In original implementation, the revision passed to
these macros contained revision number in lower nibble.

But, later the revision bits (OMAP_REVBITS_XX) were
defined to use omap_revision[15:08] where revision
number is containied in higher nibble.

This patch updates the macros; else incorrect revision
is detected for OMAP35xx devices.
Signed-off-by: NSanjeev Premi <premi@ti.com>

OMAP3xxx and OMAP4430 UART IP blocks have a restriction wrt RX FIFO.
Empty RX fifo read causes an abort.

OMAP3xxx:
	UART IP revision >= 0x52 have this issue
	MVR register format is:
	Bits  Field Name  Description  				Type  Reset
	31:8   RESERVED 					RO  	0x0
	7:4    MAJOR  	Major revision number of the module.  	RO  	0x--
	3:0    MINOR  	Minor revision number of the module.  	RO  	0x--

OMAP4xxx:
	All revisions have this issue
	Revision id check is not used as the format of MVR resigster has changed
	For omap4 MVR register reads as: 0x50410602 => Revision id = 0x0602
	Format of MVR register on omap4 is: (Courtesy: Cousson, Benoit)
	Bits  Field Name  Description  				Type  Reset
	31:30 SCHEME  	Scheme revision number of module  	RO  	0x1
	29:28 RESERVED   					RO  	0x1
	27:16 FUNC  	Function revision number of module  	RO  	0x041
	15:11 RTL  		Rtl revision number of module  	RO  	0x00
	10:8  MAJOR 	Major revision number of the module.  	RO  	0x6
	7:6   CUSTOM  	Custom revision number of the module.  	RO  	0x0
	5:0   MINOR  	Minor revision number of the module.  	RO  	0x02

Override the default 8250 read handler: mem_serial_in()
by a custom handler: serial_in_8250()
which makes sure that RX fifo is not read when empty

tested on zoom3(3630) board

Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Update the hsmmc zoom peripheral configuration to support:
Power saving mode
mmc2 8-bit support
Configure mmc2 as non removable
Signed-off-by: NMadhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The TWL4030 keypad driver is not enabled by default for zoom2 and zoom3
boards.

This patch will enable the same for both zoom2 and zoom3 boards.

Tested on zoom2(3430) and zoom3(3630) boards.
Signed-off-by: NManjunatha GK <manjugk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The runtime detection of OMAP3515 and OMAP3525
was reversed.
Signed-off-by: NSergey Lapin <slapin@ossfans.org>
Signed-off-by: NSanjeev Premi <premi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Otherwise Extreme Lower Power (ELP) wakeup doesn't work properly.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

omap3: zoom2/3: make MMC slot work again

Commit 12f8dfb56 accidentally broke MMC on zoom2/3.
The .vmmc1 field of zoom_twldata was deleted. Restoring it
allows the MMC slot to work again
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Acked-by: NMadhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The existing htcherald_defconfig did not include mux support, which
prevented USB and other functionality from working out of the box.
This change updates the defconfig to add it in.  It also aligns the
defconfig to the -rc8 kernel config.
Signed-off-by: NCory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The patch corrects the issue introduced with one of my earlier patches:
	OMAP: DMA: Fix omapfb/lcdc on OMAP1510 broken when PM set[1]
as pointed out by OMAP subsystem maintainer.

Applies on top of my prevoius patch:
  OMAP: DMA: move LCD DMA related code from plat-omap to mach-omap1[2]

Tested on Amstrad Delta
Compile tested with omap_generic_2420_defconfig

[1] http://patchwork.kernel.org/patch/57922/
[2] http://patchwork.kernel.org/patch/61952/Signed-off-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Remove unused data type omap_gpio_switch_config

Thereby also get rid of following sparse warnings:
arch/arm/plat-omap/include/plat/board.h :121:20:
	warning: dubious bitfield without explicit `signed' or `unsigned'
arch/arm/plat-omap/include/plat/board.h :122:19:
	warning: dubious bitfield without explicit `signed' or `unsigned'
arch/arm/plat-omap/include/plat/board.h :123:24:
	warning: dubious bitfield without explicit `signed' or `unsigned'
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Comment in omap_init_devices asks to keep init calls and their
implementations in alphabetical order, so let it be that way.
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

For NAND devices '2' should be used with GPMC_CONFIG1_DEVICETYPE
instead of '1'.
Signed-off-by: NVimal Singh <vimalsingh@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds new function: omap_serial_init_port(port) that can be
used to initialize only selected UARTs as serial ports. Platforms can
then in their board files call this function instead of omap_serial_init()
if they don't want to use all UARTs as serial ports.
Signed-off-by: NMika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

