This patch introduce no functional changes.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Roman Zippel <zippel@linux-m68k.org>

With this patch we have all the Kconfig file shared
between i386 and x86_64.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>

Most of the arch settings were equal so combine them
in the first part of Kconfig.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>

No functional changes.
A prepatory step towards full unification.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>

To ease unification of Kconfig.i386 and Kconfig.x86_64
add X86_64 dependencies to all x86_64 specific symbols.

This patch introduce no functional changes but is one step
towards unification. This smaller step is used to ease
review of the patch set.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>

To ease unification of Kconfig.i386 and Kconfig.x86_64
add X86_32 dependencies to all i386 specific symbols.

This patch introduce no functional changes but is one step
towards unification. This smaller step is used to ease
review of the patch set.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>

Move all CPU definitions to Kconfig.cpu
Always define X86_MINIMUM_CPU_FAMILY and do the
obvious code cleanup in boot/cpucheck.c

Comments from: Adrian Bunk <bunk@kernel.org> incorporated.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Adrian Bunk <bunk@kernel.org>
Cc: Brian Gerst <bgerst@didntduck.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>

This step introduces the file arch/x86/Kconfig
which contains all the menu's from "Power Management"
and below.

The main part of the new Kconfig file is shared
and the remaining i386/x86_64 specific symbols
are covered by dependencies.

A x86_64 allmodconfig build did not show any differences.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>

Merge the two Kconfig files to a single file.

Checked using make allmodconfig for x86_64.
No changes in build.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Adrian Bunk <bunk@kernel.org>
Cc: Dave Jones <davej@codemonkey.org.uk>

Add documentation in Kconfig help about the move of /proc/acpi/battery
to /sys/class/power_supply when selecting ACPI_PROCFS.  This will impact
a lot of users and should be documented.
Signed-off-by: NJerome Pinot <ngc891@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
  Add missing "\n" to log message

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: Don't fail device revalidation for bad _GTF methods
  libata: port and host should be stopped before hardware resources are released
  libata: skip 0xff polling for PATA controllers
  libata: pata_platform: Support polling-mode configuration.
  libata: Support PIO polling-only hosts.
  libata sata_qstor conversion to new error handling (EH).
  libata sata_qstor workaround for spurious interrupts
  libata sata_qstor nuke idle state
  nv_hardreset: update dangling reference to bugzilla entry
  ata_piix: add SATELLITE PRO U200 to broken suspend list

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (40 commits)
  r8169: prevent bit sign expansion error in mdio_write
  r8169: revert 7da97ec9 (bis repetita)
  sky2: new pci id's
  ax88796: add superh to kconfig dependencies
  qla3xxx: bugfix: Fix bad logical operation in link state machine.
  qla3xxx: bugfix: Move link state machine into a worker thread
  pasemi_mac: Fix CRC checks
  pasemi_mac: Don't set replace-source-address descriptor bits
  bonding: don't validate address at device open
  bonding: fix rtnl locking merge error
  sky2: netpoll on port 0 only
  b43: Fix kconfig dependencies for rfkill and leds
  b43legacy: Fix sparse warning
  b43: properly request pcmcia IRQ
  b43legacy: fix shared IRQ race condition
  b43: fix shared IRQ race condition
  b43legacy: add me as maintainer and fix URLs
  b43legacy: fix possible buffer overrun in debugfs
  b43: Rewrite and fix rfkill init
  b43: debugfs SHM read buffer overrun fix
  ...

This reverts commit f33bac8d, which was
totally bogus.

The arm/configs/netx_defconfig file already existed - in the right
place. Namely under "arch".
Noticed-by: NPaul Mundt <lethal@linux-sh.org>
Acked-by: NRobert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NRolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Oops.

The current code does not like being given an u16 with the highest
bit set as an argument to mdio_write. Let's enforce a correct range of
values for both the register address and value (resp. 5 and 16 bits).

