Add tracing support to forward management and data frames to
user space for packet inspection.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fix WMI scan command length we setup when scan request.

This fix issue with 636 firmware when scan always failed
with message:

ath10k_pci 0000:02:00.0: wmi start scan
ath10k_pci 0000:02:00.0: wmi stop scan reqid 1 req_type 0 vdev/scan_id 0
ath10k_pci 0000:02:00.0: failed to stop wmi scan: -11
ath10k_pci 0000:02:00.0: failed to stop scan: -11
ath10k_pci 0000:02:00.0: failed to start hw scan: -110
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is required if we take into account possibility to load the driver
from initrd (RAM disk), so in other words: very early in the boot process,
before the file system is visible.

In such case we need to have the firmware files accessible from ram disk too,
and this patch guarantee this.
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It's not really necessary to create bssid peer for
bssid. Self-address peer is sufficient.

This prevents some firmware revisions from crashing.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It makes a lot more sense to print these kinds of
problems as a warning instead of a debug.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The tx info such as msdu_id, frame len, vdev id and tid are reported
to user space by tracepoint. This is useful for collecting tx
statistics.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Upon the reception of frame, the descriptor status are reported
to user space by tracepoint. This is useful for collecting rx
statistics.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is useful for collecting pktlog statistics of tx, rx
and rate information, so add tracing for the API call.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add support to configure packet log filters (tx, rx, rate control)
via debugfs. To disable htt pktlog events set the filters to 0.

ex:

To enable pktlog for all filters

   echo 0x1f > /sys/kernel/debug/ieee80211/phy*/ath10k/pktlog_filter

To disable pktlog

   echo 0 > /sys/kernel/debug/ieee80211/phy*/ath10k/pktlog_filter
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This can allow more than 32 stations to be supported
without over-running the bitmap.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add support for reading firmware stats through the ethtool
API.  This may be easier for applications to manipulate
compared to parsing a text based debugfs file.

kvalo: remove unneeded ifdefs, call ath10k_debug_fw_stats_request() and added
simple error handling
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add three counters related to firmware crashes or resets.

Usage:

# cat /sys/kernel/debug/ieee80211/phy0/ath10k/fw_reset_stats
fw_crash_counter                2
fw_warm_reset_counter           43
fw_cold_reset_counter           0
#

kvalo: split into it's own patch, add debugfs file and add locking
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If stat data exceeds wmi-htc buffer limits
firmware splits it into many wmi stats update
events which are delivered in a ping-pong fashion
triggered by wmi stats request command.

Since there's only an implicit start-of-data and
no end-of-data indications the driver has to
perform some trickery to get complete stat data.

kvalo: use %zu to fix a compiler warning and fix a typo in a comment
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Stats were requested and processed for each read
call. This caused inconsistent readings.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The naming was a bit inconsistent.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The parsing function was rather complex. Simplify
by splitting it up into firmware branch specific
implementations.

While at it move the parsing code into wmi.c where
it belongs.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The return values are not used by callers of these functions
so change the functions to return void.

Other miscellanea:

o add __printf verification to wil6210 logging functions
  No format/argument mismatches found
Acked-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Provide calibration data used by the firmware to user space via a debugfs file.
This makes it easier to debug calibration related problems.

Example:

sudo cp /sys/kernel/debug/ieee80211/phy0/ath10k/cal_data 1.cal
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

diag_read() is used for reading from firmware memory via the diagnose window.
First user will be cal_data debugfs file.