CM-T35 can be assembled with different set of peripherals thus making
certain interfaces available to user as GPIOs or dedicated pins. Because
of it CM-T35 bootloader sets up mux configuration only for pins
necessary to boot the system and the rest of the mux configuration is
done by the kernel. Besides, having mux configuration in the kernel
allows to minimize dependancy on bootloader.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Enable minimum features to boot omap4430 on es1.0 samples. v2 versions
removes the "CONFIG_SYSFS_DEPRECATED_V2" since it's deprecated. Without
this older file system doesn't boot. One need to upgrade the filesystem
if getting stuck in first init function.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The secondary cores wakes up in time so the wait loop is not
necessary anymore.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The AuxCoreBoot0 and AuxCoreBoot1 can be only accessed in secure
mode. Replace the current code with secure monitor API's to access/modify
these registers.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch fixes the public sram base address and available
size on OMAP4430.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch fixes the OMAP4430 cpu detection. The IC rev detection is
done with hawkeye and rev. Note that rev does not map directly to
defined processor revision numbers as ES1.0 uses value 0.It also fixes
the SCM base address to read the correct ID_CODE register.

Also the cpu_is_omap44xx() and cpu_is_omap443x() correctly populated
instead of always being true
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Pandora board file updates:
- change keycodes of game buttons
  it was decided not to use ABXY layout by the developers.
- drop i2c bus 3 speed to 100kHz
  this is needed for battery monitoring chip to work reliably.
- drop pandora_lcd platform_device
  the older DSS driver was never functional on l-o or mainline
  kernels due to missing panel driver, so remove unneeded
  pandora_lcd platform_device. This also removes last OMAP_TAG
  from the board file.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Defconfig file of Always Innovating OMAP3-based Touch Book
Signed-off-by: NGregoire Gentil <gregoire@gentil.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Board file of Always Innovating OMAP3-based Touch Book
Signed-off-by: NGregoire Gentil <gregoire@gentil.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This change adds MUX pin configuration and clocks for I2C support
to OMAP 730 and 850-based devices.
Signed-off-by: NCory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This change implements USB client side support into the HTC
Herald board configuration.  It uses a similar, but updated
algorithm to initialize the USB as is used in the linwizard
project.
Signed-off-by: NCory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

All of the LCD DMA code in plat-omap/dma.c appears to be OMAP1-only (and
apparently only is available on a subset of OMAP1 chips).

Move this code to mach-omap1/lcd_dma.c.

Tested on OMAP1510 Amstrad Delta.
Compile-tested with omap_generic_2420_defconfig.
Reported-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Reviewed-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Since omapnand driver never find its way into mainline, switch to gen_nand instead.
Following patch is compile tested only, but it is based on code I wrote for
NetStar board and runtime tested it there.
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
Cc: Imre Deak <imre.deak@nokia.com>
Cc: Brian Swetland <swetland@google.com>
Cc: Kevin Hilman <kjh@hilman.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use smc91x_platdata to setup smc91x, so we can get rid of OMAP specific stuff
in smc91x driver
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add 36xx CBP package support

Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Remove old mux code for 34xx
Signed-off-by: NTony Lindgren <tony@atomide.com>

Replace omap_cfg_reg() with new style signal or gpio functions
Signed-off-by: NTony Lindgren <tony@atomide.com>

Otherwise we cannot limit new mux code to mach-omap2.
The same signal names should eventually work for other
omaps under mach-omap2.

Note that these pins don't need to be OMAP_PIN_INPUT_PULLUP,
just OMAP_PIN_INPUT is enough.

Cc: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add debugfs support for new mux code
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add new style mux init functions to omap3 board-*.c files

So far Beagle has been confirmed to be a CBB package,
and CM-T35 a CUS package.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add new style mux data for 34xx. This should also
work with 3630 easily by adding the processor subset
and ball data.

Note that this data is __initdata, and gets optimized
out except for the GPIO pins if CONFIG_OMAP_MUX
is not set.

Also note that this data uses omap3630 naming for
the SDMMC registers instead of 34xx naming with just
MMC.

Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Initially only for 34xx. This code allows us to:

- Make the code more generic as the omap internal signal
  names can stay the same across omap generations for some
  devices

- Map mux registers to GPIO registers that is needed for
  dynamic muxing of pins during off-idle

- Override bootloader mux values via kernel cmdline using
  omap_mux=some.signa1=0x1234,some.signal2=0x1234

- View and set the mux registers via debugfs if
  CONFIG_DEBUG_FS is enabled

Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

intoduce omap_mux_{read,write}
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

An api at init for all dpll nodes seem to be
needed to reparent the dpll clk node to its
bypass clk in case the dpll is in bypass.
If not done this causes sequencing issues at init
during propogate_rate.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>

Most of the dpll api's from dpll.c are reused for OMAP4.
This patch does extend a few api's for OMAP4 support.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>

This patch moves all the dpll control api's to a
common file dpll.c. This is in preperation of omap4
support wherein most of these api's can be reused.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>

This patch adds dummy hooks for OMAP4 dpll api's. Removes
dummy hooks for clkdev api's and enables CLKDEV
for OMAP4.
Also comments clockdomain calls from within the clock
framework as its not supported yet for OMAP4.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>