It's supposed to be impossible for TPA to give us anything else
than IPv4 or IPv6 here. But in case there is a way to reach this error
by some strange received frames, we don't want to flood the kernel log.
WARN_ONCE is better for this purpose.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc_pages() already prints a warning when it fails. No need to emit
another message. Certainly not at KERN_ERR level, because it is no big
deal if this GFP_ATOMIC allocation fails occasionally.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 46e8a249423ff "bnx2x: Add FW 7.13.1.0" added said .bin FW to
linux-firmware; This patch incorporates the FW in the bnx2x driver.

This introduces 2 fixes/enhancements:
 - In some management protocols there are outer-vlan configurations
that can be dynamically changed while device is running. This fixes
some corner cases where such a change did not take effect.

 - Prevent VFs from sending MAC control frames; FW would treat a VF
sending such a packet as malicious and block any further communication
done by the VF.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Today, port statistics are being presented when using `ethool -S' only
for single-function devices, but there are some port statistics which are
crucial for analyzing bottle-necks. E.g., HW Rx discards due to lack of
buffer space [when device isn't handling ingress traffic fast enough].

Judging the pros and cons, it was decided that in-order to better support
automatic dump-gathering tools, bnx2x should no longer hide those stats.
This leaves only VFs lacking the port statistics.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver already has an internal counter for number of times a given queue
had to be stopped due to Tx ring exhaustion.
This add the counter to the statistics presented by driver, e.g., by using
`ethtool -S'.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commmit ac7eccd4 "bnx2x: track vxlan port count" contains a bug -
Instead of achieving the required goal, vxlan configuration would not
be removed since we're decrementing the port instead of the counter.

CC: Jiri Benc <jbenc@redhat.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NAPI drivers no longer need to observe a particular protocol
to benefit from busy polling (CONFIG_NET_RX_BUSY_POLL=y)

napi_hash_add() and napi_hash_del() are automatically called
from core networking stack, respectively from
netif_napi_add() and netif_napi_del()

This patch depends on free_netdev() and netif_napi_del() being
called from process context, which seems to be the norm.

Drivers might still prefer to call napi_hash_del() on their
own, since they might combine all the rcu grace periods into
a single one, knowing their NAPI structures lifetime, while
core networking stack has no idea of a possible combining.

Once this patch proves to not bring serious regressions,
we will cleanup drivers to either remove napi_hash_del()
or provide appropriate rcu grace periods combining.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We would like to automatically provide busy polling support
to all NAPI drivers, without them having to implement anything.

skb_mark_napi_id() can be called from napi_gro_receive() and
napi_get_frags().

Few drivers are still calling skb_mark_napi_id() because
they use netif_receive_skb(). They should eventually call
napi_gro_receive() instead. I will leave this to drivers
maintainers.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Switch to native NAPI polling, as this reduces overhead and complexity.

Normal path is faster, since one cmpxchg() is not anymore requested,
and busy polling with the NAPI polling has same performance.

Tested:
lpk50:~# cat /proc/sys/net/core/busy_read
70
lpk50:~# nstat >/dev/null;./netperf -H lpk55 -t TCP_RR;nstat
MIGRATED TCP REQUEST/RESPONSE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to lpk55.prod.google.com () port 0 AF_INET : first burst 0
Local /Remote
Socket Size   Request  Resp.   Elapsed  Trans.
Send   Recv   Size     Size    Time     Rate
bytes  Bytes  bytes    bytes   secs.    per sec

