- 29 10月, 2009 1 次提交
-
-
由 Mikulas Patocka 提交于
CMD646 corrupts data on concurrent transfers on both channels when IDE SSD is connected to one of the channels. Setup that demonstrates this hardware bug: Ultra 5, onboard CMD646, rev 3. /dev/hda is 8GB Seagate ST38410A in MWDMA2 /dev/hdd is 32GB SSD SiliconHardDisk in MWDMA2 - When reading /dev/hdd (for example with dd or fsck), reads from /dev/hda are corrupted, there are twiddled single bits 1->0 and some full 32-bit words corrupted, sometimes commands fail (which switches /dev/hda to PIO mode but the corruptions happen even in PIO). - Reads from /dev/hdd don't seem to be corrupted (i.e. fsck passes fine). - When I connected normal rotating harddisk to /dev/hdd, there was no corruption, so the corruption is something specific to SSD. - I tried the same setup on a PCI card with CMD649 and saw no corruption. This patch serializes the operation for CMD646 and 643 (I didn't test CMD643 but it may have the same hw bug too because it's earlier design). CMD649 is good. I don't know anything about CMD 648. Signed-off-by: NMikulas Patocka <mpatocka@redhat.com> Tested-by: NFrans Pop <elendil@planet.nl> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 22 6月, 2009 1 次提交
-
-
由 David S. Miller 提交于
This begins to fix regressions reported by Frans Pop on his Ultra-10. There are still some funnies left that we are investigating. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 16 6月, 2009 3 次提交
-
-
由 Joao Ramos 提交于
Change ide_drive_t 'drive_data' field from 'unsigned int' type to 'void *' type, allowing a wider range of values/types to be stored in this field. Added 'ide_get_drivedata' and 'ide_set_drivedata' helpers to get and set the 'drive_data' field. Fixed all host drivers to maintain coherency with the change in the 'drive_data' field type. Signed-off-by: NJoao Ramos <joao.ramos@inov.pt> [bart: fix qd65xx build, cast to 'unsigned long', minor Coding Style fixups] Acked-by: NSergei Shtylyov <sshtylyov@ru.montavista.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
由 Sergei Shtylyov 提交于
Convert the driver's two dma_test_irq() methods into test_irq() methods. The driver will now use the standard dma_test_irq() method implementation which allows to remove 'cmd54x_dma_ops' and 'cmd648_dma_ops' that become identical to 'sff_dma_ops'... Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
由 Sergei Shtylyov 提交于
Convert the driver's two dma_end() methods into clear_irq() methods -- the driver will now use the standard dma_end() method implementation, ide_dma_end(). Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 01 4月, 2009 3 次提交
-
-
Set/clear drive->waiting_for_dma flag in the core code instead of in ->dma_setup and ->dma_end methods. There should be no functional changes caused by this patch. Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
Move ide_destroy_dmatable() call out from ->dma_end method to {ide_pc,cdrom_newpc,ide_dma}_intr(), ide_dma_timeout_retry() and sgiioc4_resetproc(). This causes minor/safe behavior changes w.r.t.: * cmd64x.c::cmd64{8,x}_dma_end() * cs5536.c::cs5536_dma_end() * icside.c::icside_dma_end() * it821x.c::it821x_dma_end() * scc_pata.c::__scc_dma_end() * sl82c105.c::sl82c105_dma_end() * tx4939ide.c::tx4939ide_dma_end() v2: * Fix build for CONFIG_BLK_DEV_IDEDMA=n (reported by Randy Dunlap). Cc: Randy Dunlap <randy.dunlap@oracle.com> Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
All custom ->dma_timeout implementations call the generic one thus it is possible to have only an optional method for resetting DMA engine instead: * Add ->dma_clear method and convert hpt366, pdc202xx_old and sl82c105 host drivers to use it. * Always use ide_dma_timeout() in ide_dma_timeout_retry() and remove ->dma_timeout method. * Make ide_dma_timeout() static. There should be no functional changes caused by this patch. Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 27 3月, 2009 1 次提交
-
-