To serialise diagnostic window access and make it safe to use while firmware is
running take ce_lock both in ath10k_pci_diag_write_mem() and
ath10k_pci_diag_read_mem(). Because of that all the CE calls had to be changed
to _nolock variants.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The diagnostic window (CE7) uses polling and is not initiliased to retrieve
interrupts so disable interrupts altogether for CE7. Otherwise ath10k crashes
when using the diagnostic window while the firmware is running due to NULL
dereference and polling reads timeout.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This makes it easier to debug the device-target
communication at a very low level.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This makes it easier to debug hex dumps on systems
with more than a single ath10k device.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

HTT version is already printed so print WMI
version as well for consistency.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This gets rid of the ugly scan structure building
and uses a saner way to do it.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Make all wmi event functions match the same naming
style, i.e. ath10k_wmi_event_<name>.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Make the phyerr structures more compact and easier
to understand. Also add constness.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The logic responsible for processing the event is
no different across different firmware binaries.
The difference that needs to be dealt with is the
ABI of data structures.

The intermediate structure uses __le32 to avoid
extra memory allocations to byteswap
variable-length substructures (i.e. host mem
chunks).
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Init functions should be placed at the end of
files in most cases to avoid forward declarations
for static functions.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Simplify the code by deduplicating structure
definitions and code.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The structure is being set up in 2 places.
Deduplicate the code by creating a helper.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This command is not used anymore and most firmware
revisions do not seem to handle it well. Channel
switching is done via vdev restarting.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware reports the number of RF chains so use
that for initialization of supp_{tx,rx}_chainmask
instead of using a macro for 3x3 chips.

This should make tx/rx chainmask reports correct
for chips other than 3x3.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Some firmware revisions don't wait for beacon tx
completion before sending another SWBA event. This
could lead to hardware using old (freed) beacon
data in some cases, e.g. tx credit starvation
combined with missed TBTT. This is very very rare.

On non-IOMMU-enabled hosts this could be a
possible security issue because hw could beacon
some random data on the air.  On IOMMU-enabled
hosts DMAR faults would occur in most cases and
target device would crash.

Since there are no beacon tx completions (implicit
nor explicit) propagated to host the only
workaround for this is to allocate a DMA-coherent
buffer for a lifetime of a vif and use it for all
beacon tx commands. Worst case for this approach
is some beacons may become corrupted, e.g. garbled
IEs or out-of-date TIM bitmap.

Keep the original beacon-related code as-is in
case future firmware revisions solve this problem
so that the old path can be easily re-enabled with
a fw_feature flag.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

As suggeested by checkpatch:

WARNING: Prefer ether_addr_copy() over memcpy() if the Ethernet addresses are __aligned(2)

In wmi.c I had to change due to sparse warnings copying of struct wmi_mac_addr
from form &cmd->peer_macaddr.addr to cmd->peer_macaddr.addr. In
ath10k_wmi_set_ap_ps_param() I also added the missing ".addr" to the copy
command.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Makes it more readable and fixes checkpatch warnings:

drivers/net/wireless/ath/ath10k/debug.c:593: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:594: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:595: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:596: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:597: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:599: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:600: WARNING: quoted string split across lines
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fixes checkpatch warnings:

ath10k/htc.c:49: WARNING: Possible unnecessary 'out of memory' message
ath10k/htc.c:810: WARNING: Possible unnecessary 'out of memory' message
ath10k/htt.h:1034: CHECK: Please use a blank line after function/struct/union/enum declarations
ath10k/htt_rx.c:135: CHECK: Unnecessary parentheses around htt->rx_ring.alloc_idx.vaddr
ath10k/htt_rx.c:173: CHECK: Unnecessary parentheses around htt->rx_ring.alloc_idx.vaddr
ath10k/pci.c:633: WARNING: macros should not use a trailing semicolon
ath10k/wmi.c:3594: WARNING: quoted string split across lines
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fixes checkpatch warnings:

WARNING: else is not generally useful after a break or return
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fixes a checkpatch warning:

WARNING: void function return statements are not generally useful
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fixes checkpatch warnings:

CHECK: No space is necessary after a cast
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fixes checkpatch warnings:

WARNING: Missing a blank line after declarations

Please note that some of the cases I fixed by moving the variable declarations
to the beginning of the function, which is the preferred style in ath10k.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>