Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

When adding a new hard interface (e.g. wlan0) to a soft interface (e.g. bat0)
and the former is already enslaved in another virtual interface (e.g. a software
bridge) batman-adv has to free it first and then continue with the adding
mechanism.

In this way the behaviour becomes consistent with what "ip link set master"
does. At the moment batman-adv enslaves the hard interface without checking for
the master device, possibly causing strange behaviours which are never wanted by
the users.
Reported-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

The sysfs configuration interface of batman-adv to add/remove slaves of an
soft-iface is not deadlock free and doesn't follow the currently common way to
modify slaves of an interface.

An additional configuration interface though rtnl_link is introduced which
provides easy device adding/removing with tools like "ip":
$ ip link set dev eth0 master bat0
$ ip link set dev eth0 nomaster
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Acked-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

The sysfs configuration interface of batman-adv to add/remove soft-interfaces
is not deadlock free and doesn't follow the currently common way to create new
virtual interfaces.

An additional interface though rtnl_link is introduced which provides easy device
creation/deletion with tools like "ip":

$ ip link add dev bat0 type batadv
$ ip link del dev bat0
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
CC: Sven Eckelmann <sven@narfation.org>
Acked-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

batman-adv has an unusual way to manage softinterfaces. These will be created
automatically when a user writes to the batman-adv/mesh_iface file in sysfs and
removed when no slave device exists anymore.

This behaviour cannot be changed without breaking compatibility with existing
code. Instead other interfaces should be able to slightly reduce this behaviour
and provide a more common reaction to a removal of a slave interface.
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Acked-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

The deinitialization of the soft-interface created in ndo_init/constructor
should be done in the destructor and not directly before calling
unregister_netdevice
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Acked-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

The initialization of an net_device object should be done in the
init/constructor function and not from the outside after the register_netdevice
was done to avoid race conditions.
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Acked-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

Add a htonl() in network_coding.c when reading the sequence number
from received ogm_packet, to avoid wrong byte ordering when comparing
with a host value. This bug was introduced in
3ed7ada3f0bbcd058567bc0a8f9729a73eba7db6 ("batman-adv: network coding -
detect coding nodes and remove these after timeout").

Change the type of coded_packet->coded_len from uint16 to __be16 to
avoid wrong assumptions about endianness in later uses. Introduced in
c3289f3650d34b60296000a629c99f2488f7c3dd ("batman-adv: network coding -
code and transmit packets if possible").
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NMartin Hundebøll <martin@hundeboll.net>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

Signed-off-by: NTony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This formatting issue was introduced with commit
d4ac3236Signed-off-by: NTony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch lets dgram_recvmsg fill in the sockaddr struct in
msg->msg_name with the source address of the packet.
This is used by the userland functions recvmsg and recvfrom to get the
senders address.

[Stefan: Changed from old zigbee legacy tree to mainline]
Signed-off-by: NStephen Röttger <stephen.roettger@zero-entropy.de>
Signed-off-by: NStefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gso_segs were reset to zero when kernel receive packets from untrusted
source. But we use this zero value to estimate precise packet len which is
wrong. So this patch tries to estimate the correct gso_segs value before using
it in qdisc_pkt_len_init().

Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set the transport header for 1) some drivers (e.g ixgbe needs l4 header to do
atr) 2) precise packet length estimation (introduced in 1def9238) needs l4
header to compute header length.

So this patch first tries to get l4 header for packet socket through
skb_flow_dissect(), and pretend no l4 header if skb_flow_dissect() fails.

Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The previous code would just compress the UDP header and send the compressed
UDP header along with the uncompressed one.
Signed-off-by: NTony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NTony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sets the sequence number in the frame format. Without this fix, the sequence
number is always set to 0. This makes trafic analysis very hard.
Signed-off-by: NTony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bring-over mac802154_dev_get_dsn() function that was present in the
Linux ZigBee kernel. This function is called by the 6LoWPAN code in
order to properly set the DSN (Data Sequence Number) value in the IEEE
802.15.4 frame.
Signed-off-by: NTony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NTony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add pr_debug() call in order to debug 6LoWPAN fragmentation and
reassembly.
Signed-off-by: NTony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The first fragment, FRAG1, must contain some payload according to the
specs. However, as it is currently written, the first fragment will
remain empty and only contain the 6lowpan headers.

This patch also extracts the transport layer information from the first
fragment. This information is used later on when uncompressing UDP
header.

Thanks to Wolf-Bastian Pöttner for noticing that the offset value was
not properly initialized.
Signed-off-by: NTony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The IEEE 802.15.4 standard uses the 0xFFFF short address (2 bytes) for message
broadcasting.
Signed-off-by: NTony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NTony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This feature is especially important when using fragmentation, because
the reassembly mechanism cannot recover from the loss of a fragment.

