 codec.
This codec supports upto 6DMICs, 2 AMICs and Linein. The linein and AMICs
are connected through a MUX to ADC. The TX paths can be assigned to any of the
ADCs or DMICs.
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NHarsha Priya <priya.harsha@intel.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Provide driver data for cards within the card structure. To simplify the
implementation of the PM operations we don't use the struct device driver
data as this is used by the core to retrieve the card in callbacks from
the device model and PM core.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

snd_soc_dapm_put_volsw() has variables for both the unshifted and
shifted mask for updates commit 97404f (ASoC: Do DAPM control updates in
the middle of DAPM sequences) got confused between the two of these.
Since there's no need to keep a copy of the unshifted mask fix this and
simplify the code by using only one mask variable.

[Completely rewrote the changelog to describe the issue -- broonie.]
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Commit f6c2ed5d "ASoC: Fix the device references to codec and platform drivers"
moved codec and platform driver refcount increments from soc_bind_dai_link
to more appropriate places.

Adjust a little them so that refcounts are incremented before executing the
driver probe functions.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Harsha Priya <priya.harsha@intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch fixes the Kernel panic issue on accessing davinci_vc in
cq93vc_probe function. struct davinci_vc is part of platform device's
private driver data(codec->dev->p->driver_data) and this is populated
by DaVinci Voice Codec MFD driver.
Signed-off-by: NManjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Audio jack in Nokia RX-51/N900 is driven by TPA6130 headphone amplifier.
This patch adds support for it and stereo output can be active when
"Jack Function" == "TV-OUT" || "Headphone".

As the TPA6130 can output very high volume levels the output is limited
with snd_soc_limit_volume. Limiting value is found from Maemo kernel sources.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Allows drivers to distinguish which subsequence is being notified when
they get called back.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Could just as well live in sysfs but sysfs doesn't have the simple
value export helpers debugfs does.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Allow hookup of cards registered directly with the core to the PM
operations by exporting the device power management operations to
modules, also exporting the default PM operations since it is
expected that most cards will end up using exactly the same setup.

Note that the callbacks require that the driver data for the card be
the snd_soc_card.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

In order to support cards instantiated without using soc-audio remove
the use of the platform device in the card probe() and remove() ops.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The platform device for the card is tied closely to the soc-audio
implementation which we're currently trying to remove in favour of
allowing cards to have their own devices. Begin removing it by
replacing it with the card in the suspend and resume callbacks we
give to cards, also taking the opportunity to remove the legacy
suspend types which are currently hard coded anyway.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Commit f6c2ed5d "ASoC: Fix the device references to codec and platform drivers"
moved codec driver refcount increments from soc_bind_dai_link into
soc_probe_codec.

However, the commit didn't remove try_module_get from soc_probe_aux_dev so
the auxiliary device reference counts are incremented twice as the
soc_probe_codec is called from soc_probe_aux_dev too.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NAlexander Sverdlin <subaparts@yandex.ru>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>