Factor out the polling of the interrupt status register whilst we wait
for boot done to allow the polling to be reused in other situations.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Future updates will require us to manually apply the register patch for
wm5102.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Only the lowest three bits contain device revision for WM5102, the high
bits have been repurposed.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

If we have a directly provided 32kHz clock unconditionally enable it,
substantial chip functionality relies on it so dynamic management is
not worthwhile.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

MCLK1 is not in the AoD power domain so if it is used as the 32kHz clock
source we need to hold a runtime PM reference to keep the device from going
into low power mode.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

If no irq_flags are passed in platform data then query the interrupt
controller for the trigger type and try to use that. This provides
default operation with a wider range of hardware and will be needed
for device tree support where the interrupt flags are configured on
the interrupt controller.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

If a GPIO is specified for the chip IRQ line then request it. This
improves support for systems that do not put pins into input mode when
used as interrupts.

Also use this GPIO when the primary IRQ is in edge triggered mode to
detect if we have handled pending interrupts in order to improve
robustness.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Allow the user to configure edge triggered IRQs, though we do not yet
fully handle new interrupts occurring while an interrupt is being handled.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

regmap has a very similar looking error, help identify where the error
comes from by changing the error message.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Make sure that we don't leave the device enabled needlessly.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

'patch_regs' cannot be used uninitialized in wm8994_device_init(),
because 'patch_regs' was already guarded by 'regmap_patch'.
Thus, that's a bogus warning.

Without this patch, the build warning happens as below:

drivers/mfd/wm8994-core.c: In function 'wm8994_i2c_probe':
drivers/mfd/wm8994-core.c:595:7: warning: 'patch_regs' may be used uninitialized in this function [-Wuninitialized]
drivers/mfd/wm8994-core.c:408:14: note: 'patch_regs' was declared here
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

'data' is a pointer and hence use NULL instead of 0.
Silences the following warning:
drivers/mfd/max77686.c:49:50: warning: Using plain integer as NULL pointer
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Cc: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

module_i2c_driver() removes some boilerplate and makes the code
simple.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Conflicts:
	drivers/mfd/ab8500-gpadc.c
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

When rtsx_pci_acquire_irq fails in rtsx_pci_probe, we forget to
disable an MSI (if we enabled it). This results in this warning on the
next attempt to load the module:
WARNING: at drivers/pci/msi.c:834 pci_enable_msi_block+0x2a4/0x2b0()
Hardware name: HP EliteBook 840 G1
Modules linked in: rtsx_pci(+) ...
Pid: 4056, comm: modprobe Tainted: G          I  3.8.0-9405-gd895cb1a-1-vanilla #1
Call Trace:
 [<ffffffff81045c6a>] warn_slowpath_common+0x7a/0xc0
 [<ffffffff81045cc5>] warn_slowpath_null+0x15/0x20
 [<ffffffff81302544>] pci_enable_msi_block+0x2a4/0x2b0
 [<ffffffffa05e335a>] rtsx_pci_probe+0x55a/0x720 [rtsx_pci]
...

So properly disable MSI in that case.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Move the AB8500 Kconfig fragment below the AB3100 so the
menuconfig menu gets hierarchically nested and looks nice.
Having the EZX PCAP in the middle disturbs the nice
hierarchical layout from kconfig.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch uses module_platform_driver_probe() macro which makes
the code smaller and simpler.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch uses module_platform_driver_probe() macro which makes
the code smaller and simpler.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch uses module_platform_driver_probe() macro which makes
the code smaller and simpler.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch augments the STMP driver to read the device id
from the stmpe-i2c dt alias if present.

Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: NGabriel Fernandez <gabriel.fernandez@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

If there is no interrupt property into stmpe node
then activate the no-irq mode by setting the irq
value to -1.

Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: NGabriel Fernandez <gabriel.fernandez@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch allow using syscon driver from the platform data, i.e.
possibility using driver on systems without oftree support.
For search syscon device from the client drivers,
"syscon_regmap_lookup_by_pdevname" function was added.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

DT node properties should not have "_". Replacing them by "-".
Signed-off-by: NJ Keerthy <j-keerthy@ti.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add Flat Device Tree support to the AS3711 MFD driver. This patch just
allows to bind the driver to I2C devices, instantiated from the DT.
DT support for AS3711 cell drivers will be added in separate drivers.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Reviwed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

CONFIG_MFD_CROS_EC requires CONFIG_MFD_CORE for a couple of functions that
are declared but not defined:

	ERROR: "mfd_remove_devices" [drivers/mfd/cros_ec.ko] undefined!
	ERROR: "mfd_add_devices" [drivers/mfd/cros_ec.ko] undefined!

