Reorganize the i40e_pull_tail() logic, doing it in i40e_add_rx_frag()
where it's cheaper.  The igb driver does this the same way.

Also renames i40e_page_is_reserved() to reflect what it actually
tests.

Change-ID: Icd9cc507aae1fcdc02308b3a09034111b4c24071
Signed-off-by: NScott Peterson <scott.d.peterson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch reduces the size of struct i40e_rx_buffer by one pointer,
and makes the i40e driver a little more consistent with the igb driver
in terms of packets that span buffers.

We do this by moving the skb field from struct i40e_rx_buffer to
struct i40e_ring. We pass the skb we already have (or NULL if we
don't) to i40e_fetch_rx_buffer(), which skips the skb allocation if we
already have one for this packet.

Change-ID: I4ad48a531844494ba0c5d8e1a62209a057f661b0
Signed-off-by: NScott Peterson <scott.d.peterson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

On packet RX, we perform a DMA sync for CPU before passing the
packet up.  Here we limit that sync to the actual length of the
incoming packet, rather than always syncing the entire buffer.

Change-ID: I626aaf6c37275a8ce9e81efcaa773f327b331487
Signed-off-by: NScott Peterson <scott.d.peterson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch does some quick work to pull some of the data off of the stack
and hopefully start storing it in the Tx buffer info section of the Tx
ring.  Ideally we should be moving away from having to store much of
anything on the stack and can just maintain it all in the descriptor rings.

Change-ID: I4b4715ea1920e122502482b3f9e56a9a6cb1e9fe
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently the function i40e_napi-poll() returns 0 when it clean completely
the Rx rings, but this foul budget accounting in core code.

Fix this by returning the actual work done, capped to budget - 1, since
the core doesn't allow to return the full budget when the driver modifies
the NAPI status

This is based on a similar change that was made for the ixgbe driver by
Paolo Abeni.

Change-ID: Ic3d93ad2fa2fc8ce3164bc461e69367da0f9173b
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch reorders the logic at the end of i40e_tx_map to address the
fact that the logic was rather convoluted and much larger than it needed
to be.

In order to try and coalesce the code paths I have updated some of the
comments and repurposed some of the variables in order to reduce
unnecessary overhead.

This patch does the following:
1.  Quit tracking skb->xmit_more with a flag, just max out packet_stride
2.  Drop tail_bump and do_rs and instead just use desc_count and td_cmd
3.  Pull comments from ixgbe that make need for wmb() more explicit.

Change-ID: Ic7da85ec75043c634e87fef958109789bcc6317c
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a common method for finding a VSI by type.  The main
motivation for doing this is that the Flow Director path actually had two
ways of handling this, one stopped on first match and one did not.  This
patch makes it so that all callers of this function will get the same
approach for finding a VSI.

Change-ID: Ibf25de8acd8466582520694424aa87da66965fbd
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NBimmy Pujari <bimmy.pujari@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The current Rx timestamp hang logic is not very robust because it does
not notice a register is hung until all four timestamps have been
latched and we wait a full 5 seconds. Replace this logic with a newer Rx
hang detection based on storing the jiffies when we first notice
a receive timestamp event. We store each register's time separately,
along with a flag indicating if it is currently latched. Upon first
transitioning to latch, we will update the latch_events[i] jiffies
value. This indicates the time we first noticed this event. The watchdog
routine will simply check that the either the flag has been cleared, or
we have passed at least one second. In this case, it is able to clear
the Rx timestamp register under the assumption that it was for a dropped
frame. The benefit if this strategy is that we should be able to
detect and clear out stalled RXTIME_H registers before we exhaust the
supply of 4, and avoid complete stall of Rx timestamp events.

Change-ID: Id55458c0cd7a5dd0c951ff2b8ac0b2509364131f
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When hardware has taken a timestamp for a received packet, it indicates
which RXTIME register the timestamp was placed in by some bits in the
receive descriptor. It uses 3 bits, one to indicate if the descriptor
index is valid (ie: there was a timestamp) and 2 bits to indicate which
of the 4 registers to read. However, the driver currently does not check
the TSYNVALID bit and only checks the index. It assumes a zero index
means no timestamp, and a non zero index means a timestamp occurred.
While this appears to be true, it prevents ever reading a timestamp in
RXTIME[0], and causes the first timestamp the device captures to be
ignored.

