- 18 10月, 2018 1 次提交
-
-
由 Ido Schimmel 提交于
When the switch driver (e.g., mlxsw_spectrum) determines it needs to flash a new firmware version it resets the ASIC after the flashing process. The bus driver (e.g., mlxsw_pci) then registers itself again with mlxsw_core which means (among other things) that the device registers itself again with the hwmon subsystem again. Since the device was registered with the hwmon subsystem using devm_hwmon_device_register_with_groups(), then the old hwmon device (registered before the flashing) was never unregistered and was referencing stale data, resulting in a use-after free. Fix by removing reliance on device managed APIs in mlxsw_hwmon_init(). Fixes: c86d62cc ("mlxsw: spectrum: Reset FW after flash") Signed-off-by: NIdo Schimmel <idosch@mellanox.com> Reported-by: NAlexander Petrovskiy <alexpe@mellanox.com> Tested-by: NAlexander Petrovskiy <alexpe@mellanox.com> Reviewed-by: NPetr Machata <petrm@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 10 8月, 2018 2 次提交
-
-
由 Jiri Pirko 提交于
Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiri Pirko 提交于
Recent FW fixes a bug and allows to load newly flashed FW image after reset. So make sure the reset happens after flash. Indicate the need down to PCI layer by -EAGAIN. Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 06 6月, 2018 1 次提交
-
-
由 David Ahern 提交于
Return messages in extack for port split/unsplit errors. e.g., $ devlink port split swp1s1 count 4 Error: mlxsw_spectrum: Port cannot be split further. devlink answers: Invalid argument $ devlink port unsplit swp4 Error: mlxsw_spectrum: Port was not split. devlink answers: Invalid argument Signed-off-by: NDavid Ahern <dsahern@gmail.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Acked-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 29 5月, 2018 1 次提交
-
-
由 Jiri Pirko 提交于
So far, the PCI BAR0 register is used for triggering FW reset. However, that is a legacy attitude and it is recommended to use MRSR to perform reset instead. So do that. Move the reset into init() function as the cmd interface needs to be used. With that, IRQ initialization needs to be moved as well. As a side effect, the reset move simplifies the devlink reload flow. Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 20 5月, 2018 2 次提交
-
-
由 Jiri Pirko 提交于
Since devlink knows the info needed to generate the physical port name in a generic way for all devlink users, use the helper to do the job. Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiri Pirko 提交于
Change existing setter for split port information into more generic attrs setter. Alongside with that, allow to set port number and subport number for split ports. Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 01 4月, 2018 4 次提交
-
-
由 Jiri Pirko 提交于
As struct mlxsw_config_profile is mapped to the payload of the FW command of the same name, resources_query_enable flag does not belong there. Move it to struct mlxsw_driver. Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiri Pirko 提交于
The check should be done directly in mlxsw_pci_config_profile, as for other profile items. Also, be consistent in naming with the rest and rename to "used_kvd_sizes". Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiri Pirko 提交于
First arg of these helpers should be "mlxsw_core". Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiri Pirko 提交于
This should not be part of the struct, as the struct fields are tightly coupled with the FW command payload of the same name. Just use the "granularity" define directly, as in other places. Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 17 1月, 2018 4 次提交
-
-
由 Arkadi Sharshevsky 提交于
Add support for hot reload. First, all the driver/core resources are released but the PCI and devlink instances, then reset is performed through the PCI interface. Finally the driver performs initialization. In case of reload failure the driver is left in a partially initialized state. Special care is taken during the driver removal in order to properly handle this state. Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Arkadi Sharshevsky 提交于
Up until now the KVD partition was static. This patch introduces the ability to get the resource sizes via devlink. In case the resource is not available the default configuration is used. Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Arkadi Sharshevsky 提交于
Register the KVD resources with devlink. The KVD is a memory resource which is subdivided into three partitions which are the linear, hash single and hash double. Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Arkadi Sharshevsky 提交于