Fix it by selecting CONFIG_MFD_CORE anytime CONFIG_MFD_CROS_EC is enabled.
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Acked-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

To silent those:

 CC [M]  drivers/mfd/cros_ec_spi.o
drivers/mfd/cros_ec_spi.c: In function ‘cros_ec_spi_receive_response’:
drivers/mfd/cros_ec_spi.c:123:5: warning: format ‘%d’ expects argument of type
‘int’, but argument 4 has type ‘long int’ [-Wformat]
drivers/mfd/cros_ec_spi.c:157:3: warning: format ‘%d’ expects argument of type
‘int’, but argument 6 has type ‘long int’ [-Wformat]
drivers/mfd/cros_ec_spi.c:181:2: warning: format ‘%d’ expects argument of type
‘int’, but argument 4 has type ‘long int’ [-Wformat]
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

In order to fix those, when all cros code is modular:

ERROR: "cros_ec_prepare_tx" [drivers/mfd/cros_ec_spi.ko] undefined!
ERROR: "cros_ec_register" [drivers/mfd/cros_ec_spi.ko] undefined!
ERROR: "cros_ec_remove" [drivers/mfd/cros_ec_spi.ko] undefined!
ERROR: "cros_ec_suspend" [drivers/mfd/cros_ec_spi.ko] undefined!
ERROR: "cros_ec_resume" [drivers/mfd/cros_ec_spi.ko] undefined!
ERROR: "cros_ec_register" [drivers/mfd/cros_ec_i2c.ko] undefined!
ERROR: "cros_ec_remove" [drivers/mfd/cros_ec_i2c.ko] undefined!
ERROR: "cros_ec_suspend" [drivers/mfd/cros_ec_i2c.ko] undefined!
ERROR: "cros_ec_resume" [drivers/mfd/cros_ec_i2c.ko] undefined!
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use the key-matrix layer to interpret key scan information from the EC
and inject input based on the FDT-supplied key map. This driver registers
itself with the ChromeOS EC driver to perform communications.

The matrix-keypad FDT binding is used with a small addition to control
ghosting.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NLuigi Semenzato <semenzato@chromium.org>
Signed-off-by: NVincent Palatin <vpalatin@chromium.org>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

We now have a binding which adds two parameters to the matrix keypad DT
node. This is separate from the GPIO-driven matrix keypad binding, and
unfortunately incompatible, since that uses row-gpios/col-gpios for the
row and column counts.

So the easiest option here is to provide a function for non-GPIO drivers
to use to decode the binding.

Note: We could in fact create an entirely separate structure to hold
these two fields, but it does not seem worth it, yet. If we have more
parameters then we can add this, and then refactor each driver to hold
such a structure.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com> (v2)
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This uses a SPI bus to talk to the ChromeOS EC. The protocol
is defined by the EC and is fairly simple, with a length byte,
checksum, command byte and version byte (to permit easy creation
of new commands).
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This uses an I2C bus to talk to the ChromeOS EC. The protocol
is defined by the EC and is fairly simple, with a length byte,
checksum, command byte and version byte (to permit easy creation
of new commands).
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NChe-Liang Chiou <clchiou@chromium.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This is the base EC implementation, which provides a high level
interface to the EC for use by the rest of the kernel. The actual
communcations is dealt with by a separate protocol driver which
registers itself with this interface.

Interrupts are passed on through a notifier.

A simple message structure is used to pass messages to the
protocol driver.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NChe-Liang Chiou <clchiou@chromium.org>
Signed-off-by: NJonathan Kliegman <kliegs@chromium.org>
Signed-off-by: NLuigi Semenzato <semenzato@chromium.org>
Signed-off-by: NOlof Johansson <olofj@chromium.org>
Signed-off-by: NVincent Palatin <vpalatin@chromium.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This file is included verbatim from the ChromeOS EC respository.
Ideally we would prefer to avoid changing it, to make it easier
to track this rapidly-changing file.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NChe-Liang Chiou <clchiou@chromium.org>
Signed-off-by: NVincent Palatin <vpalatin@chromium.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Pull slave-dmaengine fixes from Vinod Koul:
 "Two fixes for slave-dmaengine.

  The first one is for making slave_id value correct for dw_dmac and
  the other one fixes the endieness in DT parsing"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dw_dmac: adjust slave_id accordingly to request line base
  dmaengine: dw_dma: fix endianess for DT xlate function

Pull media fixes from Mauro Carvalho Chehab:
 "For a some fixes for Kernel 3.9:
   - subsystem build fix when VIDEO_DEV=y, VIDEO_V4L2=m and I2C=m
   - compilation fix for arm multiarch preventing IR_RX51 to be selected
   - regression fix at bttv crop logic
   - s5p-mfc/m5mols/exynos: a few fixes for cameras on exynos hardware"

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] [REGRESSION] bt8xx: Fix too large height in cropcap
  [media] fix compilation with both V4L2 and I2C as 'm'
  [media] m5mols: Fix bug in stream on handler
  [media] s5p-fimc: Do not attempt to disable not enabled media pipeline
  [media] s5p-mfc: Fix encoder control 15 issue
  [media] s5p-mfc: Fix frame skip bug
  [media] s5p-fimc: send valid m2m ctx to fimc_m2m_job_finish
  [media] exynos-gsc: send valid m2m ctx to gsc_m2m_job_finish
  [media] fimc-lite: Fix the variable type to avoid possible crash
  [media] fimc-lite: Initialize 'step' field in fimc_lite_ctrl structure
  [media] ir: IR_RX51 only works on OMAP2