Sometimes, the users may require a quirk to be provided from ACPI subsystem
core to prevent a GPE from flooding.
Normally, if a GPE cannot be dispatched, ACPICA core automatically prevents
the GPE from firing. But there are cases the GPE is dispatched by _Lxx/_Exx
provided via AML table, and OSPM is lacking of the knowledge to get
_Lxx/_Exx correctly executed to handle the GPE, thus the GPE flooding may
still occur.

The existing quirk mechanism can be enabled/disabled using the following
commands to prevent such kind of GPE flooding during runtime:
 # echo mask > /sys/firmware/acpi/interrupts/gpe00
 # echo unmask > /sys/firmware/acpi/interrupts/gpe00
To avoid GPE flooding during boot, we need a boot stage mechanism.

This patch provides such a boot stage quirk mechanism to stop this kind of
GPE flooding. This patch doesn't fix any feature gap but since the new
feature gaps could be found in the future endlessly, and can disappear if
the feature gaps are filled, providing a boot parameter rather than a DMI
table should suffice.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=53071
Link: https://bugzilla.kernel.org/show_bug.cgi?id=117481
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/887793Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Starting from Intel Skylake the iTCO watchdog timer registers were moved to
reside in the same register space with SMBus host controller.  Not all
needed registers are available though and we need to unhide P2SB (Primary
to Sideband) device briefly to be able to read status of required NO_REBOOT
bit. The i2c-i801.c SMBus driver used to handle this and creation of the
iTCO watchdog platform device.

Windows, on the other hand, does not use the iTCO watchdog hardware
directly even if it is available. Instead it relies on ACPI Watchdog Action
Table (WDAT) table to describe the watchdog hardware to the OS. This table
contains necessary information about the the hardware and also set of
actions which are executed by a driver as needed.

This patch implements a new watchdog driver that takes advantage of the
ACPI WDAT table. We split the functionality into two parts: first part
enumerates the WDAT table and if found, populates resources and creates
platform device for the actual driver. The second part is the driver
itself.

The reason for the split is that this way we can make the driver itself to
be a module and loaded automatically if the WDAT table is found. Otherwise
the module is not loaded.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

It is possible to register _Qxx from namespace and use the ECDT EC to
perform event handling. The reported bug reveals that Windows is using ECDT
in this way in case the namespace EC is not present. This patch facilitates
Linux to support ECDT in this way.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=115021Reported-and-tested-by: NLuya Tshimbalanga <luya@fedoraproject.org>
Tested-by: NJonh Henderson <jw.hendy@gmail.com>
Reviewed-by: NPeter Wu <peter@lekensteyn.nl>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This patch makes 2 changes:

1. Restore old behavior
Originally, EC driver stops handling both events and transactions in
acpi_ec_block_transactions(), and restarts to handle transactions in
acpi_ec_unblock_transactions_early(), restarts to handle both events and
transactions in acpi_ec_unblock_transactions().
While currently, EC driver still stops handling both events and
transactions in acpi_ec_block_transactions(), but restarts to handle both
events and transactions in acpi_ec_unblock_transactions_early().
This patch tries to restore the old behavior by dropping
__acpi_ec_enable_event() from acpi_unblock_transactions_early().

2. Improve old behavior
However this still cannot fix the real issue as both of the
acpi_ec_unblock_xxx() functions are invoked in the noirq stage. Since the
EC driver actually doesn't implement the event handling in the polling
mode, re-enabling the event handling too early in the noirq stage could
result in the problem that if there is no triggering source causing
advance_transaction() to be invoked, pending SCI_EVT cannot be detected by
the EC driver and _Qxx cannot be triggered.
It actually makes sense to restart the event handling in any point during
resuming after the noirq stage. Just like the boot stage where the event
handling is enabled in .add(), this patch further moves
acpi_ec_enable_event() to .resume(). After doing that, the following 2
functions can be combined:
acpi_ec_unblock_transactions_early()/acpi_ec_unblock_transactions().

