Rename this function to the more appropriate iwl_pcie_check_hw_rf_kill()
since it's only a function in the pcie code and cannot be called from
any other place.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The return status check of iwl_pcie_gen2_build_amsdu
was buggy. Fix it.

Fixes: 6ffe5de3 ("iwlwifi: pcie: add AMSDU to gen2")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Apart from DVM, all firmware uses the same base API, and there's
code outside iwlmvm that needs to interact with it. Reflect this
in the source better and reorganize the firmware API to a new
fw/api/ directory.

While at it, split the already pretty large fw-api.h file into a
number of smaller files, going from almost 3k lines in there to
a maximum number of lines less than 1k.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The newest devices need a longer time to reset because of
their more complex hardware. Wait 5ms after device reset.
Consolidate all the places that reset the device in the
PCIe transport to avoid future bugs.

While at it, unify the flow to use set_bit instead of full
write as requested by the hardware designers.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

iwl_pcie_apm_init can fail so make sure that the caller
takes the status into account.
Also, ensure that the error that iwl_pcie_apm_init can emit
will appear in the kernel log by default.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When going into suspend, the HW configuration for MSI-X will
likely be lost. As a consequence, after waking up, all IRQ
causes will be mapped to interrupt 0, and as a consequence we
don't notice the interrupt because in most cases this is an
interrupt for a queue, and getting it doesn't read the other
cause registers.

Fixes: 2e5d4a8f ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We have tracing for both pre-ICT and ICT interrupts, including all
the data read there. Extend the tracing to MSI-X interrupts.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

There's a lot of mvm code that really should be more generic
and part of the iwlwifi module. Start by making a place to
keep such code - in the new "fw" subdirectory - and already
move the firmware related header files there.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This appears to happen in some cases, like when iwlmvm is unloaded and
loaded again without also unloading iwlwifi. Warn in this case and free
the paging data to be able to continue without causing corruption and
kernel crashes due to it (otherwise, paging data is overwritten, but
dram->paging_cnt gets to be twice as big as it should be, and then an
eventual free will crash.)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

By setting the pointers to NULL at the end, these functions
are made idempotent.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Where possible (all except for "11n_disable", which isn't valid in C)
rename the internal names for module parameters to be the same as the
externally visible names, to aid finding their use etc.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Print the queue for the existing debug message and add a new
debug message indicating where the RB ended.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Print out both queue IDs to be able to see what went wrong.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add twelve new PCI IDs for the 9560 series.
Signed-off-by: NTzipi Peres <tzipi.peres@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add a new config struct for the new a000 2ax series and add
the five PCI ID for it.
Signed-off-by: NTzipi Peres <tzipi.peres@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

A hardware issue on 9000 series devices sometimes causes RF-kill
interrupts to not be propagated to the host properly if ASPM is
enabled. Work around this by setting the right hardware bit to
allow it to interrupt the host for this reason (rfkill).
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Due to a hardware issue, certain power saving had to be
disabled. However, this issue was fixed in B-step, so the
workaround only needs to apply to A-step.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In some platforms, having the device enabled with certain radio
frontends causes the platform to not be able to resume properly
from suspend, regardless of the wakeup cause. This was traced to
a hardware issue with the integrated 9000-series A-step variant.
Set the right hardware bit to disable the problematic state.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When the firmware crashes, the transmit queues can't make
any progress. This is why we stop the counter that monitor
the transmit queues' activity.
The call that notifies the error to the op_mode may take
a bit of time, so stop the timer of the transmit queues
earlier.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The driver prints "L1 Enabled - LTR Enabled" all the time as dev_info,
which is just useless noise in most cases.  Convert this to
IWL_DEBUG_POWER() so we don't pollute the log unnecessarily but still
can get this info on demand.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Nothing ever checks the return value of iwl_pcie_apm_stop_master(),
so there's no point in it having one - make it return void.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In case we need to move the scheduler write pointer by
steps of 0x40, 0x80 or 0xc0, the scheduler gets stuck.
This leads to hardware error interrupts with status:
0x5A5A5A5A or alike.

In order to work around this, detect in the transport
layer that we are going to hit this case and tell iwlmvm
to increment the sequence number of the packets. This
allows to keep the requirement that the WiFi sequence
number is in sync with the index in the scheduler Tx queue
and it also allows to avoid the problematic sequence.
This means that from time to time, we will start a queue
from ssn + 1, but that shouldn't be a problem since we
don't switch to new queues for AMPDU now that we have
DQA which allows to keep the same queue while toggling
the AMPDU state.

