Declarations and code in common between verbs and PSM are now moved
to exp_rcv.[ch].
Reviewed-by: NMichael J. Ruhl <michael.j.ruhl@intel.com>
Reviewed-by: NMitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: NAshutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Atomic bit tests are used to single errors and the
completion of request submissions. These operations
don't need to be atomic and show to be expensive on
the profile.

Replace each atomic bit operation with a bool type
and a READ_ONCE/WRITE_ONCE pairing.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The atomic SDMA_REQ_SEND_DONE bit is set by the
process-level code, and then the same process-level
code uses the bit to test that all packets have been
submitted incurring a costly atomic read.

Use a bool type with a READ_ONCE/WRITE_ONCE
pairing for this bit, and use the same condition that
is used to set the bit to test that all packets have
been submitted.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The current user SDMA request structure layout has holes.
The cachelines can be reduced to improve cacheline trading.
Separate fields in the following categories: mostly read,
writable and shared with interrupt.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

An RB tree is used for the SDMA pinning cache. Cache
entries are extracted and reinserted from the tree
in case the address range for it changes. However,
if the address range for the entry doesn't change,
deleting the entry from the RB tree is not necessary.

This affects performance since the tree needs to be
rebalanced for each insertion, and this happens in
the hot path. Optimize RB search by not removing
entries when it's not needed.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: NMitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The tx request is unnecessarily initialized in the hot
code path with memset(), however, there's no need to do
this as most fields are initialized later on. this
initialization shows to be costly in the profile.
Remove unnecessary initialization from tx request and make
sure all variables are initialized properly.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The error path for context initialization is not consistent. Cleanup all
resources on failure.

Removed unused variable user_event_mask.

Add the _BASE_FAILED bit to the event flags so that a base context can
notify waiting sub contexts that they cannot continue.

Running out of sub contexts is an EBUSY result, not EINVAL.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NMichael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The AHG index is only accessed in the request call
from user space, so there's no need for atomic semantics.
Replace atomic operations for SDMA_REQ_HAVE_AHG bit
with a test of the AHG index.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Since almost all functions that use the hfi1_filedata get the pointer
from the file pointer, simplify by only passing the hfi1_filedata pointer.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NMichael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

To improve the readability of function prototypes, give the parameters
names.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NMichael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Div instructions show costly in profiles when
the tx request header is set. Using right shift
instead of a divide operation reduces the cycles
spent in the function that sets the tx request
header as shown in the profile. Use right shift
operation instead.

Profile before change:
43.24%  009
|
|--23.41%-- user_sdma_send_pkts
|          |
|          |--99.90%-- hfi1_user_sdma_process_requestAfter:

Profile after change:
45.75%  009
|
|--14.81%-- user_sdma_send_pkts
|          |
|          |--99.95%-- hfi1_user_sdma_process_request
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Replace the specification of a data structure by a reference to
the desired member as the parameter for the operator "sizeof" to make
the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

* Pass a product for a call of the function "vmalloc_user" without storing
  it in an intermediate variable.

* Delete the local variable "memsize" which became unnecessary with
  this refactoring.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

* Multiplications for the size determination of memory allocations
  indicated that array data structures should be processed.
  Thus reuse the corresponding function "kcalloc".

  This issue was detected by using the Coccinelle software.

* Replace the specification of a data type by a pointer dereference
  to make the corresponding size determination a bit safer according to
  the Linux coding style convention.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Set the errcode before the state and add the smb_wmb() to avoid a
potential race condition with the user.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NMichael Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Update several usages of kmalloc/user_copy to memdup_copy and
memdup_copy_nul.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NMichael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

For the received packets with payload less or equal 8DWS
RxDmaDataFifoRdUncErr is not reported. There is set RHF.EccErr
if the header is not suppressed. When such packet is detected
on the send side the header suppression mechanism is disabled
by clearing SH bit in the packet header.
Reviewed-by: NMitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: NJakub Pawlak <jakub.pawlak@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Remove IS_ERR check from caching code as the function being called does
not actually return error pointers.

Fixes: f19bd643: "IB/hfi1: Prevent NULL pointer deferences in caching code"
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Some users want more control over which cpu cores are being used by the
driver. For example, users might want to restrict the driver to some
specified subset of the cores so that they can appropriately partition
processes, irq handlers, and work threads.
To allow the user to fine tune system affinity settings new sysfs
attributes are introduced per sdma engine.  This patch adds a new
attribute type for sdma engine and a new cpu_list attribute.
When the user writes a cpu range to the cpu_list attribute the driver
will create an internal cpu->sdma map, which will be used later as a
look-up table to choose an optimal engine for a user requests.
Reviewed-by: NDean Luick <dean.luick@intel.com>
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Reviewed-by: NJianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: NTadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Each user SDMA request coming into the driver may contain multiple packets.
Each user packet may use multiple SDMA descriptors to fill the send buffer.
The field seqsubmitted in struct user_sdma_request counts the number of
user packets submitted to an SDMA engine. Sometimes, the intermediate count
may not be updated properly. However, once all the packets' descriptors
are successfully submitted to the SDMA engine, the final count is updated
correctly. But, if only some of the packets are submitted to the engine due
to an error, the intermediate count doesn't reflect the partial number of
packets submitted to the SDMA engine. This can cause a hang later in the
code as the count of packets submitted to the SDMA engine doesn't match the
the count of packets processed by the SDMA engine.
Reviewed-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NHarish Chegondi <harish.chegondi@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