The differences of the event handling availability between the old behavior
(this patch isn't applied) and the new behavior (this patch is applied) are
as follows:
                        !Applied        Applied
before suspend          Y               Y
suspend before EC       Y               Y
suspend after EC        Y               Y
suspend_late            Y               Y
suspend_noirq           Y (actually N)  Y (actually N)
resume_noirq            Y (actually N)  Y (actually N)
resume_late             Y (actually N)  Y (actually N)
resume before EC        Y (actually N)  Y (actually N)
resume after EC         Y (actually N)  Y
after resume            Y (actually N)  Y
Where "actually N" means if there is no triggering source, the EC driver
is actually not able to notice the pending SCI_EVT occurred in the noirq
stage. So we can clearly see that this patch has improved the situation.
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Tested-by: NTodd E Brandt <todd.e.brandt@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Following the fwnode of a device is currently a one-way road: We provide
ACPI_COMPANION() to obtain the fwnode but there's no (public) method to
do the reverse. Granted, there may be multiple physical_nodes, but often
the first one in the list is sufficient.

A handy function to obtain it was introduced with commit 3b95bd16
("ACPI: introduce a function to find the first physical device"), but
currently it's only available internally.

We're about to add an EFI Device Path parser which needs this function.
Consider the following device path: ACPI(PNP0A03,0)/PCI(28,2)/PCI(0,0)
The PCI root is encoded as an ACPI device in the path, so the parser
has to find the corresponding ACPI device, then find its physical node,
find the PCI bridge in slot 1c (decimal 28), function 2 below it and
finally find the PCI device in slot 0, function 0.

To this end, make acpi_get_first_physical_node() public.
Signed-off-by: NLukas Wunner <lukas@wunner.de>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Change the argument of acpi_ioapic_add() to a generic ACPI handle, and
move its prototype from drivers/acpi/internal.h to include/linux/acpi.h
so that it can be called from outside the pci_root driver.
Signed-off-by: NRui Wang <rui.y.wang@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bhelgaas@google.com
Cc: helgaas@kernel.org
Cc: linux-acpi@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: rjw@rjwysocki.net
Cc: tony.luck@intel.com
Link: http://lkml.kernel.org/r/1471420837-31003-2-git-send-email-rui.y.wang@intel.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

It is reported that on some platforms, resume speed is not fast. The cause
is: in noirq stage, EC driver is working in polling mode, and each state
machine advancement requires a context switch.

The context switch is not necessary to the EC driver's polling mode. This
patch implements PM hooks to automatically switch the driver to/from the
busy polling mode to eliminate the overhead caused by the context switch.

This finally contributes to the tuning result: acpi_pm_finish() execution
time is improved from 192ms to 6ms.
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Reported-and-tested-by: NTodd E Brandt <todd.e.brandt@linux.intel.com>
[ rjw: Subject ]
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Add support for ACPI reconfiguration notifiers to allow subsystems
to react to changes in the ACPI tables that happen after the initial
enumeration. This is similar with the way dynamic device tree
notifications work.

The reconfigure notifications supported for now are device add and
device remove.

Since ACPICA allows only one table notification handler, this patch
makes the table notifier function generic and moves it out of the
sysfs specific code.
Signed-off-by: NOctavian Purdila <octavian.purdila@intel.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

According to the Windows probing result, during the table loading, the EC
device described in the ECDT should be used. And the ECDT EC is also
effective during the period the namespace objects are initialized (we can
see a separate process executing _STA/_INI on Windows before executing
other device specific control methods, for example, EC._REG). During the
device enumration, the EC device described in the DSDT should be used. But
there are differences between Linux and Windows around the device probing
order. Thus in Linux, we should enable the DSDT EC as early as possible
before enumerating devices in order not to trigger issues related to the
device enumeration order differences.

This patch thus converts acpi_boot_ec_enable() into acpi_ec_dsdt_probe() to
fix the gap. This also fixes a user reported regression triggered after we
switched the "table loading"/"ECDT support" to be ACPI spec 2.0 compliant.

