Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Remove fs.h from mm.h. For this,
 1) Uninline vma_wants_writenotify(). It's pretty huge anyway.
 2) Add back fs.h or less bloated headers (err.h) to files that need it.

As result, on x86_64 allyesconfig, fs.h dependencies cut down from 3929 files
rebuilt down to 3444 (-12.3%).

Cross-compile tested without regressions on my two usual configs and (sigh):

alpha              arm-mx1ads        mips-bigsur          powerpc-ebony
alpha-allnoconfig  arm-neponset      mips-capcella        powerpc-g5
alpha-defconfig    arm-netwinder     mips-cobalt          powerpc-holly
alpha-up           arm-netx          mips-db1000          powerpc-iseries
arm                arm-ns9xxx        mips-db1100          powerpc-linkstation
arm-assabet        arm-omap_h2_1610  mips-db1200          powerpc-lite5200
arm-at91rm9200dk   arm-onearm        mips-db1500          powerpc-maple
arm-at91rm9200ek   arm-picotux200    mips-db1550          powerpc-mpc7448_hpc2
arm-at91sam9260ek  arm-pleb          mips-ddb5477         powerpc-mpc8272_ads
arm-at91sam9261ek  arm-pnx4008       mips-decstation      powerpc-mpc8313_rdb
arm-at91sam9263ek  arm-pxa255-idp    mips-e55             powerpc-mpc832x_mds
arm-at91sam9rlek   arm-realview      mips-emma2rh         powerpc-mpc832x_rdb
arm-ateb9200       arm-realview-smp  mips-excite          powerpc-mpc834x_itx
arm-badge4         arm-rpc           mips-fulong          powerpc-mpc834x_itxgp
arm-carmeva        arm-s3c2410       mips-ip22            powerpc-mpc834x_mds
arm-cerfcube       arm-shannon       mips-ip27            powerpc-mpc836x_mds
arm-clps7500       arm-shark         mips-ip32            powerpc-mpc8540_ads
arm-collie         arm-simpad        mips-jazz            powerpc-mpc8544_ds
arm-corgi          arm-spitz         mips-jmr3927         powerpc-mpc8560_ads
arm-csb337         arm-trizeps4      mips-malta           powerpc-mpc8568mds
arm-csb637         arm-versatile     mips-mipssim         powerpc-mpc85xx_cds
arm-ebsa110        i386              mips-mpc30x          powerpc-mpc8641_hpcn
arm-edb7211        i386-allnoconfig  mips-msp71xx         powerpc-mpc866_ads
arm-em_x270        i386-defconfig    mips-ocelot          powerpc-mpc885_ads
arm-ep93xx         i386-up           mips-pb1100          powerpc-pasemi
arm-footbridge     ia64              mips-pb1500          powerpc-pmac32
arm-fortunet       ia64-allnoconfig  mips-pb1550          powerpc-ppc64
arm-h3600          ia64-bigsur       mips-pnx8550-jbs     powerpc-prpmc2800
arm-h7201          ia64-defconfig    mips-pnx8550-stb810  powerpc-ps3
arm-h7202          ia64-gensparse    mips-qemu            powerpc-pseries
arm-hackkit        ia64-sim          mips-rbhma4200       powerpc-up
arm-integrator     ia64-sn2          mips-rbhma4500       s390
arm-iop13xx        ia64-tiger        mips-rm200           s390-allnoconfig
arm-iop32x         ia64-up           mips-sb1250-swarm    s390-defconfig
arm-iop33x         ia64-zx1          mips-sead            s390-up
arm-ixp2000        m68k              mips-tb0219          sparc
arm-ixp23xx        m68k-amiga        mips-tb0226          sparc-allnoconfig
arm-ixp4xx         m68k-apollo       mips-tb0287          sparc-defconfig
arm-jornada720     m68k-atari        mips-workpad         sparc-up
arm-kafa           m68k-bvme6000     mips-wrppmc          sparc64
arm-kb9202         m68k-hp300        mips-yosemite        sparc64-allnoconfig
arm-ks8695         m68k-mac          parisc               sparc64-defconfig
arm-lart           m68k-mvme147      parisc-allnoconfig   sparc64-up
arm-lpd270         m68k-mvme16x      parisc-defconfig     um-x86_64
arm-lpd7a400       m68k-q40          parisc-up            x86_64
arm-lpd7a404       m68k-sun3         powerpc              x86_64-allnoconfig
arm-lubbock        m68k-sun3x        powerpc-cell         x86_64-defconfig
arm-lusl7200       mips              powerpc-celleb       x86_64-up
arm-mainstone      mips-atlas        powerpc-chrp32
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the following section mismatch warnings in microcode.c:
WARNING: arch/i386/kernel/built-in.o(.init.text+0x3966): Section mismatch: reference to .exit.text: (between 'microcode_init' and 'parse_maxcpus')
WARNING: arch/i386/kernel/built-in.o(.init.text+0x3992): Section mismatch: reference to .exit.text: (between 'microcode_init' and 'parse_maxcpus')