16384  87380  1        1       10.00    40095.07
16384  87380
IpInReceives                    401062             0.0
IpInDelivers                    401062             0.0
IpOutRequests                   401079             0.0
TcpActiveOpens                  7                  0.0
TcpPassiveOpens                 3                  0.0
TcpAttemptFails                 3                  0.0
TcpEstabResets                  5                  0.0
TcpInSegs                       401036             0.0
TcpOutSegs                      401052             0.0
TcpOutRsts                      38                 0.0
UdpInDatagrams                  26                 0.0
UdpOutDatagrams                 27                 0.0
Ip6OutNoRoutes                  1                  0.0
TcpExtDelayedACKs               1                  0.0
TcpExtTCPPrequeued              98                 0.0
TcpExtTCPDirectCopyFromPrequeue 98                 0.0
TcpExtTCPHPHits                 4                  0.0
TcpExtTCPHPHitsToUser           98                 0.0
TcpExtTCPPureAcks               5                  0.0
TcpExtTCPHPAcks                 101                0.0
TcpExtTCPAbortOnData            6                  0.0
TcpExtBusyPollRxPackets         400832             0.0
TcpExtTCPOrigDataSent           400983             0.0
IpExtInOctets                   21273867           0.0
IpExtOutOctets                  21261254           0.0
IpExtInNoECTPkts                401064             0.0
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 05cc5a39 "bnx2x: add vlan filtering offload" introduced
a regression in regard for vlans for 57710, 57711 adapters -
Loading 8021q module on a machine with such an adapter would cause
a null pointer dereference, as the driver mistakenly publishes it
has capabilities for vlan CTAG filtering.
Reported-by: NOtto Sabart <osabart@redhat.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mm, page_alloc: distinguish between being unable to sleep, unwilling to sleep and avoiding waking kswapd

__GFP_WAIT has been used to identify atomic context in callers that hold
spinlocks or are in interrupts.  They are expected to be high priority and
have access one of two watermarks lower than "min" which can be referred
to as the "atomic reserve".  __GFP_HIGH users get access to the first
lower watermark and can be called the "high priority reserve".

Over time, callers had a requirement to not block when fallback options
were available.  Some have abused __GFP_WAIT leading to a situation where
an optimisitic allocation with a fallback option can access atomic
reserves.

This patch uses __GFP_ATOMIC to identify callers that are truely atomic,
cannot sleep and have no alternative.  High priority users continue to use
__GFP_HIGH.  __GFP_DIRECT_RECLAIM identifies callers that can sleep and
are willing to enter direct reclaim.  __GFP_KSWAPD_RECLAIM to identify
callers that want to wake kswapd for background reclaim.  __GFP_WAIT is
redefined as a caller that is willing to enter direct reclaim and wake
kswapd for background reclaim.

This patch then converts a number of sites

o __GFP_ATOMIC is used by callers that are high priority and have memory
  pools for those requests. GFP_ATOMIC uses this flag.

o Callers that have a limited mempool to guarantee forward progress clear
  __GFP_DIRECT_RECLAIM but keep __GFP_KSWAPD_RECLAIM. bio allocations fall
  into this category where kswapd will still be woken but atomic reserves
  are not used as there is a one-entry mempool to guarantee progress.

o Callers that are checking if they are non-blocking should use the
  helper gfpflags_allow_blocking() where possible. This is because
  checking for __GFP_WAIT as was done historically now can trigger false
  positives. Some exceptions like dm-crypt.c exist where the code intent
  is clearer if __GFP_DIRECT_RECLAIM is used instead of the helper due to
  flag manipulations.

o Callers that built their own GFP flags instead of starting with GFP_KERNEL
  and friends now also need to specify __GFP_KSWAPD_RECLAIM.

The first key hazard to watch out for is callers that removed __GFP_WAIT
and was depending on access to atomic reserves for inconspicuous reasons.
In some cases it may be appropriate for them to use __GFP_HIGH.

The second key hazard is callers that assembled their own combination of
GFP flags instead of starting with something like GFP_KERNEL.  They may
now wish to specify __GFP_KSWAPD_RECLAIM.  It's almost certainly harmless
if it's missed in most cases as other activity will wake kswapd.
Signed-off-by: NMel Gorman <mgorman@techsingularity.net>
Acked-by: NVlastimil Babka <vbabka@suse.cz>
Acked-by: NMichal Hocko <mhocko@suse.com>
Acked-by: NJohannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().

v2: removed unused variable
v3: removed another unused variable
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Configuring 4-tuple RSS hsahing for UDP
[E.g., by using `ethtool -N <interface> rx-flow-hash udp4 sdfn']
on a 57710/57711 adapter would cause it to assert as HW does not
support such a configuration.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After a good amount of debugging, I found bnx2x was byte swaping
the 40 bytes of rss_key.