Fixes: 59f0aa94 (ACPI 2.0 / ECDT: Remove early namespace reference from EC)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=119261Reported-and-tested-by: NGabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

_OSI handling code grows giant and it's time to move them into one file.

This patch collects all _OSI handling code into one single file.
So that we only have the following functions to be used externally:

 early_acpi_osi_init(): Used by DMI detections;
 acpi_osi_init(): Used to initialize OSI command line settings and install
                  Linux specific _OSI handler;
 acpi_osi_setup(): The API that should be used by the external quirks.
 acpi_osi_is_win8(): The API is used by the external drivers to determine
                     if BIOS supports Win8.

CONFIG_DMI is not useful as stub dmi_check_system() can make everything
stub because of strip.

No functional changes.
Tested-by: NLukas Wunner <lukas@wunner.de>
Tested-by: NChen Yu <yu.c.chen@intel.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This patch moves acpi_os_table_override() and
acpi_os_physical_table_override() to tables.c.

Along with the mechanisms, acpi_initrd_initialize_tables() is also moved to
tables.c to form a static function. The following functions are renamed
according to this change:
 1. acpi_initrd_override() -> renamed to early_acpi_table_init(), which
    invokes acpi_table_initrd_init()
 2. acpi_os_physical_table_override() -> which invokes
    acpi_table_initrd_override()
 3. acpi_initialize_initrd_tables() -> renamed to acpi_table_initrd_scan()
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

There are several reports of freeze on enabling HWP (Hardware PStates)
feature on Skylake-based systems by the Intel P-states driver. The root
cause is identified as the HWP interrupts causing BIOS code to freeze.

HWP interrupts use the thermal LVT which can be handled by Linux
natively, but on the affected Skylake-based systems SMM will respond
to it by default.  This is a problem for several reasons:
 - On the affected systems the SMM thermal LVT handler is broken (it
   will crash when invoked) and a BIOS update is necessary to fix it.
 - With thermal interrupt handled in SMM we lose all of the reporting
   features of the arch/x86/kernel/cpu/mcheck/therm_throt driver.
 - Some thermal drivers like x86-package-temp depend on the thermal
   threshold interrupts signaled via the thermal LVT.
 - The HWP interrupts are useful for debugging and tuning
   performance (if the kernel can handle them).
The native handling of thermal interrupts needs to be enabled
because of that.

This requires some way to tell SMM that the OS can handle thermal
interrupts.  That can be done by using _OSC/_PDC in processor
scope very early during ACPI initialization.

The meaning of _OSC/_PDC bit 12 in processor scope is whether or
not the OS supports native handling of interrupts for Collaborative
Processor Performance Control (CPPC) notifications.  Since on
HWP-capable systems CPPC is a firmware interface to HWP, setting
this bit effectively tells the firmware that the OS will handle
thermal interrupts natively going forward.

For details on _OSC/_PDC refer to:
http://www.intel.com/content/www/us/en/standards/processor-vendor-specific-acpi-specification.html

To implement the _OSC/_PDC handshake as described, introduce a new
function, acpi_early_processor_osc(), that walks the ACPI
namespace looking for ACPI processor objects and invokes _OSC for
them with bit 12 in the capabilities buffer set and terminates the
namespace walk on the first success.

Also modify intel_thermal_interrupt() to clear HWP status bits in
the HWP_STATUS MSR to acknowledge HWP interrupts (which prevents
them from firing continuously).
Signed-off-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Subject & changelog, function rename ]
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This patch adds support to install tables from initrd.

If a table in the initrd wasn't used by the override mechanism,
the table would be installed after initializing all RSDT/XSDT
tables.

