Network device features indicate the capabilities of network devices (e.g.,
TX checksum offloading and TSO) and their configuration state. Additional
network device features (vlan_features) indicate for each network device,
which capabilities can be used on VLAN devices, that are configured on the
respective base network device.

In the current qeth implementation, network device features are only set
for the base network devices and not for the VLAN devices. Thus, features
like TX checksum offloading cannot be used on VLAN devices.

This patch adds network device features to vlan_features, so they can be
used by VLAN devices.
Signed-off-by: NHans Wippel <hwippel@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces a common set of fix_features and set_features
functions for layer 2 and layer 3. The RX, TX and TSO offload
functionality on the OSA card is enabled using ethtool at user's
request and not at device initialization as done before.

For layer 3 the RX checksum offloading is disabled at device
initialization time.
Signed-off-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In layer3 mode of the qeth driver, multicast IP addresses
from struct net_device and other type of IP addresses
from other sources require mapping to the OSA-card.
This patch simplifies the IP address mapping logic, and changes imple-
mentation of ndo_set_rx_mode callback and ip notifier events.
Addresses are stored in private hashtables instead of lists now.
It allows hardware registration/removal for new/deleted multicast
addresses only.
Signed-off-by: NLakhvich Dmitriy <ldmitriy@ru.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: NEvgeny Cherkashin <Eugene.Crosser@ru.ibm.com>
Reviewed-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When skb data touches too many pages, skb_linearize() is called
opportunistically in the hope that less pages will be required
for a big linear buffer than for multiple fragments. This patch
intoduces a separate counter in ethtool statistics structure
representing _failed_ linearization attempts.
Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: NLakhvich Dmitriy <ldmitriy@ru.ibm.com>
Reviewed-by: NThomas Richter <tmricht@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set scatter/gather ON by default on OSA, for both layer 2 and
layer 3 modes. We always use fragmentation over QDIO anyway,
so let the upper layers of the stack take advantage of that.
Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: NLakhvich Dmitriy <ldmitriy@ru.ibm.com>
Reviewed-by: NThomas Richter <tmricht@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch enables NETIF_F_SG flag for OSA in layer 2 mode.
It also adds performance accounting for fragmented sends,
adds a conditional skb_linearize() attempt if the skb had
too many fragments for QDIO SBAL, and fills netdevice->gso_*
attributes.
Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: NLakhvich Dmitriy <ldmitriy@ru.ibm.com>
Reviewed-by: NThomas Richter <tmricht@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use QETH_MAX_BUFFER_ELEMENTS(card) instead of constant 16.
Also fill gso_max_segs and gso_min_segs.
Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make conditions under which TSO is activated more stringent.
Make calculation of SBALEs required for the skb more accurate.
Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rewrite the functions that calculate the required number of buffer
elements needed to represent SKB data, to make them hopefully more
comprehensible. Plus a few cleanups.
Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Having understood the semantics of BRIDGEPORT error code 0x0010,
we can introduce a meaningful error message.
Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

kbuild test robot reported a build failure on s390.
While at it, also fix missing conversion in the tilera driver.

Fixes: 9b36627a ("net: remove dev->trans_start")
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace all trans_start updates with netif_trans_update helper.
change was done via spatch:

struct net_device *d;
@@
- d->trans_start = jiffies
+ netif_trans_update(d)

Compile tested only.

Cc: user-mode-linux-devel@lists.sourceforge.net
Cc: linux-xtensa@linux-xtensa.org
Cc: linux1394-devel@lists.sourceforge.net
Cc: linux-rdma@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: MPT-FusionLinux.pdl@broadcom.com
Cc: linux-scsi@vger.kernel.org
Cc: linux-can@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: linux-hams@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: devel@driverdev.osuosl.org
Cc: b.a.t.m.a.n@lists.open-mesh.org
Cc: linux-bluetooth@vger.kernel.org
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Acked-by: NFelipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Acked-by: NAntonio Quartulli <a@unstable.cc>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert the uses of pr_warning to pr_warn so there are fewer
uses of the old pr_warning.

Miscellanea:

o Align arguments
o Coalesce formats
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

0-termination is redundant, since sprintf has done that.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When sending skbs, qeth determines the number of qdio SBAL elements
required. If qeth sends a fragmented skb, the SBAL element number
calculation is wrong, because the fragmented data part is added
twice in qeth_l3_tso_elements(). This patch makes sure fragmented
data is handled in qeth_elements_for_frags() only, while
qeth_l3_tso_elements() starts calculation of qdio SBAL elements just
with the linear data part of the skb.
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

