5784 and 5764 devices lock up when the link speed is 10Mbps, the CPMU
link speed mode is enabled, and the MAC clock is running at 1.5Mhz.  The
fix is to run the MAC clock at faster speeds.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch corrects a bug where the ENABLE_APE flag was tested against
the wrong flag variable.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

5784 and 5764 devices fail to link / pass traffic after one load /
unload cycle.  This happens because of a hardware bug in the new CPMU.
During normal operation, the MAC depends on the PHY clock being
available.  When the PHY is powered down, the clock the MAC depends on
is disabled.  The fix is to switch the MAC clock to an alternate source
before powering down the PHY, and to restore the MAC clock to the PHY
source upon device resume.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When 5761 devices boot the machine using PXEboot, PXE leaves the device
active when it terminates.  The tg3 driver has code to detect this
condition and resets the device during initialization.  On 5761 devices,
device resets involve sending a driver state update message to the APE
on the 5761.  However, during this initialization stage, communications
to the APE registers have not yet been set up.  The driver then
dereferences a NULL pointer and crashes the machine.  The fix is to move
the APE register access setup earlier in the initialization code to
cover this condition.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When I removed net-modules.txt because it only contained ancient
information I missed that many Kconfig entries pointed to this ancient
information.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

...and fix a couple of bugs in the NBD, CIFS and OCFS2 socket handlers.

Looking at the sock->op->shutdown() handlers, it looks as if all of them
take a SHUT_RD/SHUT_WR/SHUT_RDWR argument instead of the
RCV_SHUTDOWN/SEND_SHUTDOWN arguments.
Add a helper, and then define the SHUT_* enum to ensure that kernel users
of shutdown() don't get confused.
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>
Acked-by: NMark Fasheh <mark.fasheh@oracle.com>
Acked-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit bea3348e (the NAPI changes) made sungem unconditionally enable
NAPI when resuming and unconditionally disable when suspending, this,
however, makes napi_disable() hang when suspending when the interface
was taken down before suspend because taking the interface down also
disables NAPI. This patch makes touching the napi struct in
suspend/resume code paths depend on having the interface up, thereby
fixing the hang on suspend.

The patch also moves the napi_disable() in gem_close() under the lock so
that the NAPI state is always modified atomically together with the
"opened" variable.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fix sparse warnings "Using plain integer as NULL pointer"
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The virtio descriptor rings of size N-1 were nicely set up to be
aligned to an N-byte boundary.  But as Anthony Liguori points out, the
free-running indices used by virtio require that the sizes be a power
of 2, otherwise we get problems on wrap (demonstrated with lguest).

So we replace the clever "2^n-1" scheme with a simple "align to page
boundary" scheme: this means that all virtio rings take at least two
pages, but it's safer than guessing cache alignment.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

The more_used() function compares the vq->vring.used->idx with last_used_idx.
Since vq->vring.used->idx is a 16-bit integer, and last_used_idx is an
unsigned int, this results in unpredictable behavior when vq->vring.used->idx
wraps around.

This patch corrects this by changing last_used_idx to the correct type.
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

This fixes OOPS in network driver when CONFIG_DEBUG_SG=y.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

This fixes the lowlevel bus access routines for
PCMCIA based devices.

There are still a few issues with register access sideeffects after
this patch. This will be addressed in a later patch.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Prior to this patch, iwlwifi would always use the first
registered rate control algorithm which, depending on system
setup, could be anything. After the mac80211 patch to make
the simple algorithm built-in, it would always be simple.

This has always been a bug in iwlwifi.

This fixes it by requesting that mac80211 selects the right
rate control algorithm.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ssb must init after PCI but before the ssb drivers.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Cc: Christian Casteyde <casteyde.christian@free.fr>
Fixes-bug: #9219
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add documentation in Kconfig help about the move of /proc/acpi/battery
to /sys/class/power_supply when selecting ACPI_PROCFS.  This will impact
a lot of users and should be documented.
Signed-off-by: NJerome Pinot <ngc891@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NRolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Oops.