The warning are caused by a function marked __init that
calls a function marked __exit.
Functions marked __exit may be discarded either during link or run-time
and thus the reference is not good.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make the microcode driver use the suspend-related CPU hotplug notifications
to handle the CPU hotplug events occuring during system-wide suspend and
resume transitions.  Remove the global variable suspend_cpu_hotplug
previously used for this purpose.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since nonboot CPUs are now disabled after tasks and devices have been
frozen and the CPU hotplug infrastructure is used for this purpose, we need
special CPU hotplug notifications that will help the CPU-hotplug-aware
subsystems distinguish normal CPU hotplug events from CPU hotplug events
related to a system-wide suspend or resume operation in progress.  This
patch introduces such notifications and causes them to be used during
suspend and resume transitions.  It also changes all of the
CPU-hotplug-aware subsystems to take these notifications into consideration
(for now they are handled in the same way as the corresponding "normal"
ones).

[oleg@tv-sign.ru: cleanups]
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the regression resulting from the recent change of suspend code
ordering that causes systems based on Intel x86 CPUs using the microcode
driver to hang during the resume.

The problem occurs since the microcode driver uses request_firmware() in
its CPU hotplug notifier, which is called after tasks has been frozen and
hangs.  It can be fixed by telling the microcode driver to use the
microcode stored in memory during the resume instead of trying to load it
from disk.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Adrian Bunk <bunk@stusta.de>
Cc: Tigran Aivazian <tigran@aivazian.fsnet.co.uk>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Maxim <maximlevitsky@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix bogus gcc warning

linux/arch/i386/kernel/microcode.c:387: warning: ‘new_mc’ may be used uninitialized in this function
Signed-off-by: NAndi Kleen <ak@suse.de>

Many struct file_operations in the kernel can be "const".  Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data.  In addition it'll catch accidental writes at compile time to
these shared resources.

[akpm@osdl.org: sparc64 fix]
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Structure mc_cpu_notifier references a __cpuinit function, but isn't
declared __cpuinitdata itself:

WARNING: arch/i386/kernel/microcode.o - Section mismatch: reference
to .init.text: from .data after 'mc_cpu_notifier' (at offset 0x118)
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Tigran Aivazian <tigran@aivazian.fsnet.co.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

As Adrian pointed out recently, there were still a couple of places where
I should have fixed my email address.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

There was lots of #ifdef noise in the kernel due to hotcpu_notifier(fn,
prio) not correctly marking 'fn' as used in the !HOTPLUG_CPU case, and thus
generating compiler warnings of unused symbols, hence forcing people to add
#ifdefs.

the compiler can skip truly unused functions just fine:

    text    data     bss     dec     hex filename
 1624412  728710 3674856 6027978  5bfaca vmlinux.before
 1624412  728710 3674856 6027978  5bfaca vmlinux.after

[akpm@osdl.org: topology.c fix]
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If the microcode driver is built in (rather than module) there are some,
ehm, interesting effects happening due to the new "call out to userspace"
behavior that is introduced..  and which runs too early.  The result is a
boot hang; which is really nasty.