Fix this by using the TSYNVALID bit correctly as the true indicator of
whether the packet has an associated timestamp.

Also rename the variable rsyn to tsyn as this is more descriptive and
matches the register names.

Change-ID: I4437e8f3a3df2c2ddb458b0fb61420f3dafc4c12
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch cleans up several pieces of redundant code in the Rx clean-up
paths.

The first bit is that hdr_addr and the status_err_len portions of the Rx
descriptor represent the same value.  As such there is no point in setting
them to 0 before setting them to 0.  I'm dropping the second spot where we
are updating the value to 0 so that we only have 1 write for this value
instead of 2.

The second piece is the checking for the DD bit in the packet.  We only
need to check for a non-zero value for the status_err_len because if the
device is done with the descriptor it will have written something back and
the DD is just one piece of it.  In addition I have moved the reading of
the Rx descriptor bits related to rx_ptype down so that they are actually
below the dma_rmb() call so that we are guaranteed that we don't have any
funky 64b on 32b calls causing any ordering issues.

Change-ID: I256e44a025d3c64a7224aaaec37c852bfcb1871b
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There exists a bug in which a 'perfect storm' can occur and cause
interrupts to fail to be correctly affinitized. This causes unexpected
behavior and has a substantial impact on performance when it happens.

The bug occurs if there is heavy traffic, any number of CPUs that have
an i40e interrupt are pegged at 100%, and the interrupt afffinity for
those CPUs is changed.  Instead of moving to the new CPU, the interrupt
continues to be polled while there is heavy traffic.

The bug is most readily realized as the driver is first brought up and
all interrupts start on CPU0. If there is heavy traffic and the
interrupt starts polling before the interrupt is affinitized, the
interrupt will be stuck on CPU0 until traffic stops. The bug, however,
can also be wrought out more simply by affinitizing all the interrupts
to a single CPU and then attempting to move any of those interrupts off
while there is heavy traffic.

This patch fixes the bug by registering for update notifications from
the kernel when the interrupt affinity changes. When that fires, we
cache the intended affinity mask. Then, while polling, if the cpu is
pegged at 100% and we failed to clean the rings, we check to make sure
we have the correct affinity and stop polling if we're firing on the
wrong CPU.  When the kernel successfully moves the interrupt, it will
start polling on the correct CPU. The performance impact is minimal
since the only time this section gets executed is when performance is
already compromised by the CPU.

Change-ID: I4410a880159b9dba1f8297aa72bef36dca34e830
Signed-off-by: NAlan Brady <alan.brady@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We cannot currently support SCTP in the hardware, and IPV4_FLOW is not used
anywhere by the software so we can go through and drop the functionality
related to these two flow types.

In addition we cannot support masking based on the protocol value so if the
user is expecting a value other than TCP or UDP we should simply return an
error rather then trying to allocate a filter for a rule that will only
partially match what the user requested.

Change-ID: I10d52bb97d8104d76255fe244551814ff9531a63
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We can reorder the busy wait loop at the start of the Flow Director
transmit function to reduce the overall code size while still retaining the
same functionality.  As such I am taking advantage of the opportunity to do
so.

Change-ID: I34c403ca001953c6ac9816e65d5305e73d869026
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In commit a75e8005 ("i40e: queue-specific settings for interrupt
moderation") the i40e driver gained support for setting interrupt
moderation values per queue. This patch adds support for this feature
to the i40evf driver as well. In addition, a few changes are made to
the i40e implementation to add function header documentation comments,
as well.

This behaves in a similar fashion to the implementation in i40e. Thus,
requesting the moderation value when no queue is provided will report
queue 0 value, while setting the value without a queue will set all
queues at once.

Change-ID: I1f310a57c8e6c84a8524c178d44d1b7a6d3a848e
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This  interface was only ever meant for debug only. Since it is not
supposed to be here we are removing it.

Change-ID: Id771a1e5e7d3e2b4b7f56591b61fb48c921e1d04
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In an effort to improve code readability I am splitting the Flow Director
filter configuration out into a separate function like we have done for the
standard xmit path.  The general idea is to provide a single block of code
that translates the flow specification into a proper Flow Director
descriptor.

Change-ID: Id355ad8030c4e6c72c57504fa09de60c976a8ffe
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a txring_txq function which allows us to convert a
i40e_ring/i40evf_ring to a netdev_tx_queue structure.  This way we
can avoid having to make a multi-line function call for all the spots
that need access to this.