* Rename dma_timer_expiry() to ide_dma_sff_timer_expiry() and export it. * Add ->dma_timer_expiry method and use it to set hwif->expiry for ATA_PROT_DMA protocol in do_rw_taskfile(). * Initialize ->dma_timer_expiry to ide_dma_sff_timer_expiry() for SFF hosts. * Move setting hwif->expiry from ide_execute_command() to its users and drop 'expiry' argument. * Use ide_execute_command() instead of ->dma_exec_cmd in do_rw_taskfile(). * Remove ->dma_exec_cmd method and its implementations. * Unexport ide_execute_command() and ide_dma_intr(). v2: * Fix CONFIG_BLK_DEV_IDEDMA=n build (noticed by Randy Dunlap). * Fix *dma_expiry naming (suggested by Sergei Shtylyov). There should be no functional changes caused by this patch. Cc: Randy Dunlap <randy.dunlap@oracle.com> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 25 3月, 2009 1 次提交
-
-
* Return 0 instead of dev->irq in ->init_chipset implementations. * Fix ->init_chipset method to return 'int' value instead of 'unsigned int' one. This fixes ->init_chipset handling for host drivers (cs5530, hpt366 and pdc202xx_new) for which it is possible for this method to fail. Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 07 1月, 2009 3 次提交
-
-
由 Sergei Shtylyov 提交于
Move apparently misplaced read_sff_dma_status() method from 'struct ide_tp_ops' to 'struct ide_dma_ops', renaming it to dma_sff_read_status() and making only required for SFF-8038i compatible IDE controller drivers (greatly cutting down the number of initializers) as its only user (outside ide-dma-sff.c and such drivers) appears to be ide_pci_check_simplex() which is only called for such controllers... Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
There should be no functional changes caused by this patch. Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 30 12月, 2008 1 次提交
-
-
* Set IDE_HFLAG_SERIALIZE explictly for CMD646. * Remove no longer needed ide_cmd646 chipset type (which has a nice side-effect of fixing handling of unexpected IRQs). Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 22 10月, 2008 1 次提交
-
-
Suggested-by: NRalf Baechle <ralf@linux-mips.org> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 14 10月, 2008 2 次提交
-
-
While at it: - use EXPORT_SYMBOL_GPL() to match the rest of SFF DMA functions Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
Noticed-by: NRussell King <rmk+lkml@arm.linux.org.uk> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 11 10月, 2008 2 次提交
-
-
* Keep pointer to ->init_chipset method also in struct ide_host and set it in ide_host_alloc_all(). * Add ide_pci_suspend() and ide_pci_resume() helpers (default ->suspend and ->resume implementations). * ->init_chipset can no longer be marked __devinit. * Add proper PCI PM support to IDE PCI host drivers (rz1000.c and tc86c001.c are skipped for now since they need to be converted from using ->init_hwif to use ->init_chipset instead). v2: * Cleanup CONFIG_PM #ifdef-s per akpm's suggestion. Cc: Andrew Morton <akpm@linux-foundation.org> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
* Include <linux/ata.h> directly in <linux/ide.h> instead of through <linux/hdreg.h>. * Include <linux/hdreg.h> only when needed. Cc: Christoph Hellwig <hch@infradead.org> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 06 8月, 2008 1 次提交
-
-
Now that we have warm-plug support ->cable_detect method no longer can be be marked __devinit. Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 25 7月, 2008 5 次提交
-
-
There should be no functional changes caused by this patch. Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