The current code does not like being given an u16 with the highest
bit set as an argument to mdio_write. Let's enforce a correct range of
values for both the register address and value (resp. 5 and 16 bits).

The callers are currently left as-is.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>

RTL_GIGA_MAC_VER_17 breaks as well.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>

Found a couple of more chips in the latest version of the vendor driver.
They are minor variations on existing chips.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ax88796: add superh to kconfig dependencies

This patch adds sh architecture support to the ax88796 kconfig.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Luckily, this wasn't reported or reproduced. The logical operation for
setting duplex had wrong grouping.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The link state machine requires access to some resources that
are shared with the iSCSI function on the chip.  (See iSCSI
driver at drivers/scsi/qla4xxx)  If the interface is being
up/downed at a rapid pace this driver may need to sleep
waiting to get access to the common resources. For this we
are moving the state machine to run as a work thread.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make sure we don't feed packets with bad CRC up the network stack,
and discount the packet length as reported from the MAC for the CRC
field.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Don't use the "replace source address with local MAC address" bits, since
it causes problems on some variations of the hardware due to an erratum.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The standard validate_addr handler refuses to accept the all zeroes address
as valid.  However, it's common historical practice for the bonding
master to be configured up prior to having any slaves, at which time the
master will have a MAC address of all zeroes.

Resolved by setting the dev->validate_addr to NULL.  The master still can't
end up with an invalid address, as the set_mac_address function tests
for validity.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

	Looks like I incorrectly merged one of the rtnl lock changes,
so that one function, bonding_show_active_slave, held rtnl but didn't
release it, and another, bonding_store_active_slave, never held rtnl but
did release it.

	Fixed so the first function doesn't mess with rtnl, and the
second correctly acquires and releases rtnl.

	Bug reported by Moni Shoua <monis@voltaire.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Netpoll will only work on port 0 because of the restrictive
relationship between NAPI and netpoll.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix dependencies for built-in b43.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix a sparse warning about a nonstatic function.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

PCMCIA needs an additional step to request the IRQ.

No need to add code to release the IRQ here, as that's done
automatically in pcmcia_disable_device().
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix an IRQ race condition in b43legacy. If we call
b43legacy_wireless_core_stop(), it will set the status of the device to
INITIALIZED and the IRQ handler won't care any longer about IRQs, thus the
kernel will disable the IRQ if it's shared (unless we boot it with the
'irqpoll' option). So we must disable IRQs before changing the device
status.
Signed-off-by: NStefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix an IRQ race condition in b43. If we call b43_stop_wireless_core(), it
will set the status of the device to INITIALIZED and the IRQ handler won't
care any longer about IRQs, thus the kernel will disable the IRQ if it's
shared (unless we boot it with the 'irqpoll' option). So we must disable
IRQs before changing the device status.
Signed-off-by: NStefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix possible buffer overrun.

The patch to b43 by Michael Buesch <mb@bu3sch.de> has been ported to
b43legacy.
Signed-off-by: NStefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The rfkill subsystem doesn't like code like that
rfkill_allocate();
rfkill_register();
rfkill_unregister();
rfkill_register(); /* <- This will crash */

This sequence happens with
modprobe b43
ifconfig wlanX up
ifconfig wlanX down
ifconfig wlanX up

Fix this by always re-allocating the rfkill stuff before register.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix possible buffer overrun.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

wl->mutex might already be locked on initialization.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix the initialization for PCMCIA devices.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If i reaches zero, the loop ends, but the postfix decrement subtracts it to -1.
Testing for 'i == 0', later in the function, will not fulfill its purpose.
Signed-off-by: NRoel Kluin <12o3l@tiscali.nl>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix section mismatch warning:

WARNING: vmlinux.o(.data+0x36fcc): Section mismatch: reference to .init.data:prism2_pci_id_table (between 'prism2_pci_drv_id' and 'prism2_pci_funcs')
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2x00 is broken when it comes down to adhoc and master mode.
The main problem is the beaconing, which is completely failing.
Untill a solution has been found, both beacon requiring modes
must be disabled to prevent numerous bug reports.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>