Add COMPILE_TEST for the compilation test coverage.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Until we have proper support to make I2C slave support fully optional,
select it to prevent build errors on randconfigs.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Sigma Designs chips use a variant of this controller with the following
differences:

- The BUSY bit in the STATUS register is inverted
- Bit 8 of the CONFIG register must be set
- The controller can generate interrupts

This patch adds support for the first two of these.  It also calculates
and sets the correct clock divisor if a clk is provided.  The bus
frequency is optionally speficied in the device tree node.
Signed-off-by: NMans Rullgard <mans@mansr.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Allow the eg20t I2C driver to be built for MIPS platforms, in
preparation for use on the MIPS Boston board.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Adding Intel codename Lewisburg platform device IDs for SMBus.
Signed-off-by: NAlexandra Yates <alexandra.yates@linux.intel.com>
Reviewed-by: NJean Delvare <jdelvare@suse.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This IP is available on Xilinx ZynqMP.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add missing entries into i2c-i801 documentation and Kconfig about recently
added Intel DNV and Broxton.
Reported-by: NJean Delvare <jdelvare@suse.de>
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: NJean Delvare <jdelvare@suse.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add support for on-chip I2C controller used on newer UniPhier SoCs
such as PH1-Pro4, PH1-Pro5, etc.  This adapter is equipped with
8-depth TX/RX FIFOs.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add support for on-chip I2C controller used on old UniPhier SoCs
such as PH1-LD4, PH1-sLD8, etc.  This adapter is so simple that
it has no FIFO in it.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: NHou Zhiqiang <B48286@freescale.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The ChromeOS EC tunnel I2C bus driver depend on CROS_EC_PROTO but
MFD_CROS_EC select CROS_EC_PROTO instead. Mixing select and depends
on is bad practice as it may lead to circular Kconfig dependencies.

Since the platform device that is matched with the I2C bus driver
is registered by the ChromeOS EC mfd driver, I2C_CROS_EC_TUNNEL
really depends on MFD_CROS_EC. And because this config option
selects CROS_EC_PROTO, that dependency is met as well. So make the
driver to depend on MFD_CROS_EC instead of CROS_EC_PROTO.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add support for the I2C controller found on several NXP devices
including LPC2xxx, LPC178x/7x and LPC18xx/43xx. The controller
is implemented as a state machine and the driver act upon the
state changes when the bus is accessed.

The I2C controller supports master/slave operation, bus
arbitration, programmable clock rate, and speeds up to 1 Mbit/s.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add a basic driver for the Renesas EMEV2 SoC. Based on the driver from
the BSP which was first worked on by Ian, and made ready for upstream by
me.
Signed-off-by: NIan Molton <ian.molton@codethink.co.uk>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

If NO_DMA=y:

    ERROR: "dma_unmap_single" [drivers/i2c/busses/i2c-mt65xx.ko] undefined!
    ERROR: "dma_mapping_error" [drivers/i2c/busses/i2c-mt65xx.ko] undefined!
    ERROR: "dma_map_single" [drivers/i2c/busses/i2c-mt65xx.ko] undefined!

Add a dependency on HAS_DMA to fix this.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The MFD driver should only have the logic to instantiate its child devices
and setup any shared resources that will be used by the subdevices drivers.

The cros_ec MFD is more complex than expected since it also has helpers to
communicate with the EC. So the driver will only get more bigger as other
protocols are supported in the future. So move the communication protocol
helpers to its own driver as drivers/platform/chrome/cros_ec_proto.c.
Suggested-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: NHeiko Stuebner <heiko@sntech.de>
Acked-by: NLee Jones <lee.jones@linaro.org>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Adding support for i2c controller driver for Broadcom settop
SoCs.
Signed-off-by: NKamal Dasu <kdasu.kdev@gmail.com>
[wsa: removed superfluous owner in platform_driver]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The mediatek SoCs have I2C controller that handle I2C transfer.
This patch include common I2C bus driver.
This driver is compatible with I2C controller on mt65xx/mt81xx.
Signed-off-by: NXudong Chen <xudong.chen@mediatek.com>
Signed-off-by: NLiguo Zhang <liguo.zhang@mediatek.com>
Signed-off-by: NEddie Huang <eddie.huang@mediatek.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add SLIMpro I2C device driver on APM X-Gene platform. This I2C
device driver use the SLIMpro Mailbox driver to tunnel message to
the SLIMpro coprocessor to do the work of accessing I2C components.
Signed-off-by: NFeng Kan <fkan@apm.com>
Signed-off-by: NHieu Le <hnle@apm.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.

Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add an I2C bus driver i2c-xlp9xx.c to support the I2C block in the
XLP9xx/XLP5xx MIPS SoC. Update Kconfig and Makefile to add the
CONFIG_I2C_XLP9XX option.
Signed-off-by: NSubhendu Sekhar Behera <sbehera@broadcom.com>
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Reviewed-by: NRay Jui <rjui@broadcom.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Adds the i2c bus controller driver for the Ingenic JZ4780 SoC.
Signed-off-by: NZubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The CX92755 is an SoC in the Conexant Digicolor series. The devicetree binding
document describes the I2C controller on the CX92755 SoC, that is also shared
by some other SoCs in the Digicolor series. The driver adds support.
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
[wsa: fixed spaces around operators]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

IOSF_MBI is tristate. Baytrail driver isn't.
Reported-by: NRandy Dunlap <rdunlap@infradead.org>
Acked-by: NDavid E. Box <david.e.box@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add initial support to the Broadcom iProc I2C controller found in the
iProc family of SoCs.