If we byte swap the key, then bnx2x generates hashes matching
MSDN specs as documented in (Verifying the RSS Hash Calculation)

https://msdn.microsoft.com/en-us/library/windows/hardware/ff571021%
28v=vs.85%29.aspx

It is mostly a non issue, unless we want to mix different NIC
in a host, and want consistent hashing among all of them, ie
if they all use the boot time generated rss key, or if some application
is choosing specific tuple(s) so that incoming traffic lands into known
rx queue(s).
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The callback for adding vxlan port can be called with the same port for
both IPv4 and IPv6. Do not disable the offloading when the same port for
both protocols is added and later one of them removed.
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit c48f350f "bnx2x: Add MFW dump support" added the
bnx2x_update_mfw_dump() function that reads the current time and stores
it in a 32-bit field that gets passed into a buffer in a fixed format.

This is potentially broken when the epoch overflows in 2038, and
otherwise overflows in 2106. As we're trying to avoid uses of
struct timeval for this reason, I noticed the addition of this
function, and tried to rewrite it in a way that is more explicit
about the overflow and that will keep working once we deprecate
struct timeval.

I assume that it is not possible to change the ABI any more, otherwise
we should try to use a 64-bit field for the seconds right away.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Yuval Mintz <Yuval.Mintz@qlogic.com>
Cc: Ariel Elior <Ariel.Elior@qlogic.com>
Acked-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support for 3 new PCI device combinations -
1077:16a1, 1077:16a4 and 1077:16ad.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit f34fa14c ("bnx2x: Add vxlan RSS support") has introduced an
endianity issue when passing the vxlan UDP port to the HW.

Reported-by: <fengguang.wu@intel.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Latest FW submission added some vxlan offload capabilities to our device.
This patch adds the ability to connect to the vxlan NDOs and configure
the UDP port associated with it in the HW.

The device would now be capable of performing RSS according to the
inner headers of the vxlan packets.
Signed-off-by: NRajesh Borundia <Rajesh.Borundia@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Management firmware tells driver in case bandwidth configuration for
a specific function exists, but [regretably] the same field has different
meanings depending on the multi-function mode - it can either be
a percentile value or an actual speed.

For newer multi-function modes current logic is incorrect -
driver understands values as actual speeds instead of percentages,
causing the resulting chip configuration to be incorrect.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Writing each 4Kb page into flash might take up-to ~100 miliseconds,
during which time management firmware cannot acces the nvram for its
own uses.

Firmware upgrade utility use the ethtool API to burn new flash images
for the device via the ethtool API, doing so by writing several page-worth
of data on each command. Such action might create problems for the
management firmware, as the nvram might not be accessible for a long time.

This patch changes the write implementation, releasing the nvram lock on
the completion of each page, allowing the management firmware time to
claim it and perform its own required actions.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On error flows its possible to free an SKB even if it was not allocated.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 230d00eb ("bnx2x: new Multi-function mode - BD") adds support
for the new mode in bnx2x. This expands this support by implementing
APIs required by our storage drivers to support that mode.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 05cc5a39 ("bnx2x: add vlan filtering offload") has introduced
an incorrect logic for checking whether pvid should be configured for
a vf, causing the hypervisor driver to send unneeded ramrods for all of
the vfs each time a pvid has changed.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 05cc5a39 ("bnx2x: add vlan filtering offload") has broken
compilation when CONFIG_BNX2X_SRIOV is not set.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current driver always uses vlan-promisc mode, i.e., it receives both
tagged and untagged traffic and lets the network stack drop packets
tagged with unrequested vlan tags.

