- 30 4月, 2011 28 次提交
-
-
由 Don Fry 提交于
All agn devices use the same module parameter structure. Delete the indirection and access the structure diretly. Signed-off-by: NDon Fry <donald.h.fry@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Wey-Yi Guy 提交于
Correction for new 105 series devices Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Johannes Berg 提交于
New microcode versions use the good CRC threshold field differently, as a flag, and in that case we should set it to 1/0 instead of 1/65535 for an active/passive scan. The new behaviour is advertised by the uCode with a feature flag. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Wey-Yi Guy 提交于
No functional changes, separate the connect and disconnect sequences in RXON commit function, easier to read and understand. Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Wey-Yi Guy 提交于
The data structure is shared by all _agn devices, remove the reference to 5000 Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Wey-Yi Guy 提交于
Move rxon_assoc to static function from ops Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Johannes Berg 提交于
The WoWLAN resume code will have to essentially do a restart, but without going through the work struct. To support that, refactor the restart by splitting out the preparation code into a new function. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Johannes Berg 提交于
There are a few cases like the WoWLAN support I'm writing that require attempting to access the NIC when it is known that it might not be accessible, e.g. after the system woke up and the platform might have reset the device. To avoid messages in this case, introduce the new function iwl_grab_nic_access_silent(), it will only return an error status. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Johannes Berg 提交于
If a device error happens while the uCode is being loaded or initialised, we will attempt to restart the device (which will likely fail again, but that's not the issue here). During this new restart, we turn off the device, but as the uCode failed to initialise it already is turned off. As a consequence, grabbing NIC access will fail and cause excessive messages and hangs. To fix this issue, introduce a new status bit and only attempt to reprogram the device when it isn't already disabled. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Yogesh Ashok Powar 提交于
The tx_headroom required for mwl8k driver is 32 bytes and it can use the space for 802.11 header received from mac80211. mwl8k considers the smallest 802.11 frame (CTS2self of 10 bytes) that can be received from mac80211 to compute the extra_tx_headroom as 22 (32 - 10) bytes. When the wireless interface is part of bridge, this extra_tx_headroom requirement results in a memcpy in mac80211 (in function pskb_expand_head) for all the data frames needing L2 forwarding/bridging, when NET_SKB_PAD is defined as 32. This patch reduces the extra_tx_headroom by 8 bytes so that memcpy of data frames in mac80211 is avoided in this case. The resize will be required in driver for frames with 802.11 header size of less than 18 bytes. Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NPradeep Nemavat <pnemavat@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
Remove all the convoluted hacks in the driver and simplify things by making use of mac80211's LED triggers. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stanislaw Gruszka 提交于
We now use priv->mutex to serialize sync command, remove old priv->sync_cmd_mutex and add assertion that priv->mutex must be locked. Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stanislaw Gruszka 提交于
Check status bits with mutex taken, because when we wait for mutex unlock, status can change. Patch should also make remaining sync commands be send with priv->mutex taken. That will prevent execute these commands when we are currently reset firmware, what could possibly cause troubles. Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stanislaw Gruszka 提交于
We mark command as huge by using meta->flags from other (non huge) command, but flags can be possibly overridden, when non huge command is enqueued, what can lead to: WARNING: at lib/dma-debug.c:696 dma_debug_device_change+0x1a3/0x1f0() DMA-API: device driver has pending DMA allocations while released from device [count=1] To fix introduce additional CMD_MAPPED to mark command as mapped and serialize iwl_enqueue_hcmd() with iwl_tx_cmd_complete() using hcmd_lock. Serialization will also fix possible race conditions, because q->read_ptr, q->write_ptr are modified/used in parallel. Do not change callback, I did (and fixed) that mistake in iwlagn. Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stanislaw Gruszka 提交于
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stanislaw Gruszka 提交于
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stanislaw Gruszka 提交于
struct iwl_queue is not part of firmware interface, so __packed is not needed. Remove it since is may affect performance. Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stanislaw Gruszka 提交于
We never set STATUS_SCANNING in softwre scanning mode, disable_hw_scan check is unneeded. Correct debug message while at it. Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stanislaw Gruszka 提交于
Don't need to use conditional as ch->band is already assigned to IEEE80211_BAND_5GHZ or IEEE80211_BAND_2GHZ Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stanislaw Gruszka 提交于
Add two below iwlwifi commits to iwlegacy: commit 554d1d02 Author: Stanislaw Gruszka <sgruszka@redhat.com> Date: Thu Dec 23 12:38:21 2010 +0100 iwlagn: enable only rfkill interrupt when device is down commit 3dd823e6 Author: Don Fry <donald.h.fry@intel.com> Date: Sun Feb 6 09:29:45 2011 -0800 iwlagn: Re-enable RF_KILL interrupt when down Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stanislaw Gruszka 提交于
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stanislaw Gruszka 提交于