Change-ID: Ic063b71d8b92ea406d2c32e798c8e2b02809d65b
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The Tx cleanup flow was incorrectly assuming it could check for the flow
director bits after it had unmapped the buffer.  However in this case it
results in us trying to free a raw_buf as though it is an sk_buff.

To fix this I am moving up the flag test for the FD_SB bit so that when
find a non-NULL skb or raw_buf value we then check the flag and use the
appropriate call to free the buffer.

Change-ID: I6284034ba1ea87c9922e56f6eb3181f7f09bddde
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some locations that disable ATR accidentally used the "full" disable by
disabling the flag in the standard flags field. This incorrectly forces
ATR off permanently instead of temporarily disabling it. In addition,
some code locations accidentally set the ATR flag enabled when they only
meant to clear the auto_disable_flags. This results in ignoring the
user's ethtool private flag settings.

Additionally, when disabling ATR via ethtool, we did not perform a flush
of the FD table. This results in the previously assigned ATR rules still
functioning which was not expected.

Cleanup all these areas so that automatic disable uses only the
auto_disable_flag. Fix the flush code so that we can trigger a flush
even when we've disabled ATR and SB support, as otherwise the flush
doesn't work. Fix ethtool setting to actually request a flush. Fix
NETIF_F_NTUPLE flag to only clear the auto_disable setting and not
enable the full feature.

Change-ID: Ib2486111f8031bd16943e9308757b276305c03b5
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The i40e driver was incorrectly assuming that we would always be pulling
no more than 1 descriptor from each fragment.  It is in fact possible for
us to end up with the case where 2 descriptors worth of data may be pulled
when a frame is larger than one of the pieces generated when aligning the
payload to either 4K or pieces smaller than 16K.

To adjust for this we just need to make certain to test all the way to the
end of the fragments as it is possible for us to span 2 descriptors in the
block before us so we need to guarantee that even the last 6 descriptors
have enough data to fill a full frame.

Change-ID: Ic2ecb4d6b745f447d334e66c14002152f50e2f99
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch refactors tail bump check.

Change-ID: Ide0e19171d67d90cb2b06b8dcd4fa791ae120160
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This initializer isn't needed because the variable is assigned right
away.

Change-ID: I6ce3edb3f4e0364db248a7a0bcc62ca95c01d941
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There are a couple of issues I found in i40e_rx_checksum while doing some
recent testing.  As a result I have found the Rx checksum logic is pretty
much broken and returning that the checksum is valid for tunnels in cases
where it is not.

First the inner types are not the correct values to use to test for if a
tunnel is present or not.  In addition the inner protocol types are not a
bitmask as such performing an OR of the values doesn't make sense.  I have
instead changed the code so that the inner protocol types are used to
determine if we report CHECKSUM_UNNECESSARY or not.  For anything that does
not end in UDP, TCP, or SCTP it doesn't make much sense to report a
checksum offload since it won't contain a checksum anyway.

This leaves us with the need to set the csum_level based on some value.
For that purpose I am using the tunnel_type field.  If the tunnel type is
GRENAT or greater then this means we have a GRE or UDP tunnel with an inner
header.  In the case of GRE or UDP we will have a possible checksum present
so for this reason it should be safe to set the csum_level to 1 to indicate
that we are reporting the state of the inner header.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for offloading IPXIP6 type packets that represent
either IPv4 or IPv6 encapsulated inside of an IPv6 outer IP header.  In
addition with this change we should also be able to support FOU
encapsulated traffic with outer IPv6 headers.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch defines two new GSO definitions SKB_GSO_IPXIP4 and
SKB_GSO_IPXIP6 along with corresponding NETIF_F_GSO_IPXIP4 and
NETIF_F_GSO_IPXIP6. These are used to described IP in IP
tunnel and what the outer protocol is. The inner protocol
can be deduced from other GSO types (e.g. SKB_GSO_TCPV4 and
SKB_GSO_TCPV6). The GSO types of SKB_GSO_IPIP and SKB_GSO_SIT
are removed (these are both instances of SKB_GSO_IPXIP4).
SKB_GSO_IPXIP6 will be used when support for GSO with IP
encapsulation over IPv6 is added.
Signed-off-by: NTom Herbert <tom@herbertland.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This logic is inverted. If the RXHASH flag is set, then we should go
ahead and call skb_set_hash.