In the set_txreq_header_ahg(), The KDETH Intr bit is obtained from the
header in the user sdma request using a KDETH_GET shift and mask macro.
This value is then futher right shifted by 16 causing us to lose the
value i.e it is shifted to zero, leading to the following
smatch warning:
drivers/infiniband/hw/hfi1/user_sdma.c:1482 set_txreq_header_ahg()
warn: mask and shift to zero

The Intr bit should be left shifted into its correct position in the
KDETH header before the AHG update.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NMitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: NHarish Chegondi <harish.chegondi@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The reworked mmu_rb interface allows the unused mm argument to be removed.
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The ops->remove() callback was called by hfi1_mmu_unregister() with a
NULL mm argument while holding a spinlock.  In the case of sdma_rb_remove()
this caused it to pass current->mm to hfi1_release_user_pages()

This had 2 problems.  First this would attempt to acquire the mmap_sem
under a spin lock.  Second the use of current->mm is not always guaranteed
to be the proper mm when the fd is being closed.

Rather than depend on this implicit behavior we move all calls to
ops->remove outside of the spinlock.  This also allows the correct
mm to be used in the remove callback without fear of deadlock.

Because the MMU notifier is not guaranteed to hold mm->mmap_sem, but
usually does, we must delay all remove callbacks until out of the notifier,
when the callbacks can take the mmap_sem if they need to.

Code comments were added to clarify what the expectations are for the
users of the mmu rb tree.
Suggested-by: NJim Foraker <foraker1@llnl.gov>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Use the new cache evict operation in the SDMA code.  This allows the cache
to properly coordinate evicts and removes, preventing any race.  With this
change, the separate list, lock, and race flag are not needed.
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The objects which use cache handling should reference their own handler
object not the internal data structure it uses to track the nodes.

Have the "users" of the mmu notifier code pass opaque objects which can
then be properly used in the mmu callbacks depending on the owners needs.

This patch has the additional benefit that operations no longer require a
look up in a list to find the handlers.
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The hfi1 driver registers a mmu_notifier callback when /dev/hfi1_* is
opened, and unregisters it when the device is closed.  The driver
incorrectly assumes that the close will always happen from the same
context as the open.  In particular, closes due to SIGKILL or OOM killer
activity may happen from a different context.  In these cases, the wrong
mm is passed to mmu_notifier_unregister(), which causes improper reference
counting for the victim mm, and eventual memory corruption.

Preserve the mm for all open file descriptors and use this mm rather than
current->mm for memory operations for the lifetime of that fd.  Note: this
patch leaves 1 use of current->mm in place.  This use is removed in a
follow on patch because other functional changes were required prior to
that use being removed.

If registration fails, there is no reason to keep the handler object
around.  Free the handler object rather than add it to the list to
prevent any mmu_notifier operations, including unregister, when
registration fails.
Suggested-by: NJim Foraker <foraker1@llnl.gov>
Reviewed-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The user SDMA in-use claim bit is in the structure that gets zeroed out
once the claim is made.  Move the request in-use flag into its own bit
array and use that for atomic claims.  This cleans up the claim code and
removes any race possibility.
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

If input validation fails, properly free the request before returning.
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

If unable to insert node into the RB tree cache, node will be freed
before returning from the function.  Null out iovec's pointer to node
so iovec does not try to free it later.
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

If a context has not been assigned or assignment failed, pq may be NULL.
Move the unregister within the protection of the null check.
Reviewed-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

For bool parameters "false" should be used
Reviewed-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Brackets should be on the next line of a function
Reviewed-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The driver pads non-double word multiple message sizes but it doesn't
account for this padding when the packet length is calculated. Also, the
data length is miscalculated for message sizes less than 4 bytes due to
the bit representation in LRH. And there's a check for non-double word
multiple message sizes that prevents these messages from being sent.
This patch fixes length miscalculations and enables the functionality to
send non-double word multiple message sizes.
Reviewed-by: NHarish Chegondi <harish.chegondi@intel.com>
Signed-off-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Currently each user context is assigned a single SDMA engine
based on the VL, context id, and subcontext id. That means for
MPI applications, each rank can only use one SDMA engine for
all messages. This may create unwanted backup for independent
messages going to different destinations upon congestion at one
destination.

This patch adds the packet "dlid" to the formula of SDMA engine
selection for user SDMA requests. A simple hash table is used
to maintain even distribution among the available SDMA engines
regardless how the "dlid" values are distributed.
Reviewed-by: NDean Luick <dean.luick@intel.com>
Reviewed-by: NTadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: NJianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Avoid that sparse reports the following warnings for the hfi1 driver:

trace.c:217:13: warning: no previous prototype for ‘print_u64_array’ [-Wmissing-prototypes]
user_sdma.c:1361:17: warning: dubious: !x & y
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The first argument of test_bit() and clear_bit() is a bit number and
not a bitmask. Hence change that first argument from (1 << 0) into 0.
This patch avoids that smatch reports the following warnings:

user_sdma.c:1059: sdma_cache_evict() warn: test_bit() takes a bit number
user_sdma.c:1590: sdma_rb_remove() warn: test_bit() takes a bit number
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The TODO list for the hfi1 driver was completed during 4.6. In addition
other objections raised (which are far beyond what was in the TODO list)
have been addressed as well. It is now time to remove the driver from
staging and into the drivers/infiniband sub-tree.
Reviewed-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>