Link: https://lkml.org/lkml/2014/2/28/368Reported-by: NThomas Renninger <trenn@suse.de>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

On ARM64 some devices use the AMBA device and not the platform bus for
probing so add support for this. Uses a dummy clock for apb_pclk as ACPI
does not have a suitable clock representation and to keep the core
AMBA bus code unchanged between probing methods.
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NGraeme Gregory <graeme.gregory@linaro.org>
Signed-off-by: NAleksey Makarov <aleksey.makarov@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Factor out the code that finds the first physical device
of a given ACPI device.  It is used in several places.
Signed-off-by: NAleksey Makarov <aleksey.makarov@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Add a missing space in the definition of struct acpi_device_bus_id.
Signed-off-by: NLukas Wunner <lukas@wunner.de>
[ rjw: Subject and changelog ]
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

There's an idiom in use by 7 Linux drivers to detect the presence of a
particular ACPI HID by walking the namespace with acpi_get_devices().
The callback passed to acpi_get_devices() is mostly identical across
the drivers, leading to lots of duplicate code.

Add acpi_dev_present(), the ACPI equivalent to pci_dev_present(),
allowing us to deduplicate all that boilerplate in the drivers.
Signed-off-by: NLukas Wunner <lukas@wunner.de>
Reviewed-by: NHanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Its a bit odd that debugfs_create_bool() takes 'u32 *' as an argument,
when all it needs is a boolean pointer.

It would be better to update this API to make it accept 'bool *'
instead, as that will make it more consistent and often more convenient.
Over that bool takes just a byte.

That required updates to all user sites as well, in the same commit
updating the API. regmap core was also using
debugfs_{read|write}_file_bool(), directly and variable types were
updated for that to be bool as well.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NMark Brown <broonie@kernel.org>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

global_lock is defined as an unsigned long and accessing only its lower
32 bits from sysfs is incorrect, as we need to consider other 32 bits
for big endian 64-bit systems. There are no such platforms yet, but the
code needs to be robust for such a case.

Fix that by changing type of 'global_lock' to u32.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch changes the type of the return value of the acpi_sleep_proc_init()
method to be void, as this method never fails and its return value is never
used.

Signed-off-by: Rami Rosen <ramirose@gmail.com>\
[ rjw : Fixed up the static inline stub ]
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This patch changes the type of the return value of the init_acpi_device_notify()
method to be void, as this method never fails and its return value is never
used.
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

acpi_debugfs_init function is declared with return type int in
drivers/acpi/internal.h when CONFIG_DEBUG_FS is enabled, but its
definition in drivers/acpi/debugfs.c has return type void. This is due
to commit aecad432 ("ACPI: Cleanup custom_method debug stuff"),
which changed the return type from int to void without updating the
declaration.

Fix this inconsistency by updating acpi_debugfs_init prototype.  While
at it, include internal.h in debugfs.c so that the compiler can check
that the declaration and definition remain compatible.
Signed-off-by: NNicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Some devices, like MFD subdevices, share a single ACPI companion device so
that they are able to access their resources and children. However,
currently all these subdevices are attached to the ACPI power domain and
this might cause that the power methods for the companion device get called
more than once.

In order to solve this we attach the ACPI power domain only to the first
physical device that is bound to the ACPI companion device. In case of MFD
devices, this is the parent MFD device itself.
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

To reduce the size of scan.c and improve the readability of it, move
all code related to device sysfs, modalias creation etc. to a new
file called device_sysfs.c.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

There is no need to carry potentially outdated Free Software Foundation
mailing address in file headers since the COPYING file includes it.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The platform firmware on some systems expects Linux to return "5" as
the supported ACPI revision which makes it expose system configuration
information in a special way.

For example, based on what ACPI exports as the supported revision,
Dell XPS 13 (2015) configures its audio device to either work in HDA
mode or in I2S mode, where the former is supposed to be used on Linux
until the latter is fully supported (in the kernel as well as in user
space).

Since ACPI 6 mandates that _REV should return "2" if ACPI 2 or later
is supported by the OS, a subsequent change will make that happen, so
make it possible to override that on systems where "5" is expected to
be returned for Linux to work correctly one them (such as the Dell
machine mentioned above).
Original-by: NDominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

acpi_osi_is_win8 needs access to acpi_gbl_osi_data which is not exported,
so move it to osl.c. Alternatively we could export acpi_gbl_osi_data but
that seems undesirable.