Note that some hardware ignore this flag and not will not transmit
acknowledgments even if this is set.
Signed-off-by: NTony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This causes a drop of the UDP packet.
Signed-off-by: NTony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current test is not RFC6282 compliant. The same issue has been found
and fixed in Contiki. This patch is basically a port of their fix.
Signed-off-by: NTony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the legacy array rtm_min still exists, the length check within
these functions is covered by rtm_min[RTM_NEWTFILTER],
rtm_min[RTM_NEWQDISC] and rtm_min[RTM_NEWTCLASS].

But after Thomas Graf removed rtm_min several days ago, these checks
are missing. Other doit functions should be OK.
Signed-off-by: NHong Zhiguo <honkiko@gmail.com>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Inspection of upper layer protocol is considered harmful, especially
if it is about ARP or other stateful upper layer protocol; driver
cannot (and should not) have full state of them.

IPv4 over Firewire module used to inspect ARP (both in sending path
and in receiving path), and record peer's GUID, max packet size, max
speed and fifo address.  This patch removes such inspection by extending
our "hardware address" definition to include other information as well:
max packet size, max speed and fifo.  By doing this, The neighbour
module in networking subsystem can cache them.

Note: As we have started ignoring sspd and max_rec in ARP/NDP, those
      information will not be used in the driver when sending.

When a packet is being sent, the IP layer fills our pseudo header with
the extended "hardware address", including GUID and fifo.  The driver
can look-up node-id (the real but rather volatile low-level address)
by GUID, and then the module can send the packet to the wire using
parameters provided in the extendedn hardware address.

This approach is realistic because IP over IEEE1394 (RFC2734) and IPv6
over IEEE1394 (RFC3146) share same "hardware address" format
in their address resolution protocols.

Here, extended "hardware address" is defined as follows:

union fwnet_hwaddr {
	u8 u[16];
	struct {
		__be64 uniq_id;		/* EUI-64			*/
		u8 max_rec;		/* max packet size		*/
		u8 sspd;		/* max speed			*/
		__be16 fifo_hi;		/* hi 16bits of FIFO addr	*/
		__be32 fifo_lo;		/* lo 32bits of FIFO addr	*/
	} __packed uc;
};

Note that Hardware address is declared as union, so that we can map full
IP address into this, when implementing MCAP (Multicast Cannel Allocation
Protocol) for IPv6, but IP and ARP subsystem do not need to know this
format in detail.

One difference between original ARP (RFC826) and 1394 ARP (RFC2734)
is that 1394 ARP Request/Reply do not contain the target hardware address
field (aka ar$tha).  This difference is handled in the ARP subsystem.

CC: Stephan Gatzka <stephan.gatzka@gmail.com>
Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use common function get calculate rtnl_link_stats64 stats.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reuse common ip-tunneling code which is re-factored from GRE
module.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Following patch refactors GRE code into ip tunneling code and GRE
specific code. Common tunneling code is moved to ip_tunnel module.
ip_tunnel module is written as generic library which can be used
by different tunneling implementations.

ip_tunnel module contains following components:
 - packet xmit and rcv generic code. xmit flow looks like
   (gre_xmit/ipip_xmit)->ip_tunnel_xmit->ip_local_out.
 - hash table of all devices.
 - lookup for tunnel devices.
 - control plane operations like device create, destroy, ioctl, netlink
   operations code.
 - registration for tunneling modules, like gre, ipip etc.
 - define single pcpu_tstats dev->tstats.
 - struct tnl_ptk_info added to pass parsed tunnel packet parameters.

ipip.h header is renamed to ip_tunnel.h
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's always zero.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ip-header id needs to be incremented even if IP_DF flag is set.
This behaviour was changed in commit 490ab081
(IP_GRE: Fix IP-Identification).

Following patch fixes it so that identification is always
incremented.
Reported-by: NCong Wang <amwang@redhat.com>
Acked-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>

This reverts commit d6a8c36d.
Next commit makes this commit unnecessary.
Acked-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 10c0d7ed.
Next commit makes this commit unnecessary.
Acked-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we have defined a sparse port allocation which is non-contiguous and
contains gaps, the code freeing port_names will just stop when it
encouters a first NULL port_names, which is not right, we should iterate
over all possible number of ports (DSA_MAX_PORTS) until we are done.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch factors the freeing of the struct dsa_platform_data
manipulated by the driver identically in two places to a single
function.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When neither IFF_BRIDGE nor IFF_BRIDGE_PORT is set,
and afspec == NULL but  protinfo != NULL, we run into
"if (err == 0) br_ifinfo_notify(RTM_NEWLINK, p);" with
random value in ret.

Thanks to Sergei for pointing out the error in commit comments.
Signed-off-by: NHong Zhiguo <honkiko@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>