/sys/class/net/<interface>/operstate for an active qeth network
interface offen shows "unknown", which translates to "state UNKNOWN
in output of "ip link show". It is caused by a missing initialization
of the __LINK_STATE_NOCARRIER bit in the net_device state field.
This patch adds a netif_carrier_off() invocation when creating the
net_device for a qeth device.
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Acked-by: NHendrik Brueckner <brueckner@linux.vnet.ibm.com>
Reference-ID: Bugzilla 133209
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There have been 2 identical versions of function
qeth_get_setassparms_cmd() for layer 2 and layer 3.
Remove the layer 3 function qeth_l3_get_setassparms_cmd()
and call the common one named qeth_get_setassparms_cmd()
located in qeth_core_main.c
Signed-off-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The channel_remove() function tests whether its argument is NULL
and then returns immediately. Thus the test around the calls is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In layer2 mode of the qeth driver, MAC address lists
from struct net_device require mapping to the OSA-card.
The existing implementation is inefficient for lists with
more than several MAC addresses, since for every
ndo_set_rx_mode callback it removes all MAC addresses first,
and then registers the current MAC address list.
This patch changes implementation of ndo_set_rx_mode callback
in qeth, only performing hardware registration/removal for
new/deleted addresses. To shorten lookup of MAC addresses
registered addresses are kept in a hashtable instead of a
linear list.
Signed-off-by: NLakhvich Dmitriy <ldmitriy@ru.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Reviewed-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Reviewed-by: NThomas Richter <tmricht@de.ibm.com>
Tested-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for GRO (generic receive offload) in the layer 2
part of device driver qeth. This results in a performance
improvement when GRO and RX is turned on.
Signed-off-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The iucv code uses arrays as arguments. Even though this does not
really cause a problem, it could be misleading, since the compiler
turns array arguments into just a pointer argument. To be more
precise this patch changes the array arguments into pointers.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Checksum offloading for send and receive is already
supported for layer 3 (IP layer). This patch
adds support for RX and TX hardware checksum offloading
for layer 2 (MAC layer). The hardware calculates the checksum
for IP UDP and TCP packets.

This patch moves the hardware checksum offloading setup
to the set of common functions in qeth_core_main.c.
Layer 2 and layer 3 now simply call the same common functions.

Also note that TX checksum offloading is always enabled.
The device driver relies on the TCP/IP stack to make use of
this feature.
Signed-off-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Reviewed-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An OSA-Express port name was required to identify a shared OSA port.
All operating system instances that shared the port had to use the
same port name. This requirement no longer applies.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

User is not allowed to write into bridge_state sysfs file.
Fixed attribute not mislead the user
Signed-off-by: NLakhvich Dmitriy <ldmitriy@ru.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Reported-by: NPeter Oberparleiter <oberpar@linux.vnet.ibm.com>
Reviewed-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Reviewed-by: NThomas Richter <tmricht@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Length specifier in the %pM format is not supported (at least, not
documented). Remove it, and also an extraneous '&' for the array.
Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Suggested-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch remove unneeded variables used to store return values.

These issues were detected with the Coccinelle script:
scripts/coccinelle/misc/returnvar.cocci

[heiko.carstens@de.ibm.com]: make qeth_l[2/3]_stop() return void
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

An attempt to configure a CTC device as LCS results in the
following error message:

  (null): Detecting a network adapter for LCS devices failed
          with rc=-5 (0xfffffffb)

"(null)" results from access to &card->dev->dev in lcs_new_device()
which is only initialized later in the function. Fix this by using
&ccwgdev->dev instead which is initialized before lcs_new_device()
is called.
Signed-off-by: NPeter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since recently, `checkpatch.pl` advices that ENOSYS should not be
used for anything other than "invalid syscall nr". This patch
replaces ENOSYS return code with EOPNOTSUPP for the "unsupported
function" conditions.
Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Forbid enabling IFF_PROMISC reflection to BRIDGEPORT when a role
is already assigned, and forbid direct manipulation of the role
when reflection mode is engaged.
Reviewed-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

OSA Ethernet hardware is introducing BRIDGEPORT functionality
similar (but not identical) to HiperSockets BRIDGEPORT. This
patch makes HiperSockets BRIDGEPORT related sysfs attributes
and udev events work with OSA hardware too.
Reviewed-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

OSA and HiperSocket devices do not support promiscuous mode proper,
but they support "BRIDGE PORT" mode that is functionally similar.
This update introduces sysfs attribute that, when set, makes the driver
try to "reflect" setting and resetting of the IFF_PROMISC flag on the
interface into setting and resetting PRIMARY or SECONDARY bridge port
role on the underlying OSA or HiperSocket device.
Reviewed-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Locking is probably unnecessary in this case, and the rest of the
qeth sysfs code does not use locks in the *_show() functions.
Remove locks from the layer2 *_show() functions in which they where
accidentally introduced.
Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Function that executes IPA commands returns the result code from the
IPA response block. If non-negative, it needs to be transformed into
errno-compatible code before returning to the caller.
Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ethtool is used to change some device driver features
such as RX/TX hardware checksum offloading.
The qeth device driver callback function to
turn on/off RX hardware check sum handling never changes
the hardware configuration.
The NETIF_F_RXCSUM bit is cleared when the feature bitset
type netdev_features_t(64bit) is assigned to 32 a bit
variable.