Prefix messages from IDE PCI host drivers by driver name instead of marketed chipset name (it is still possible to exactly identify the particular chipset basing on driver messages). As a bonus this provides nice code savings for some drivers: text data bss dec hex filename 3826 112 8 3946 f6a drivers/ide/pci/amd74xx.o.before 2786 112 8 2906 b5a drivers/ide/pci/amd74xx.o.after 764 108 0 872 368 drivers/ide/pci/cs5520.o.before 680 108 0 788 314 drivers/ide/pci/cs5520.o.after 1680 112 4 1796 704 drivers/ide/pci/generic.o.before 1155 112 4 1271 4f7 drivers/ide/pci/generic.o.after 7128 792 0 7920 1ef0 drivers/ide/pci/hpt366.o.before 6984 792 0 7776 1e60 drivers/ide/pci/hpt366.o.after 2800 148 0 2948 b84 drivers/ide/pci/pdc202xx_new.o.before 2523 148 0 2671 a6f drivers/ide/pci/pdc202xx_new.o.after 2831 148 0 2979 ba3 drivers/ide/pci/pdc202xx_old.o.before 2683 148 0 2831 b0f drivers/ide/pci/pdc202xx_old.o.after 3776 112 4 3892 f34 drivers/ide/pci/piix.o.before 2804 112 4 2920 b68 drivers/ide/pci/piix.o.after 4693 116 0 4809 12c9 drivers/ide/pci/siimage.o.before 4600 116 0 4716 126c drivers/ide/pci/siimage.o.after Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
Remove verbose reporting for CMD646 (PCI device revision is always logged by IDE PCI layer). Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
* Add 'struct device *dev[2]' and 'void *host_priv' fields to struct ide_host. * Set ->dev[] in ide_host_alloc_all()/ide_setup_pci_device[s](). * Pass 'void *priv' argument to ide_setup_pci_device[s]() and use it to set ->host_priv. * Set PCI dev's ->driver_data to point to the struct ide_host instance if PCI host driver wants to use ->host_priv. * Rename ide_setup_pci_device[s]() to ide_pci_init_{one,two}(). Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 24 7月, 2008 1 次提交
-
-
* Use ->dma_base + offset instead of ->dma_{status,command} and remove no longer needed ->dma_{status,command}. While at it: * Use ATA_DMA_* defines. There should be no functional changes caused by this patch. Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 17 7月, 2008 1 次提交
-
-
There should be no functional changes caused by this patch. Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 16 7月, 2008 1 次提交
-
-
* Remove obsoleted "idebus=" kernel parameter. * Remove no longer needed ide_system_bus_speed() and system_bus_clock() (together with idebus_parameter and system_bus_speed variables). Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 27 4月, 2008 4 次提交
-
-
* Add "vlb_clock=" parameter for specifying VLB clock frequency (in MHz). * Add "pci_clock=" parameter for specifying PCI bus clock frequency (in MHz). While at it: * qd65xx.c: rename {active,recovery}_cycle variables to {act,rec}_cyc. Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
* Export ide_dma_exec_cmd() and __ide_dma_test_irq(). * Constify struct ide_dma_ops. * Always set hwif->dma_ops to &sff_dma_ops in ide_setup_dma() (it is later overriden by ide_init_port() if needed) and drop 'const struct ide_port_info *d' argument. While at it: * Rename __ide_dma_test_irq() to ide_dma_test_irq(). Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
Add struct ide_dma_ops and convert core code + drivers to use it. While at it: * Drop "ide_" prefix from ->ide_dma_end and ->ide_dma_test_irq methods. * Drop "ide_" "infixes" from DMA methods. * au1xxx-ide.c: - use auide_dma_{test_irq,end}() directly in auide_dma_timeout() * pdc202xx_old.c: - drop "old_" "infixes" from DMA methods * siimage.c: - add siimage_dma_test_irq() helper - print SATA warning in siimage_init_one() * Remove no longer needed ->init_hwif implementations. v2: * Changes based on review from Sergei: - s/siimage_ide_dma_test_irq/siimage_dma_test_irq/ - s/drive->hwif/hwif/ in idefloppy_pc_intr(). - fix patch description w.r.t. au1xxx-ide changes - fix au1xxx-ide build - fix naming for cmd64*_dma_ops - drop "ide_" and "old_" infixes - s/hpt3xxx_dma_ops/hpt37x_dma_ops/ - s/hpt370x_dma_ops/hpt370_dma_ops/ - use correct DMA ops for HPT302/N, HPT371/N and HPT374 - s/it821x_smart_dma_ops/it821x_pass_through_dma_ops/ v3: * Two bugs slipped in v2 (noticed by Sergei): - use correct DMA ops for HPT374 (for real this time) - handle HPT370/HPT370A properly Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