Since commit f844a709 Author: Stanislaw Gruszka <sgruszka@redhat.com> Date: Fri Jan 28 16:47:44 2011 +0100 iwlwifi: do not set tx power when channel is changing we set device tx power during initialization to priv->tx_power_next, which itself is initialized to minimum power. That changed default behaviour of driver. Previously we initialized device to transmit at maximum available power by default. Patch change again to previous behaviour and cleanup tx power initialization. Fortunately this is not critical fix, as mac80211 layer setup tx power lately to 14dB, hence device does not operate at minimal transmit power all the time. Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
Debugfs file location: <debugfs_mnt>/ieee80211/phy#/ath9k_htc/modal_eeprom Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
Debugfs file location: <debugfs_mnt>/ieee80211/phy#/ath9k_htc/base_eeprom Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 John W. Linville 提交于
CC [M] drivers/net/wireless/p54/eeprom.o drivers/net/wireless/p54/eeprom.c: In function ‘p54_parse_rssical’: drivers/net/wireless/p54/eeprom.c:494:8: warning: ‘freq’ may be used uninitialized in this function Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 John W. Linville 提交于
CC [M] drivers/net/wireless/mwifiex/join.o drivers/net/wireless/mwifiex/join.c: In function ‘mwifiex_cmd_802_11_associate’: drivers/net/wireless/mwifiex/join.c:119:8: warning: ‘tsf_val’ may be used uninitialized in this function drivers/net/wireless/mwifiex/join.c:103:12: note: ‘tsf_val’ was declared here Looks like a copy-n-paste error, identical lines are a few lines below the ones removed, with an actual memcpy to tsf_val in between... Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 John W. Linville 提交于
CC [M] drivers/net/wireless/b43/phy_n.o drivers/net/wireless/b43/phy_n.c: In function ‘b43_nphy_set_channel’: drivers/net/wireless/b43/phy_n.c:3848:47: warning: ‘tabent_r2’ may be used uninitialized in this function drivers/net/wireless/b43/phy_n.c:3849:47: warning: ‘tabent_r3’ may be used uninitialized in this function drivers/net/wireless/b43/phy_n.c: In function ‘b43_nphy_poll_rssi.clone.14’: drivers/net/wireless/b43/phy_n.c:2270:6: warning: ‘save_regs_phy$7’ may be used uninitialized in this function drivers/net/wireless/b43/phy_n.c:2270:6: warning: ‘save_regs_phy$8’ may be used uninitialized in this function FWIW, the usage of these variables is goverened by checks that match their initializations. So, I think these are actually false warnings. Still, I would rather avoid the warning SPAM... Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 John W. Linville 提交于
CC [M] drivers/net/wireless/ath/ath5k/reset.o drivers/net/wireless/ath/ath5k/reset.c: In function ‘ath5k_hw_init_core_clock’: drivers/net/wireless/ath/ath5k/reset.c:100:51: warning: ‘txf2txs’ may be used uninitialized in this function Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 29 4月, 2011 12 次提交
-
-
由 Amitkumar Karwar 提交于
Since timestamp in beacon buffer keeps changing all the time, the memcmp check in mwifiex_save_curr_bcn() is redundant. Remove that memcmp check and also avoid freeing and allocation of buffer if required beacon buffer size is same as previous one. Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Amitkumar Karwar 提交于
1) Initialise HT capabilities in cfg80211 properly. 2) Cfg80211 stack may modify "sband->ht_cap" to disable 40Mhz operation in 2.4GHz band (after recent patch "cfg80211: module_param to disable HT40 in 2.4GHz band") Therefore read "sband->ht_cap" instead of an adapter variable "hw_dot_11n_dev_cap" to get HT capabilities. Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Amitkumar Karwar 提交于
There are some SD8787 cards which don't support 5GHz band. Therefore initialise 5GHz band parameters only if hardware supports the band. Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 John W. Linville 提交于
AFAICT, this driver is claiming that 24 bits of rate info fit into a 16-bit field in the Tx descriptor. Anyway, the use of bitfields is frowned-upon for a variety of well-documented reasons... Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
This callback is used to set the minimum rate for management frames. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
This patch adds WMI_BITRATE_MASK_CMDID which can be used by the set_bitrate_mask() handler. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
Bump the firmware version to 1.2 Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Randy Dunlap 提交于
Convert all libertas/ files to use kernel-doc notation instead of whatever it was (doxygen?). Add or fix function parameters in several places. Use expected style for multi-line comments in lots of places. Remove erroneous /** in multiple places. Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com> Acked-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Arik Nemtsov 提交于
In AP mode we register for the MAX_TX_RETRY and INACTIVE_STA events. Both are reported to the upper layers as a TX failure in the offending stations. In STA mode we register only for the MAX_TX_RETRY event. A TX failure is interpreted as a loss of connection. Support for IEEE80211_HW_REPORTS_TX_ACK_STATUS has been removed to avoid the inherent race condition of a mac80211 TX failure counter in addition to the FW counter. This patch depends on "mac80211: allow low level driver to report packet loss" Signed-off-by: NArik Nemtsov <arik@wizery.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Vivek Natarajan 提交于
Use ps wrappers before accessing hw registers in btcoex. Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Vivek Natarajan 提交于
Generic timer interrupt was not triggered unless autosleep was disabled. Since autosleep is enabled in the newer chipsets, enable generic timer for using with bt coex logic. Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-