Add scale_available attribute.
fix ad7152_scale_table, values are not sorted descending.
Use IIO_VAL_INT_PLUS_NANO, to increase granularity.
Update scale handling accordingly.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove unused define.
Introduce cached SETUP variables.
Wait until calibration finished. (Device returns to idle state)
IIO_CHAN_INFO_CALIBSCALE_SEPARATE use proper scales. (range 1.0 to 1.99999)
i2c_smbus word transactions expect low byte first, therefore swap bytes.
CAPDIFF is bit in SETUP not CFG.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some other miscellaneous cleanup.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Get rid of explicit writes to registers and conversion mode
control.

Couple of bits I'm unsure about.
* Do calibration modes self reset when done?  How do you tell they are
done?

* Should we poll the status register just to be sure we have a new conversion?

All done sans hardware.
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Acked-by: NMichael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Has been broken for some time.
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Acked-by: NMichael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is fine IF I  have read the data sheet correctly.
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Acked-by: NMichael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The AD7150 features two outputs that can be used as interrupt strobes
to the host processor. In order to receive all events independently,
both need to utilized.

Update copyright notice.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The AD7150 family of devices power up in continues conversion mode.
We can stay in this mode, unless power consumption becomes a real issue.
Actually the event generation as well as the running average
relies on continues conversion mode, so we better stay there.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Minimal changes to code layout as going to do chan spec conversion shortly.
Otherwise, there are numerous code sharing opportunities in here and abi
elements that are uterly non compliant.
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Acked-by: NMichael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Acked-by: NMichael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Straight forward change in the core, but required some drivers to not use
the IIO_CHAN macro as that doesn't allow setting this bit (and is
going away anyway). Hence the churn.

Tested on max1363 with a couple of supported parts.

V2: differential bit in code got 7 bits and direction 1. Reversed that.
Issue spotted by Michael - thanks!
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Acked-by: NMichael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I'm not entirely sure this is the right way to go. Suggestions of other
options welcome!
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

These are both needed for CAPADCs
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Acked-by: NMichael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Should always have been IIO_EV_DIR_MAX as that's what it actually controls.
Also reduced the number to 4 as not yet seen a case needing more and this
is not userspace visible anyway.
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Makes unusual event related attributes look a lot more like the core ones.

V2: Make sure the utils that set these up can handle the codes.
V3: rebase
Reported-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This set also includes quite a number of bug fixes of particularly
remove functions.

Necessary due to issue pointed out in Bart Van Assche's patch:
docs/driver-model: Document device.groups

V2: Rebase due to patch reordering.
V3: Pull various error fixes and cleanups out into their own patches.
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Acked-by: NMichael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This costs us nothing in event storage (as we are carrying a 64 bit
timestamp in the structure) and gives us lots more room to play with.

Also allows for more channels which some parts need.

V2: Cleanup some loose ends (such as the switch with only one option now).
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is as light as possible on changes to current drivers.
Some drivers make assumptions that their masks fit in a single
long.  Given they were previously working this is clearly valid if
not tidy.

The max1363 is an example where there should be no such assumptions.

V2: Add the new ad5933
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Acked-by: NMichael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The scan mask will be dynamically assigned in register, so don't
use it before that.

In adis16260 I've moved it as I know this driver has userspace code.
Same for sca3000 where it is cost free due to hardware buffer.
Can do that for the others, but in theory userspace code should always
have been checking these and setting them appropriately anyway!

V2: Clear default mask out of adis16400 as reported by Michael
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Reported-by: NMichael Hennerich <michael.hennerich@analog.com>
Acked-by: NMichael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If not set in chan_spec, cpu endianness used.
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Also includes the inX -> in_voltageX and outX -> out_voltageX conversions.
To keep lines short quite a lot of supressing of directories was needed.
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Also involves changing current inX outX to in_voltageX and out_voltageX

V2: squash users of the IIO_CHAN_OUT macro and get rid of it.
There are very few of these, so it is easier to fix them.
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Acked-by: NMichael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

No way iio_device_allocate or iio_device_unregister effected
by regulators so copying tricks not needed.

This is really about regularizing the layout of drivers.
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This includes calling iio_free_device as that should only be called
before the device has been registered.

Also one case of iio_free_device being called on a registered device.

This has been pulled out of the reworking attributes patch.
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Guessing this is some ancient cut and paste issue.
Signed-off-by: NJonathan Cammeron <jic23@cam.ac.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This avoids issues in the new event code introduced shortly + makes
moving this one out of staging easier.
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

These are no longer needed.
Requires a few driver updates for places "sysfs.h" should have been
present but wasn't.
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Now the old method is long gone, lets get rid of the _ex and whilst
here remove the unused id parameter.

Trivial mechanical change, but will break any out of tree drivers
using this.

V2: rebase
V3: rebase
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Introduce IIO_RAW and IIO_PROCESSED and an array for their strings.
Also move one function to just above where it is called.
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I have no idea what this was, or what it did, but it doesn't
do it any more.
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

All iio dependent modules statically depend on industrialio
so these aren't needed. Not sure why they originally existed,
but they aren't now.
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use new simple ida allocation functions to remove some boilerplate
code.

Also, now we only have one chdev per device we don't need to maintain
a separate ida for minor numbers. Just use the devices id.
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We don't have a use case for these.  Two drivers appeared to use them
but both report all events on the first.

V2: Remove now irrelevant comment.
V3: Include fixup for adc/ad7280a.c
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Acked-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

A few element in here have been wrong for some time so cleaned them
up whilst here.
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Now we have combined all chrdevs into one, some bits and bobs are only
needed in industrialio-core.c and don't need to be in the core header.

Also remove some unused defines.
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Sorry all, this one is very invasive, though the driver changes are
just trivial interface fixes. Not all done yet.

V2 - bring the sca3000 with us.
V3 - fix ade7758 bugs in conversion.
V4 - add ad5933
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Acked-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This no longer has any purpose given all chrdevs are pretty much the same
now the event interfaces are done via anon fds
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>