This allows video_detect.c to be build as a module, besides that
acpi_osi_is_win8() is something which does not really belong in
video_detect.c in the first place.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NDarren Hart <dvhart@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

During the period that a work queue is scheduled (queued up for run) but
hasn't been run, second schedule_work() could fail. This may not lead to
the loss of queries because QR_EC is always ensured to be submitted after
the work queue has been in the running state.

The event handling work queue can be changed into the loop style to allow
us to control the code in a more flexible way:
1. Makes it possible to add event=0x00 termination condition in the loop.
2. Increases the thoughput of the QR_EC transactions as the 2nd+ QR_EC
   transactions may be handled in the same work item used for the 1st QR_EC
   transaction, thus the delay caused by the 2nd+ work item scheduling can
   be eliminated.

Except the logging message changes and the throughput improvement, this
patch is just a funcitonal no-op.
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Tested-by: NGabriele Mazzotta <gabriele.mzt@gmail.com>
Tested-by: NTigran Gabrielyan <tigrangab@gmail.com>
Tested-by: NAdrien D <ghbdtn@openmailbox.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Use a #defined symbol ACPI_DT_NAMESPACE_HID instead of the PRP0001
string.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: NHanjun Guo <hanjun.guo@linaro.org>

In the polling mode, EC driver shouldn't access the EC registers too
frequently. Though this statement is concluded from the non-root caused
bugs (see links below), we've maintained the register access guarding
logics in the current EC driver. The guarding logics can be found here and
there, makes it hard to root cause real timing issues. This patch collects
the guarding logics into one single function so that all hidden logics
related to this can be seen clearly.