The patch below is a minimally safe patch to fix this regression for 2.6.19
by just not requesting actual microcode updates during early boot.  (That
is a good idea in general anyway)

The "real" fix is a lot more complex given the entire cpu hotplug scenario
(during cpu hotplug you normally need to load the microcode as well); but
the interactions for that are just really messy at this point; this fix at
least makes it work and avoids a full detangle of hotplug.
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

IA32 manual says if micorcode update's size is 0, then the size is
default size (2048 bytes). But this doesn't suggest all microcode
update's size should be above 2048 bytes to me. We actually had a
microcode update whose size is 1024 bytes. The patch just removed the
check.
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Cc: Tigran Aivazian <tigran@veritas.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add sysfs support.  Currently each CPU has three microcode related
attributes.  One is 'version' which shows current ucode version of CPU.
Tools can use the attribute do validation or show CPU ucode status.  one is
'reload' which allows manually reloading ucode.  Another is
'processor_flags', which exports processor flags, so we can write tools to
check if CPU has latest ucode.  Also add suspend/resume and CPU hotplug
support.

[akpm@osdl.org: cleanups, build fix]
[bunk@stusta.de: Kconfig fixes]
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Acked-by: NTigran Aivazian <tigran@veritas.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Using request_firmware to pull ucode from userspace, so we don't need the
application 'microcode_ctl' to assist.  We name each ucode file according
to CPU's info as intel-ucode/family-model-stepping.  In this way we could
split ucode file as small one.  This has a lot of advantages such as
selectively update and validate microcode for specific models, better
manage microcode file, easily write tools for administerators and so on.
with the changes, we should put all intel-ucode/xx-xx-xx microcode files
into the firmware dir (I had a tool to split previous big data file into
small one and later we will release new style data file).  The init script
should be changed to just loading the driver without unloading
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Acked-by: NTigran Aivazian <tigran@veritas.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Clean up microcode update driver and make it more readable.

[akpm@osdl.org: cleanups]
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Acked-by: NTigran Aivazian <tigran@veritas.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Also fixes all drivers that set this field.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When multiple updates matching a given CPU are found in the update file, the
action taken by the microcode update driver was inappropriate:

- when lower revision microcode was found before matching or higher revision
  one, the driver would needlessly complain that it would not downgrade the
  CPU
- when microcode matching the currently installed revision was found before
  newer revision code, no update would actually take place

To change this behavior, the driver now concludes about possibly updates and
issues messages only when the entire input was parsed.

Additionally, this adds back (in different places, and conditionalized upon
a new module option) some messages removed by a previous patch.
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Cc: Tigran Aivazian <tigran_aivazian@symantec.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Nowadays, even Debian stable ships a microcode_ctl utility recent enough to no
longer use this ioctl.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Acked-by: NTigran Aivazian <tigran_aivazian@symantec.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Semaphore to mutex conversion.

The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jens Axboe <axboe@suse.de>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Acked-by: NAlasdair G Kergon <agk@redhat.com>
Cc: Greg KH <greg@kroah.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Only log data in microcode driver when something is changed Otherwise it
was far too noisy on large systems.

Also remove the printk when it is unloaded.

Cc: tigran@veritas.com
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This driver loops over 'num_online_cpus', but it doesn't account for holes
in the online map created by offlined cpus, and assumes that the cpu
numbers stay linear.
Signed-off-by: NDave Jones <davej@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Passing random input values in eax to cpuid is not a good idea
because the CPU will GPF for unknown ones.
Use the correct x86-64 version that exists for a longer time too.
This also adds a memory barrier to prevent the optimizer from
reordering.

Cc: tigran@veritas.com
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

arch: Use <linux/capability.h> where capable() is used.
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

i386 arch cleanup.  Introduce the serialize macro to serialize processor
state.  Why the microcode update needs it I am not quite sure, since wrmsr()
is already a serializing instruction, but it is a microcode update, so I will
keep the semantic the same, since this could be a timing workaround.  As far
as I can tell, this has always been there since the original microcode update
source.
Signed-off-by: NZachary Amsden <zach@vmware.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!