This is a preparation stage before introducing hot reload. During the reload process the ASIC should be resetted by accessing the PCI BAR due to unavailability of the mailbox/emad interfaces. Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 26 5月, 2017 1 次提交
-
-
由 Yotam Gigi 提交于
This struct was previously an anonymous struct defined inside the mlxsw_bus_info struct. Extract it to a struct named mlxsw_fw_rev, as it will be needed later by the spectrum driver. Signed-off-by: NYotam Gigi <yotamg@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 25 3月, 2017 1 次提交
-
-
由 Ido Schimmel 提交于
We currently hard code the maximum number of ports in the driver, but this may change in future devices, so query it from the firmware instead. Fallback to a maximum of 64 ports in case this number can't be queried. This should only happen in SwitchX-2 for which this number is correct. Signed-off-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 07 2月, 2017 1 次提交
-
-
由 Ido Schimmel 提交于
We always use zero delay before queueing a work on the ordered workqueue ('mlxsw_owq'), so use work_struct directly instead of delayable work. Signed-off-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 04 12月, 2016 1 次提交
-
-
由 Ido Schimmel 提交于
We're going to start processing FIB entries addition / deletion events in deferred work. These work items must be processed in the order they were submitted or otherwise we can have differences between the kernel's FIB table and the device's. Solve this by creating an ordered workqueue to which these work items will be submitted to. Note that we can't simply convert the current workqueue to be ordered, as EMADs re-transmissions are also processed in deferred work. Later on, we can migrate other work items to this workqueue, such as FDB notification processing and nexthop resolution, since they all take the same lock anyway. Signed-off-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 26 11月, 2016 6 次提交
-
-
由 Nogah Frankel 提交于
Currently, the emad trap init was done in the core. In the future we will want to add some changes to the traps groups, according to device type. This commit create a driver function to create the trap group for the emad, so later it can be changed by devices. It also changes the emad registration to use the new generic functions. Signed-off-by: NNogah Frankel <nogahf@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Nogah Frankel 提交于
Currently, we set the trap group to pre-determined option, based on whether it is an rx or event trap. This commit adds a possibility to chose the trap group, so it can be set to different values in the following patches. Signed-off-by: NNogah Frankel <nogahf@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Nogah Frankel 提交于
Change trap setting function so instead of determining the trap group by trap id, it gets it as a parameter (so later we can have different trap groups for Spectrum and Switchx2). Add "is_ctrl" parameter to the trap setting function. It control whether the trapped packets wait in a designated control buffer or in their default one. This parameter is ignored by Switchx2 and Switchib. Add these parameters to the traps array in Spectrum, Switchx2 and Switchib. Signed-off-by: NNogah Frankel <nogahf@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Nogah Frankel 提交于
Create a macro for creating the generic listener struct for events, similar to the one for rx traps. Signed-off-by: NNogah Frankel <nogahf@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Nogah Frankel 提交于
In Spectrum, there is a macro to arrange the traps list. This macro is useful for everyone who is using rx traps. Create a similar macro in core.h for creating the generic listener struct for rx traps. Signed-off-by: NNogah Frankel <nogahf@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Nogah Frankel 提交于
We have 2 types of HW traps to handle, rx traps and events. The registration workflow for both is very similar. So it only make sense to create one function to handle both. This patch creates a struct to hold the data for both cases. It also creates a registration and an un-registration functions that get this generic struct as input. Signed-off-by: NNogah Frankel <nogahf@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 22 11月, 2016 1 次提交
-
-
由 Ivan Vecera 提交于
Implement thermal zone for mlxsw based HW. It uses temperature sensor provided by ASIC (the same as mlxsw hwmon interface) to report current temp to thermal core. The ASIC's PWM is then used to control speed of system fans registered as cooling devices. Signed-off-by: NIvan Vecera <cera@cera.cz> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 17 11月, 2016 1 次提交