This patch implements vlan-filtering offload in the driver -
Unless explicitly configured to promisc mode, only untagged packets or
packets tagged with requested vlans would reach the Rx flow.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Devices with up-to-date management FW will be able to store register dumps
on their persistent storage - in case management FW identifies a fatal
error it would gather and store such dumps, which could later be retrieved
using specific debug tools.

This patch adds the necessary part in the driver in order to make the
feature operational, as well as update users [under debug] during load
in case their device contains a dump of a previous crash.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support to a new multi-function mode, enabling driver to
initialize such devices and correctly interacting with management FW
for fully utilizing their features.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support to a new copper phy.
Signed-off-by: NYaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2x still appears as a Broadcom driver even though the devices it
utilizes belong to Qlogic for more than a year.

This patch changes the various headers and the device strings to indicate
the correct ownership of the device.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This moves bnx2x into using 7.12.30 FW. Said firmware fixes the following:

 - Packets from a VF with pvid configured which were sent with a
   different vlan were transmitted instead of being discarded.

 - FCoE traffic might not recover after a failue while there's traffic
   to another function.

In addition, this FW opens the door for the driver to implement several
new features; Specifically, this enhances the device's support for
encapsulated packets and will allow vxlan/geneve offloads to be added in
the future, as well as vlan filtering offload.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CC: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

With CONFIG_DMA_API_DEBUG=y bnx2x triggers the error "DMA-API: device
driver frees DMA memory with wrong function".
On archs where PAGE_SIZE > SGE_PAGE_SIZE it also triggers "DMA-API:
device driver frees DMA memory with different size".

Fix this by making the mapping and unmapping symmetric:
 - Do not map the whole pool page at once. Instead map the
   SGE_PAGE_SIZE-sized pieces individually, so they can be unmapped in
   the same manner.
 - What's mapped using dma_map_page() must be unmapped using
   dma_unmap_page().

Tested on ppc64.

Fixes: 4cace675 ("bnx2x: Alloc 4k fragment for each rx ring buffer element")
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Michel reported following lockdep splat

[   44.718117] INFO: trying to register non-static key.
[   44.723081] the code is fine but needs lockdep annotation.
[   44.728559] turning off the locking correctness validator.
[   44.734036] CPU: 8 PID: 5483 Comm: ethtool Not tainted 4.1.0
[   44.770289] Call Trace:
[   44.772741]  [<ffffffff816eb1cd>] dump_stack+0x4c/0x65
[   44.777879]  [<ffffffff8111d921>] ? console_unlock+0x1f1/0x510
[   44.783708]  [<ffffffff811121f5>] __lock_acquire+0x1d05/0x1f10
[   44.789538]  [<ffffffff8111370a>] ? mark_held_locks+0x6a/0x90
[   44.795276]  [<ffffffff81113835>] ? trace_hardirqs_on_caller+0x105/0x1d0
[   44.801967]  [<ffffffff8111390d>] ? trace_hardirqs_on+0xd/0x10
[   44.807793]  [<ffffffff811330fa>] ? hrtimer_try_to_cancel+0x4a/0x250
[   44.814142]  [<ffffffff81112ba6>] lock_acquire+0xb6/0x290
[   44.819537]  [<ffffffff810d6675>] ? flush_work+0x5/0x280
[   44.824844]  [<ffffffff810d66ad>] flush_work+0x3d/0x280
[   44.830061]  [<ffffffff810d6675>] ? flush_work+0x5/0x280
[   44.835366]  [<ffffffff816f3c43>] ? schedule_hrtimeout_range+0x13/0x20
[   44.841889]  [<ffffffff8112ec9b>] ? usleep_range+0x4b/0x50
[   44.847365]  [<ffffffff8111370a>] ? mark_held_locks+0x6a/0x90
[   44.853102]  [<ffffffff810d8585>] ? __cancel_work_timer+0x105/0x1c0
[   44.859359]  [<ffffffff81113835>] ? trace_hardirqs_on_caller+0x105/0x1d0
[   44.866045]  [<ffffffff810d851f>] __cancel_work_timer+0x9f/0x1c0
[   44.872048]  [<ffffffffa0010982>] ? bnx2x_func_stop+0x42/0x90 [bnx2x]
[   44.878481]  [<ffffffff810d8670>] cancel_work_sync+0x10/0x20
[   44.884134]  [<ffffffffa00259e5>] bnx2x_chip_cleanup+0x245/0x730 [bnx2x]
[   44.890829]  [<ffffffff8110ce02>] ? up+0x32/0x50
[   44.895439]  [<ffffffff811306b5>] ? del_timer_sync+0x5/0xd0
[   44.901005]  [<ffffffffa005596d>] bnx2x_nic_unload+0x20d/0x8e0 [bnx2x]
[   44.907527]  [<ffffffff811f1aef>] ? might_fault+0x5f/0xb0
[   44.912921]  [<ffffffffa005851c>] bnx2x_reload_if_running+0x2c/0x50 [bnx2x]
[   44.919879]  [<ffffffffa005a3c5>] bnx2x_set_ringparam+0x2b5/0x460 [bnx2x]
[   44.926664]  [<ffffffff815d498b>] dev_ethtool+0x55b/0x1c40
[   44.932148]  [<ffffffff815dfdc7>] ? rtnl_lock+0x17/0x20
[   44.937364]  [<ffffffff815e7f8b>] dev_ioctl+0x17b/0x630
[   44.942582]  [<ffffffff815abf8d>] sock_do_ioctl+0x5d/0x70
[   44.947972]  [<ffffffff815ac013>] sock_ioctl+0x73/0x280
[   44.953192]  [<ffffffff8124c1c8>] do_vfs_ioctl+0x88/0x5b0
[   44.958587]  [<ffffffff8110d0b3>] ? up_read+0x23/0x40
[   44.963631]  [<ffffffff812584cc>] ? __fget_light+0x6c/0xa0
[   44.969105]  [<ffffffff8124c781>] SyS_ioctl+0x91/0xb0
[   44.974149]  [<ffffffff816f4dd7>] system_call_fastpath+0x12/0x6f