The iProc I2C controller has separate internal TX and RX FIFOs, each has
a size of 64 bytes. The iProc I2C controller supports two bus speeds
including standard mode (100kHz) and fast mode (400kHz)
Signed-off-by: NRay Jui <rjui@broadcom.com>
Reviewed-by: NScott Branden <sbranden@broadcom.com>
Reviewed-by: NKevin Cernekee <cernekee@chromium.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Commit 9439eb3a ("asm-generic: io: implement relaxed
accessor macros as conditional wrappers") has added
{read,write}{b,w,l,q}_relaxed to include/asm-generic/io.h.
So COMPILE_TEST can be added.
Signed-off-by: NZhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Make the slave support depend on CONFIG_I2C_SLAVE. Otherwise it gets
included unconditionally, even when it is not needed.

I2C bus drivers which implement slave support must select
I2C_SLAVE.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

IOSF_MBI depends on PCI, so we should not select it but depend on it.
This ensures also we compile on X86 only, other archs will break because
of an arch specific include. Also depend on ACPI since this driver uses
it.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Acked-by: NDavid E. Box <david.e.box@linux.intel.com>

This patch implements an I2C bus sharing mechanism between the host and platform
hardware on select Intel BayTrail SoC platforms using the X-Powers AXP288 PMIC.

On these platforms access to the PMIC must be shared with platform hardware. The
hardware unit assumes full control of the I2C bus and the host must request
access through a special semaphore. Hardware control of the bus also makes it
necessary to disable runtime pm to avoid interfering with hardware transactions.
Signed-off-by: NDavid E. Box <david.e.box@linux.intel.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

If NO_DMA=y:

drivers/built-in.o: In function `sh_mobile_i2c_dma_unmap':
i2c-sh_mobile.c:(.text+0x60de42): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sh_mobile_i2c_xfer_dma':
i2c-sh_mobile.c:(.text+0x60df22): undefined reference to `dma_map_single'
i2c-sh_mobile.c:(.text+0x60df2e): undefined reference to `dma_mapping_error'
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The patch exposes the available i2c busses on the PowerNV platform
to the kernel and implements the bus driver to support i2c and
smbus commands.
The driver uses the platform device infrastructure to probe the busses
on the platform and registers them with the i2c driver framework.
Signed-off-by: NNeelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de> (I2C part, excluding the bindings)
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Now that we are using the clk notifier framework we get compile errors
without COMMON_CLK. But the driver fails to probe without COMMON_CLK
anyways, so just add that as a Kconfig dependency.
Signed-off-by: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The SCB is present on IMG SoCs other than the META-based TZ1090,
such as the MIPS-based Pistachio SoC.  Relax the Kconfig dependency
so that it can be built on any MIPS or META machine.
Signed-off-by: NAndrew Bresticker <abrestic@chromium.org>
Acked-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This is a driver for the I2C controller found in Amlogic Meson SoCs.
Signed-off-by: NBeniamino Galvani <b.galvani@gmail.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add support for the IMG I2C Serial Control Bus (SCB) found on the
Pistachio and TZ1090 SoCs.
Reviewed-by: NAndrew Bresticker <abrestic@chromium.org>
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
[Ezequiel: code cleaning and rebasing]
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Signed-off-by: NDevin Ryles <devin.ryles@intel.com>
Reviewed-by: NJean Delvare <jdelvare@suse.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This patch adds support for the Diolan DLN-2 I2C master module. Due
to hardware limitations it does not support SMBUS quick commands.

Information about the USB protocol interface can be found in the
Programmer's Reference Manual [1], see section 6.2.2 for the I2C
master module commands and responses.

[1] https://www.diolan.com/downloads/dln-api-manual.pdfSigned-off-by: NLaurentiu Palcu <laurentiu.palcu@intel.com>
Signed-off-by: NOctavian Purdila <octavian.purdila@intel.com>
Acked-by: NWolfram Sang <wsa@the-dreams.de>
Reviewed-by: NJohan Hovold <johan@kernel.org>
[Lee: Fixed some whitespace issues in Kconfig]
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch adds the I2C/SMBus Device IDs for the Intel Sunrise Point PCH.
Signed-off-by: NJames Ralston <james.d.ralston@intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

I2C drivers for hix5hd2 soc series, including following chipset
Hi3716CV200, Hi3719CV100, Hi3718CV100, Hi3719MV100, Hi3718MV100.
Signed-off-by: NWei Yan <sledge.yanwei@huawei.com>
Signed-off-by: NZhangfei Gao <zhangfei.gao@linaro.org>
[wsa: folded dt docs into this patch]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add support for AMD version of the DW I2C host controller. The device is
enumerated from ACPI namespace with ACPI ID AMD0010. Because the core
driver needs an input source clock, and this is not an Intel LPSS device
where clocks are provided through drivers/acpi/acpi_lpss.c, we register the
clock ourselves if the clock rate is given in ->driver_data
Signed-off-by: NCarl Peng <carlpeng008@gmail.com>
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add I2C bus driver for the controller found in the LSI Axxia family SoCs. The
driver implements 10-bit addressing and SMBus transfer modes via emulation
(including SMBus block data read).
Signed-off-by: NAnders Berg <anders.berg@avagotech.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>