This patch fixes the NETIF_F_RXCSUM handling.
Also there is no need to manipulate the device's features
bit set as this is done by the caller when no error occurs.
Signed-off-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the 31 bit support in order to reduce maintenance cost and
effectively remove dead code. Since a couple of years there is no
distribution left that comes with a 31 bit kernel.

The 31 bit kernel also has been broken since more than a year before
anybody noticed. In addition I added a removal warning to the kernel
shown at ipl for 5 minutes: a960062e ("s390: add 31 bit warning
message") which let everybody know about the plan to remove 31 bit
code. We didn't get any response.

Given that the last 31 bit only machine was introduced in 1999 let's
remove the code.
Anybody with 31 bit user space code can still use the compat mode.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

This patch adjusts two instances where we were using the (too big)
struct qeth_ipacmd_setadpparms size instead of the commands' actual
size. This didn't do any harm, but wasted a few bytes.
Signed-off-by: NStefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

claw devices are outdated and no longer supported.
This patch removes the claw driver.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do not wait for channel command buffers in IPA commands.
The potential wait could be done while holding a spin lock and causes
in recent kernels such a bug if kernel lock debugging is enabled:

kernel: BUG: sleeping function called from invalid context at drivers/s390/net/qeth_core_main.c:
794
kernel: in_atomic(): 1, irqs_disabled(): 0, pid: 2031, name: NetworkManager
kernel: 2 locks held by NetworkManager/2031:
kernel:  #0:  (rtnl_mutex){+.+.+.}, at: [<00000000006e0d7a>] rtnetlink_rcv+0x32/0x50
kernel:  #1:  (_xmit_ETHER){+.....}, at: [<00000000006cfe90>] dev_set_rx_mode+0x30/0x50
kernel: CPU: 0 PID: 2031 Comm: NetworkManager Not tainted 3.18.0-rc5-next-20141124 #1
kernel:        00000000275fb1f0 00000000275fb280 0000000000000002 0000000000000000
               00000000275fb320 00000000275fb298 00000000275fb298 00000000007e326a
               0000000000000000 000000000099ce2c 00000000009b4988 000000000000000b
               00000000275fb2e0 00000000275fb280 0000000000000000 0000000000000000
               0000000000000000 00000000001129c8 00000000275fb280 00000000275fb2e0
kernel: Call Trace:
kernel: ([<00000000001128b0>] show_trace+0xf8/0x158)
kernel:  [<000000000011297a>] show_stack+0x6a/0xe8
kernel:  [<00000000007e995a>] dump_stack+0x82/0xb0
kernel:  [<000000000017d668>] ___might_sleep+0x170/0x228
kernel:  [<000003ff80026f0e>] qeth_wait_for_buffer+0x36/0xd0 [qeth]
kernel:  [<000003ff80026fe2>] qeth_get_ipacmd_buffer+0x3a/0xc0 [qeth]
kernel:  [<000003ff80105078>] qeth_l3_send_setdelmc+0x58/0xf8 [qeth_l3]
kernel:  [<000003ff8010b1fe>] qeth_l3_set_ip_addr_list+0x2c6/0x848 [qeth_l3]
kernel:  [<000003ff8010bbb4>] qeth_l3_set_multicast_list+0x434/0xc48 [qeth_l3]
kernel:  [<00000000006cfe9a>] dev_set_rx_mode+0x3a/0x50
kernel:  [<00000000006cff90>] __dev_open+0xe0/0x140
kernel:  [<00000000006d02a0>] __dev_change_flags+0xa0/0x178
kernel:  [<00000000006d03a8>] dev_change_flags+0x30/0x70
kernel:  [<00000000006e14ee>] do_setlink+0x346/0x9a0
...

The device driver has plenty of command buffers available
per channel for channel command communication.
In the extremely rare case when there is no command buffer
available, return a NULL pointer and issue a warning
in the kernel log. The caller handles the case when
a NULL pointer is encountered and returns an error.

In the case the wait for command buffer is possible
(because no lock is held as in the OSN case), still wait
until a channel command buffer is available.
Signed-off-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Reviewed-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the functions that are registering and unregistering MAC
addresses in the qeth-handled hardware, remove callback functions
that are unnesessary, as only the return code is analyzed.
Translate hardware response codes to semi-standard 'errno'-like
codes for readability.

Add kernel-doc description to the internal API function
qeth_send_control_data().
Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Reviewed-by: NThomas-Mich Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The member irq_tasklet in the qeth_channel structure
is not referenced anymore and is removed from the
structure.
Signed-off-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>