* Move hooks for port/host specific methods from ide_hwif_t to 'struct ide_port_ops'. * Add 'const struct ide_port_ops *port_ops' to 'struct ide_port_info' and ide_hwif_t. * Update host drivers and core code accordingly. While at it: * Rename ata66_*() cable detect functions to *_cable_detect() to match the standard naming. (Suggested by Sergei Shtylyov) v2: * Fix build for bast-ide. (Noticed by Andrew Morton) Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 26 4月, 2008 1 次提交
-
-
"bootable" should be the default behavior so replace IDE_HFLAG_BOOTABLE host flag with IDE_HFLAG_NON_BOOTABLE. There should be no functional changes caused by this patch. Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 03 2月, 2008 2 次提交
-
-
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
* Add ->cable_detect method to ide_hwif_t. * Call the new method in ide_init_port() if: - the host supports UDMA modes > UDMA2 ('hwif->ultra_mask & 78') - DMA initialization was successful (if hwif->dma_base is not set ide_init_port() sets hwif->ultra_mask to zero) - "idex=ata66" is not used ('hwif->cbl != ATA_CBL_PATA40_SHORT') * Convert PCI host drivers to use ->cable_detect method. While at it: * Factor out cable detection to separate functions (if not already done). * hpt366.c/it8213.c/slc90e66.c: - don't check cable type if "idex=ata66" is used * pdc202xx_new.c: - add __devinit tag to pdcnew_cable_detect() * pdc202xx_old.c: - rename pdc202xx_old_cable_detect() to pdc2026x_old_cable_detect() - add __devinit tag to pdc2026x_old_cable_detect() Reviewed-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 02 2月, 2008 3 次提交
-
-
Delete filenames/versions from comments. I'm leaving decisions about adding DRV_VERSION defines and MODULE_VERSION()-s to maintainers of the respective drivers. While at it: * Remove unused VERSION define from ide.c. * Remove unused/stale DRV_VERSION define from au1xxx-ide.c. Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
Keep pointer to struct device instead of struct pci_dev in ide_hwif_t. While on it: * Use *dev->dma_mask instead of pci_dev->dma_mask in ide_toggle_bounce(). There should be no functionality changes caused by this patch. Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
* Rename 'simplex_stat' variable to 'dma_stat' in ide_get_or_set_dma_base(). * Factor out code for forcing host out of "simplex" mode from ide_get_or_set_dma_base() to ide_pci_clear_simplex() helper. * Add IDE_HFLAG_CLEAR_SIMPLEX host flag and set it in alim15x3 (for M5229), amd74xx (for AMD 7409), cmd64x (for CMD643), generic (for Netcell) and serverworks (for CSB5) host drivers. * Make ide_get_or_set_dma_base() test for IDE_HFLAG_CLEAR_SIMPLEX host flag instead of checking dev->device (BTW the code was buggy because it didn't check for dev->vendor, luckily none of these PCI Device IDs was used by some other vendor for PCI IDE controller). Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 27 1月, 2008 1 次提交
-
-
This belongs to user-space (and only if really needed). text data bss dec hex filename 3874 180 28 4082 ff2 drivers/ide/pci/cmd64x.o.before 2231 180 0 2411 96b drivers/ide/pci/cmd64x.o.after Additionaly to being bloat the code reported incorrect UDMA modes for the reserved values of UDIDETCR0/1 registers. Also while at it remove unused CNTRL_DIS_RA0/1 defines. Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 26 1月, 2008 1 次提交
-
-
* Add IDE_HFLAG_ABUSE_SET_DMA_MODE host flag and use it to decide what to do with transfer modes < XFER_PIO_0 in ide_set_xfer_rate(). * Set IDE_HFLAG_ABUSE_SET_DMA_MODE in host drivers that need it (aec62xx, amd74xx, cs5520, cs5535, hpt34x, hpt366, pdc202xx_old, serverworks, tc86c001 and via82cxxx) and cleanup ->set_dma_mode methods in host drivers that don't (IDE core code guarantees that ->set_dma_mode will be called only for modes which are present in SWDMA/MWDMA/UDMA masks). While at it: * Add IDE_HFLAGS_HPT34X/HPT3XX/PDC202XX/SVWKS define in hpt34x/hpt366/pdc202xx_old/serverworks host driver. There should be no functionality changes caused by this patch. Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-