Change-ID: Ib2e30356dced1d3e939c8061ab6ad5bd94197e7c
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This is part 1 of the Rx refactor series, just including
changes to i40e.

This refactor aligns the receive routine with the one in
ixgbe which was highly optimized.  This reduces the code
we have to maintain and allows for (hopefully) more readable
and maintainable RX hot path.

In order to do this:
- consolidate the receive path into a single function that doesn't
  use packet split but *does* use pages for Rx buffers.
- remove the old _1buf routine
- consolidate several routines into helper functions
- remove ethtool control over packet split

Change-ID: I5ca100721de65992aa0114f8b4bac844b84758e0
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As part of preparation for the rx-refactor, remove the
packet split receive routine and ancillary code.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Refactor the interpretation of a tunnel.  This removes
some code and lets us start using the hardware's parsing.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch makes it so that i40e and i40evf can use GSO_PARTIAL to support
segmentation for frames with checksums enabled in outer headers.  As a
result we can now send data over these types of tunnels at over 20Gb/s
versus the 12Gb/s that was previously possible on my system.

The advantage with the i40e parts is that this offload is mostly
transparent as the hardware still deals with the inner and/or outer IPv4
headers so the IP ID is still incrementing for both when this offload is
performed.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver was offloading the VLAN tag into the skb
any time there was a VLAN tag and the hardware stripping was
enabled.  Just check to make sure it's enabled before put_tag.

Change-Id: Ife95290c06edd9a616393b38679923938b382241
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Looking over the documentation it turns out enabling IPIP and SIT offloads
for i40e is pretty straightforward.  As such I decided to enable them with
this patch.  In my testing I am seeing an improvement of 8 to 10 Gb/s
for IPIP and SIT tunnels with this offload enabled.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch addresses a bug introduced based on my interpretation of the
XL710 datasheet.  Specifically section 8.4.1 states that "A single transmit
packet may span up to 8 buffers (up to 8 data descriptors per packet
including both the header and payload buffers)."  It then later goes on to
say that each segment for a TSO obeys the previous rule, however it then
refers to TSO header and the segment payload buffers.

I believe the actual limit for fragments with TSO and a skbuff that has
payload data in the header portion of the buffer is actually only 7
fragments as the skb->data portion counts as 2 buffers, one for the TSO
header, and one for a segment payload buffer.

Fixes: 2d37490b ("i40e/i40evf: Rewrite logic for 8 descriptor per packet check")
Reported-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As it turns out, calling into other files from hot path hurts
performance a lot.  In this case the majority of the time we
call "check FCoE" and the packet is *not* FCoE, but this call
was taking 5% of our total cycles spent on receive.

Change-ID: I080552c26e7060bc7b78504dc2763f6f0b3d8c76
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some of the tx_ring arguments can be deleted since they are not used.

Change-ID: I99275b0f191d7f63ec2f05061919904940c36f31
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A local variable could move down inside the context where it is used.

Change-ID: I9caba9e1eacf921037077f2665cbce83fd8e95d6
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

With IPv4 and IPv6 now using the same format for checksums based on the
length of the frame we need to update the i40e and i40evf drivers so that
they correctly account for lengths greater than or equal to 64K.

With this patch the driver should now correctly update checksums for frames
up to 16776960 in length which should be more than large enough for all
possible TSO frames in the near future.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Simple cast to fix a sparse warning.

Fixes: commit 5453205c ("i40e/i40evf: Enable support for
SKB_GSO_UDP_TUNNEL_CSUM")
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch enables bulk Tx clean for skbs.  In order to enable it we need
to pass the napi_budget value as that is used to determine if we are truly
running in NAPI mode or if we are simply calling the routine from netpoll
with a budget of 0.  In order to avoid adding too many more variables I
thought it best to pass the VSI directly in a fashion similar to what we do
on igb and ixgbe with the q_vector.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In the polling routines for i40e and i40evf we were using bitwise operators
to avoid the side effects of the logical operators, specifically the fact
that if the first case is true with "||" we skip the second case, or if it
is false with "&&" we skip the second case.  This fixes an earlier patch
that converted the bitwise operators over to the logical operators and
instead replaces the entire thing with just an if statement since it should
be more readable what we are trying to do this way.

Fixes: 1a36d7fa ("i40e/i40evf: use logical operators, not bitwise")
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>