The callers are currently left as-is.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>

RTL_GIGA_MAC_VER_17 breaks as well.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>

Found a couple of more chips in the latest version of the vendor driver.
They are minor variations on existing chips.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ax88796: add superh to kconfig dependencies

This patch adds sh architecture support to the ax88796 kconfig.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Luckily, this wasn't reported or reproduced. The logical operation for
setting duplex had wrong grouping.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The link state machine requires access to some resources that
are shared with the iSCSI function on the chip.  (See iSCSI
driver at drivers/scsi/qla4xxx)  If the interface is being
up/downed at a rapid pace this driver may need to sleep
waiting to get access to the common resources. For this we
are moving the state machine to run as a work thread.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make sure we don't feed packets with bad CRC up the network stack,
and discount the packet length as reported from the MAC for the CRC
field.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Don't use the "replace source address with local MAC address" bits, since
it causes problems on some variations of the hardware due to an erratum.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The standard validate_addr handler refuses to accept the all zeroes address
as valid.  However, it's common historical practice for the bonding
master to be configured up prior to having any slaves, at which time the
master will have a MAC address of all zeroes.

Resolved by setting the dev->validate_addr to NULL.  The master still can't
end up with an invalid address, as the set_mac_address function tests
for validity.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

	Looks like I incorrectly merged one of the rtnl lock changes,
so that one function, bonding_show_active_slave, held rtnl but didn't
release it, and another, bonding_store_active_slave, never held rtnl but
did release it.

	Fixed so the first function doesn't mess with rtnl, and the
second correctly acquires and releases rtnl.

	Bug reported by Moni Shoua <monis@voltaire.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Netpoll will only work on port 0 because of the restrictive
relationship between NAPI and netpoll.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix dependencies for built-in b43.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix a sparse warning about a nonstatic function.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

PCMCIA needs an additional step to request the IRQ.

No need to add code to release the IRQ here, as that's done
automatically in pcmcia_disable_device().
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix an IRQ race condition in b43legacy. If we call
b43legacy_wireless_core_stop(), it will set the status of the device to
INITIALIZED and the IRQ handler won't care any longer about IRQs, thus the
kernel will disable the IRQ if it's shared (unless we boot it with the
'irqpoll' option). So we must disable IRQs before changing the device
status.
Signed-off-by: NStefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix an IRQ race condition in b43. If we call b43_stop_wireless_core(), it
will set the status of the device to INITIALIZED and the IRQ handler won't
care any longer about IRQs, thus the kernel will disable the IRQ if it's
shared (unless we boot it with the 'irqpoll' option). So we must disable
IRQs before changing the device status.
Signed-off-by: NStefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As b43legacy is going to be orphaned, add me as a maintainer. Fix URLs for
the related website and fix my e-mail address in MAINTAINERS file.
Signed-off-by: NStefano Brivio <stefano.brivio@polimi.it>
Cc: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix possible buffer overrun.

The patch to b43 by Michael Buesch <mb@bu3sch.de> has been ported to
b43legacy.
Signed-off-by: NStefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The rfkill subsystem doesn't like code like that
rfkill_allocate();
rfkill_register();
rfkill_unregister();
rfkill_register(); /* <- This will crash */

This sequence happens with
modprobe b43
ifconfig wlanX up
ifconfig wlanX down
ifconfig wlanX up

Fix this by always re-allocating the rfkill stuff before register.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix possible buffer overrun.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

wl->mutex might already be locked on initialization.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix the initialization for PCMCIA devices.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If i reaches zero, the loop ends, but the postfix decrement subtracts it to -1.
Testing for 'i == 0', later in the function, will not fulfill its purpose.
Signed-off-by: NRoel Kluin <12o3l@tiscali.nl>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix section mismatch warning:

WARNING: vmlinux.o(.data+0x36fcc): Section mismatch: reference to .init.data:prism2_pci_id_table (between 'prism2_pci_drv_id' and 'prism2_pci_funcs')
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2x00 is broken when it comes down to adhoc and master mode.
The main problem is the beaconing, which is completely failing.
Untill a solution has been found, both beacon requiring modes
must be disabled to prevent numerous bug reports.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>