This bug has been fixed on 9000 devices and up.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When we started using threaded irqs, all the opmode calls were changed
to be called with local_bh disabled.  The reason for this was it was
that mac80211 needs that.  When we are handling FW errors, mac80211 is
not involved, so we don't need it.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When the command name is printed on command completion, the wrong
group is used, leading to the wrong name being printed. Fix this
by using the group ID without inappropriately mangling it through
iwl_cmd_groupid() - it's already a u8. Also, while at it, use it
from the same place as the command ID, everything else is just
confusing.

Fixes: ab02165c ("iwlwifi: add wide firmware command infrastructure for TX")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When sending non-linear SKBs that should be included in the regular
TX tracing completely (and not be pushed into the tx_data tracing),
the (tracing) code didn't correctly take the fact that they were
non-linear into account and added only the skb head portion.

This probably never really triggered, since those frames we want
traced fully are most likely linear anyway, but the code gets easier
to understand and we lose an argument to the tracing function, so
overall fixing this is better.

Fixes: 206eea78 ("iwlwifi: pcie: support frag SKBs")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

There's no need to calculate the data_len outside of the tracepoint,
since it's always skb->len - hdr_len, which are both available inside.
Simplify the callers and move the calculation in.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Use kstrtou32_from_user() in debugfs instead of open-coding it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We don't actually care about the value at all, just making sure
that we can successfully parse a single integer value, but that's
entirely pointless - remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When toggling the RF-kill pin quickly in succession, the driver can
get rather confused because it might be in the process of shutting
down, expecting all commands to go through quickly due to rfkill,
but the transport already thinks the device is accessible again,
even though it previously shut it down. This leads to bugs, and I
even observed a kernel panic.

Avoid this by making the PCIe code only report that the radio is
enabled again after the higher layers actually decided to shut it
off.

This also pulls out this common RF-kill checking code into a common
function called by both transport generations and also moves it to
the direct method - in the internal helper we don't really care
about the RF-kill status anymore since we won't report it up until
the stop anyway.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In order to debug "hardware" RF-kill flows, add a low-level hook to
allow changing the "hardware" RF-kill from debugfs.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

There's no point in duplicating exactly the same code here
for legacy and MSI-X interrupts, so pull it out into a new
function to call in both places.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Letting the preprocessor/compiler generate the shift/mask by itself
is a win for readability, so use bitfield.h for some registers.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The queue ID should never be 512 either, so correct the check
to be >= instead of just >.

Fixes: 310181ec ("iwlwifi: move to TVQM mode")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.

An spatch similar to the one for skb_put_zero() converts many
of the places using it:

    @@
    identifier p, p2;
    expression len, skb, data;
    type t, t2;
    @@
    (
    -p = skb_put(skb, len);
    +p = skb_put_data(skb, data, len);
    |
    -p = (t)skb_put(skb, len);
    +p = skb_put_data(skb, data, len);
    )
    (
    p2 = (t2)p;
    -memcpy(p2, data, len);
    |
    -memcpy(p, data, len);
    )

    @@
    type t, t2;
    identifier p, p2;
    expression skb, data;
    @@
    t *p;
    ...
    (
    -p = skb_put(skb, sizeof(t));
    +p = skb_put_data(skb, data, sizeof(t));
    |
    -p = (t *)skb_put(skb, sizeof(t));
    +p = skb_put_data(skb, data, sizeof(t));
    )
    (
    p2 = (t2)p;
    -memcpy(p2, data, sizeof(*p));
    |
    -memcpy(p, data, sizeof(*p));
    )

    @@
    expression skb, len, data;
    @@
    -memcpy(skb_put(skb, len), data, len);
    +skb_put_data(skb, data, len);

(again, manually post-processed to retain some comments)
Reviewed-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

FH in A000 HW are placed in a different location,
and need to be read as prph, rather than direct.
Support A000 dumping as well as legacy.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add two new device families to differentiate them from 8000.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This is essentially the same code as gen1, except that it uses
gen2 functions and SW checksum is not included.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Sending host command with CMD_WANT_SKB flag demands the release of the
response buffer with iwl_free_resp function.
The patch adds the memory release in all the relevant places
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We only need to handle d0i3 entry and exit during suspend resume if
system_pm is set to IWL_PLAT_PM_MODE_D0I3, otherwise d0i3 entry
failures will cause suspend to fail.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=194791Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Now that we have 512 queues, add a wait for single TX
queue to gen2.
This replaces gen1 wait_tx_queues_empty, which was limited
to 32 queues.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>