The current guarding related code also has several issues:
1. Per-transaction timestamp prevents inter-transaction guarding from being
   implemented in the same place. We have an inter-transaction udelay() in
   acpi_ec_transaction_unblocked(), this logic can be merged into ec_poll()
   if we can use per-device timestamp. This patch completes such merge to
   form a new ec_guard() function and collects all guarding related hidden
   logics in it.
   One hidden logic is: there is no inter-transaction guarding performed
   for non MSI quirk (wait polling mode), this patch skips
   inter-transaction guarding before wait_event_timeout() for the wait
   polling mode to reveal the hidden logic.
   The other hidden logic is: there is msleep() inter-transaction guarding
   performed when the GPE storming is observed. As after merging this
   commit:
     Commit: e1d4d90f
     Subject: ACPI / EC: Refine command storm prevention support
   EC_FLAGS_COMMAND_STORM is ensured to be cleared after invoking
   acpi_ec_transaction_unlocked(), the msleep() guard logic will never
   happen now. Since no one complains such change, this logic is likely
   added during the old times where the EC race issues are not fixed and
   the bugs are false root-caused to the timing issue. This patch simply
   removes the out-dated logic. We can restore it by stop skipping
   inter-transaction guarding for wait polling mode.
   Two different delay values are defined for msleep() and udelay() while
   they are merged in this patch to 550us.
2. time_after() causes additional delay in the polling mode (can only be
   observed in noirq suspend/resume processes where polling mode is always
   used) before advance_transaction() is invoked ("wait polling" log is
   added before wait_event_timeout()). We can see 2 wait_event_timeout()
   invocations. This is because time_after() ensures a ">" validation while
   we only need a ">=" validation here:
   [   86.739909] ACPI: Waking up from system sleep state S3
   [   86.742857] ACPI : EC: 2: Increase command
   [   86.742859] ACPI : EC: ***** Command(RD_EC) started *****
   [   86.742861] ACPI : EC: ===== TASK (0) =====
   [   86.742871] ACPI : EC: EC_SC(R) = 0x20 SCI_EVT=1 BURST=0 CMD=0 IBF=0 OBF=0
   [   86.742873] ACPI : EC: EC_SC(W) = 0x80
   [   86.742876] ACPI : EC: ***** Event started *****
   [   86.742880] ACPI : EC: ~~~~~ wait polling ~~~~~
   [   86.743972] ACPI : EC: ~~~~~ wait polling ~~~~~
   [   86.747966] ACPI : EC: ===== TASK (0) =====
   [   86.747977] ACPI : EC: EC_SC(R) = 0x20 SCI_EVT=1 BURST=0 CMD=0 IBF=0 OBF=0
   [   86.747978] ACPI : EC: EC_DATA(W) = 0x06
   [   86.747981] ACPI : EC: ~~~~~ wait polling ~~~~~
   [   86.751971] ACPI : EC: ~~~~~ wait polling ~~~~~
   [   86.755969] ACPI : EC: ===== TASK (0) =====
   [   86.755991] ACPI : EC: EC_SC(R) = 0x21 SCI_EVT=1 BURST=0 CMD=0 IBF=0 OBF=1
   [   86.755993] ACPI : EC: EC_DATA(R) = 0x03
   [   86.755994] ACPI : EC: ~~~~~ wait polling ~~~~~
   [   86.755995] ACPI : EC: ***** Command(RD_EC) stopped *****
   [   86.755996] ACPI : EC: 1: Decrease command
   This patch corrects this by using time_before() instead in ec_guard():
   [   54.283146] ACPI: Waking up from system sleep state S3
   [   54.285414] ACPI : EC: 2: Increase command
   [   54.285415] ACPI : EC: ***** Command(RD_EC) started *****
   [   54.285416] ACPI : EC: ~~~~~ wait polling ~~~~~
   [   54.285417] ACPI : EC: ===== TASK (0) =====
   [   54.285424] ACPI : EC: EC_SC(R) = 0x20 SCI_EVT=1 BURST=0 CMD=0 IBF=0 OBF=0
   [   54.285425] ACPI : EC: EC_SC(W) = 0x80
   [   54.285427] ACPI : EC: ***** Event started *****
   [   54.285429] ACPI : EC: ~~~~~ wait polling ~~~~~
   [   54.287209] ACPI : EC: ===== TASK (0) =====
   [   54.287218] ACPI : EC: EC_SC(R) = 0x20 SCI_EVT=1 BURST=0 CMD=0 IBF=0 OBF=0
   [   54.287219] ACPI : EC: EC_DATA(W) = 0x06
   [   54.287222] ACPI : EC: ~~~~~ wait polling ~~~~~
   [   54.291190] ACPI : EC: ===== TASK (0) =====
   [   54.291210] ACPI : EC: EC_SC(R) = 0x21 SCI_EVT=1 BURST=0 CMD=0 IBF=0 OBF=1
   [   54.291213] ACPI : EC: EC_DATA(R) = 0x03
   [   54.291214] ACPI : EC: ~~~~~ wait polling ~~~~~
   [   54.291215] ACPI : EC: ***** Command(RD_EC) stopped *****
   [   54.291216] ACPI : EC: 1: Decrease command

After cleaning up all guarding logics, we have one single function
ec_guard() collecting all old, non-root-caused, hidden logics. Then we can
easily tune the logics in one place to respond to the bug reports.

Except the time_before() change, all other changes do not change the
behavior of the EC driver.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=12011
Link: https://bugzilla.kernel.org/show_bug.cgi?id=20242
Link: https://bugzilla.kernel.org/show_bug.cgi?id=77431Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

ACPI 5.1 does not currently support S states for ARM64 hardware but
ACPI code will call acpi_target_system_state() and acpi_sleep_init()
for device power management, so introduce
CONFIG_ACPI_SYSTEM_POWER_STATES_SUPPORT and select it for x86 and
ia64 only to make sleep functions available, and also introduce stub
function to allow other drivers to function until S states are defined
for ARM64.