-
-
由 Vadim Pasternak 提交于
The mlxsw core infrastructure currently assumes that communication with the ASIC is always possible using Ethernet management datagrams (EMADs), but this is only possible when the PCI bus is used. The bus capability flag is added to indicate EMAD support and make core initialize EMAD communication only when it's set. Otherwise, register access is done using command interface. Signed-off-by: NVadim Pasternak <vadimp@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 31 10月, 2016 3 次提交
-
-
由 Elad Raz 提交于
Add "port_type_set" API to mlxsw core. The core layer send the change type callback to the port along with it's private information. Signed-off-by: NElad Raz <eladr@mellanox.com> Reviewed-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Elad Raz 提交于
Since we are about to introduce IB port APIs, we will add prefixes to existing APIs. Signed-off-by: NElad Raz <eladr@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiri Pirko 提交于
Currently, devlink register/unregister is done directly from spectrum/switchx2 port create/remove functions. With a need to introduce a port type change, the devlink port instances have to be persistent across type changes, therefore across port create/remove function calls. So do a bit of reshuffling to achieve that. Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NElad Raz <eladr@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 29 10月, 2016 1 次提交
-
-
由 Jiri Pirko 提交于
So far, mlxsw_pci.ko is the module that registers PCI table for all drivers (spectrum and switchx2). That is problematic for example with dracut. Since mlxsw_spectrum.ko and mlxsw_switchx2.ko are loaded dynamically from within mlxsw_core.ko, dracut does not have track of them and avoids them from being included in initramfs. So make this in an ordinary way and define the PCI tables in individual driver modules, so it can be properly loaded and included in dracut initramfs image. As a side effect, this patch could remove no longer necessary driver "kind" strings which were used to link PCI ids with individual mlxsw drivers. Suggested-by: NIvan Vecera <ivecera@redhat.com> Tested-by: NIvan Vecera <ivecera@redhat.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Acked-by: NIvan Vecera <ivecera@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 24 10月, 2016 1 次提交
-
-
由 Jiri Pirko 提交于
Since the number of resources is going to get much bigger, ease up the addition by simly defining IDs. Convert the existing structure members to a set array, one for validity, one for values. Introduce a set of getters and setters for easy access. Signed-off-by: NJiri Pirko <jiri@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 21 9月, 2016 7 次提交
-
-
由 Nogah Frankel 提交于
Add the max number of rif (router interfaces) to resource query. Signed-off-by: NNogah Frankel <nogahf@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Nogah Frankel 提交于
Add max system ports, max regions and max vlan groups to resource query. Signed-off-by: NNogah Frankel <nogahf@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Nogah Frankel 提交于
Add the max number of virtual routers to resource query. Signed-off-by: NNogah Frankel <nogahf@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Nogah Frankel 提交于
Use resources from resource query to determine values for the profile configuration. Add KVD determined section sizes to the resources struct. Change the profile struct and value to match this changes. Signed-off-by: NNogah Frankel <nogahf@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Nogah Frankel 提交于
Add KVD size, and minimum sizes for the single and double sections resources to resources query. Signed-off-by: NNogah Frankel <nogahf@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Nogah Frankel 提交于
Use max lag and max ports in lag resources as the result of resource query instead of using const to save them. Signed-off-by: NNogah Frankel <nogahf@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Nogah Frankel 提交于
Add max lag and max ports in lag resources to resources query. Signed-off-by: NNogah Frankel <nogahf@mellanox.com> Reviewed-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 27 8月, 2016 1 次提交
-
-
由 Ido Schimmel 提交于
Up until now we only trapped packets to CPU, but we are going to allow some packets to be mirrored (trap & forward) to CPU. Extend the Rx listener with 'action' member. Signed-off-by: NIdo Schimmel <idosch@mellanox.com> Signed-off-by: NJiri Pirko <jiri@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-