As bnx2x_init_ptp() is only called if bp->flags contains PTP_SUPPORTED,
we also need to guard bnx2x_stop_ptp() with same condition, otherwise
ptp_task workqueue is not initialized and kernel barfs on
cancel_work_sync()

Fixes: eeed018c ("bnx2x: Add timestamping and PTP hardware clock support")
Reported-by: NMichel Lespinasse <walken@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Michal Kalderon <Michal.Kalderon@qlogic.com>
Cc: Ariel Elior <Ariel.Elior@qlogic.com>
Cc: Yuval Mintz <Yuval.Mintz@qlogic.com>
Cc: David Decotigny <decot@google.com>
Acked-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to FW constraints, driver must make sure that transmitted SKBs will
not be too fragmented, or in the case that they are - that each 'window'
of fragments passed to the FW would contain at least an mss worth of data.

For encapsultaed packets the calculation is wrong, since it ignores the
inner headers in the calculation of the headers' length.
This could lead to a FW assertion in case of a too-fragmented encapsulated
packet.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During an error flow when trying to access the nvram the driver doesn't
release the hw lock it acquired.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since driver statistics flow access MACs and those might reset during
link re-configurations, when we're about to change link properties we
have to make sure that statistics are not operational.
Statisics would be re-enabled [i.e., gathering of statistics would
re-commence] once physical link is achieved again.

Since driver employs a link-flap avoidance scheme, there are scenarios
where driver will receive no indication that the new link is up, and
as a result the statistics would not be re-enabled.

Preventing LFA from working in such cases would guarantee that we'll
always receive such indications and thus will fix statistics gathering.
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

20g-capable devices are not configured properly for self-test, using
10g as their speed which cause the link indication to remain down and
fail the internal loopback test.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's a bug in today's driver where VF requests to add/remove MAC filters
always reach the Hypervisor as add requests.
This prevents the VF from changing its MAC address, as it cannot remove the
previously configured MAC and runs out of MAC credits.
Signed-off-by: NShahed Shaikh <Shahed.Shaikh@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>