It will be no functional change for x86 and IA64.
Suggested-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NGraeme Gregory <graeme.gregory@linaro.org>
Signed-off-by: NTomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: NHanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

This patch implements the EC command flushing support.

During the grace period indicated by EC_FLAGS_STARTED and EC_FLAGS_STOPPED,
all submitted EC command transactions can be completed and new submissions
are prevented before suspending so that the EC hardware can be ensured to
be in the idle state when the system is resumed.

There is a good indicator for flush support:
All acpi_ec_submit_request() is invoked after checking driver state with
acpi_ec_started() except the first one. This means all code paths can be
flushed as fast as possible by discarding the requests occurred after the
flush operation. The reference increased for such kind of code path is
wrapped by acpi_ec_submit_flushable_request().
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Tested-by: NOrtwin Glück <odi@odi.ch>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This new feature is to interpret AMD specific ACPI device to
platform device such as I2C, UART, GPIO found on AMD CZ and
later chipsets. It based on example intel LPSS. Now, it can
support AMD I2C, UART and GPIO.
Signed-off-by: NKen Xue <Ken.Xue@amd.com>
Acked-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Enable support of IOAPIC hotplug by:
1) reintroducing ACPI based IOAPIC driver
2) enhance pci_root driver to hook hotplug events

The ACPI IOAPIC driver is always enabled if all of ACPI, PCI and IOAPIC
are enabled.
Signed-off-by: NJiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Len Brown <lenb@kernel.org>
Link: http://lkml.kernel.org/r/1414387308-27148-19-git-send-email-jiang.liu@linux.intel.comSigned-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This patch fixes 2 issues related to the draining behavior. But it doesn't
implement the draining support, it only cleans up code so that further
draining support is possible.

The draining behavior is expected by some platforms (for example, Samsung)
where SCI_EVT is set only once for a set of events and might be cleared for
the very first QR_EC command issued after SCI_EVT is set. EC firmware on
such platforms will return 0x00 to indicate "no outstanding event". Thus
after seeing an SCI_EVT indication, EC driver need to fetch events until
0x00 returned (see acpi_ec_clear()).

Issue 1 - acpi_ec_submit_query():
It's reported on Samsung laptops that SCI_EVT isn't checked when the
transactions are advanced in ec_poll(), which leads to SCI_EVT triggering
source lost:
 If no EC GPE IRQs are arrived after that, EC driver cannot detect this
 event and handle it.
See comment 244/247 for kernel bugzilla 44161.
This patch fixes this issue by moving SCI_EVT checks into
advance_transaction(). So that SCI_EVT is checked each time we are going to
handle the EC firmware indications. And this check will happen for both IRQ
context and task context.
Since after doing that, SCI_EVT is also checked after completing a
transaction, ec_check_sci() and ec_check_sci_sync() can be removed.

Issue 2 - acpi_ec_complete_query():
We expect to clear EC_FLAGS_QUERY_PENDING to allow queuing another draining
QR_EC after writing a QR_EC command and before reading the event. After
reading the event, SCI_EVT might be cleared by the firmware, thus it may
not be possible to queue such a draining QR_EC at that time.
But putting the EC_FLAGS_QUERY_PENDING clearing code after
start_transaction() is wrong as there are chances that after
start_transaction(), QR_EC can fail to be sent. If this happens,
EC_FLAG_QUERY_PENDING will be cleared earlier. As a consequence, the
draining QR_EC will also be queued earlier than expected.
This patch also moves this code into advance_transaction() where QR_EC is
just sent (ACPI_EC_COMMAND_POLL flagged) to fix this issue.

Notes:
1. After introducing the 2 SCI_EVT related handlings into
   advance_transaction(), a next QR_EC can be queued right after writing
   the current QR_EC command and before reading the event. But this still
   hasn't implemented the draining behavior as the draining support
   requires:
     If a previous returned event value isn't 0x00, a draining QR_EC need
     to be issued even when SCI_EVT isn't set.
2. In this patch, acpi_os_execute() is also converted into a seperate work
   item to avoid invoking kmalloc() in the atomic context. We can do this
   because of the previous global lock fix.
3. Originally, EC_FLAGS_EVENT_PENDING is also used to avoid queuing up
   multiple work items (created by acpi_os_execute()), this can be covered
   by only using a single work item. But this patch still keeps this flag
   as there are different usages in the driver initialization steps relying
   on this flag.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=44161Reported-by: NKieran Clancy <clancy.kieran@gmail.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Device Tree is used in many embedded systems to describe the system
configuration to the OS. It supports attaching properties or name-value
pairs to the devices it describe. With these properties one can pass
additional information to the drivers that would not be available
otherwise.

ACPI is another configuration mechanism (among other things) typically
seen, but not limited to, x86 machines. ACPI allows passing arbitrary
data from methods but there has not been mechanism equivalent to Device
Tree until the introduction of _DSD in the recent publication of the
ACPI 5.1 specification.

In order to facilitate ACPI usage in systems where Device Tree is
typically used, it would be beneficial to standardize a way to retrieve
Device Tree style properties from ACPI devices, which is what we do in
this patch.

If a given device described in ACPI namespace wants to export properties it
must implement _DSD method (Device Specific Data, introduced with ACPI 5.1)
that returns the properties in a package of packages. For example:

	Name (_DSD, Package () {
		ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
		Package () {
			Package () {"name1", <VALUE1>},
			Package () {"name2", <VALUE2>},
			...
		}
	})

The UUID reserved for properties is daffd814-6eba-4d8c-8a91-bc9bbf4aa301
and is documented in the ACPI 5.1 companion document called "_DSD
Implementation Guide" [1], [2].

We add several helper functions that can be used to extract these
properties and convert them to different Linux data types.

The ultimate goal is that we only have one device property API that
retrieves the requested properties from Device Tree or from ACPI
transparent to the caller.

[1] http://www.uefi.org/sites/default/files/resources/_DSD-implementation-guide-toplevel.htm
[2] http://www.uefi.org/sites/default/files/resources/_DSD-device-properties-UUID.pdfReviewed-by: NHanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: NJosh Triplett <josh@joshtriplett.org>
Reviewed-by: NGrant Likely <grant.likely@linaro.org>
Signed-off-by: NDarren Hart <dvhart@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

When we have the acpi_device pointer, there is no need to pass the
device's handle to the acpi_bus_xxx_power functions to get/set/update
the device's power state, instead, use the acpi_device_xxx_power
functions directly.

To make this happen for fan module, export acpi_device_update_power.
Signed-off-by: NAaron Lu <aaron.lu@intel.com>
Signed-off-by: NZhang Rui <rui.zhang@intel.com>

Signed-off-by: NZhang Rui <rui.zhang@intel.com>

Newer laptops and tablets that use ACPI may have thermal sensors and
other devices with thermal control capabilities outside the core CPU/SOC,
for thermal safety reasons.
They are exposed for the OS to use via
1) INT3400 ACPI device object as the master.
2) INT3401 ~ INT340B ACPI device objects as the slaves.

This patch introduces a scan handler to enumerate the INT3400
ACPI device object to platform bus, and prevent its slaves
from being enumerated before the controller driver being probed.
Signed-off-by: NZhang Rui <rui.zhang@intel.com>

The use of _PDC is deprecated in ACPI 3.0 in favor of _OSC,
as ARM platform is supported only in ACPI 5.0 or higher version,
_PDC will not be used in ARM platform, so make Make _PDC only for
platforms with Intel CPUs.

Introduce ARCH_MIGHT_HAVE_ACPI_PDC and move _PDC related code in
ACPI processor driver into a single file processor_pdc.c, make x86
and ia64 select it when ACPI is enabled.

This patch also use pr_* to replace printk to fix the checkpatch
warning and factor acpi_processor_alloc_pdc() a little bit to
avoid duplicate pr_err() code.
Suggested-by: NRobert Richter <rric@kernel.org>
Signed-off-by: NHanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>