This patch adds support to retrieve the unique identifier data (VPD page
83 type3) for Logical drives created on SmartIOC 2000 products. In
addition  added a sysfs device structure to expose the id information.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added task management command support to abort any timed out commands
in case of a eh_abort call and to reset lun's in case of eh_reset call.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added support to send out task management commands.

[mkp: removed // fibsize... ]
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added support to send direct pasthru srb commands from management utilty
to the  controller.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added support for drive hotplug add and removal
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added support to set qd of drives in slave_configure.This only works for
HBA1000 attached drives.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Retrieved queue depth from fw and saved it for future use.
Only applicable for HBA1000 drives.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch adds a new functions that periodically sync the time of host
to the adapter. In addition also informs the adapter that the driver is
alive and kicking. Only applicable to the HBA1000 and SMARTIOC2000.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Reworked aac_command_thread into aac_process_events
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch processes Raw IO read medium errors.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch enables the driver to actually process the I/O, or srb replies
from adapter. In addition to any HBA1000 or SmartIOC2000 adapter events.
Signed-off-by: NRaghava Aditya Renukunta <raghavaaditya.renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Make sure that the driver processes error conditions even in the fast
response path for response from the adapter.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Moved the READ and WRITE switch cases to the top. Added a  default
case to the switch case and replaced duplicate scsi result value with a
macro.

The idea is that since most of scsi commands we care about performance
wise are read or write, we need to process them first.

Internally the compiler (GCC) converts a switch case into either a jump
table or a bunch of if else conditions, so placing the often used read,
write cases at the top is an effort in optimization.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch adds support to retrieve the type of each adapter connected
device. Applicable to HBA1000 and SmartIOC2000 products
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

sa_firmware adds the capability to differentiate the new SmartIOC family
of adapters from the series 8 and below.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This  patch lays the groundwork for supporting the new HBA-1000 controller
family.A new INIT structure INIT_STRUCT_8 has been added which allows for a
variable size for MSI-x vectors among other things,  and is used for both
Series-8, HBA-1000 and SmartIOC-2000.
Signed-off-by: NRaghava Aditya Renukunta <raghavaaditya.renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added aacraid.h include guard
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Removed duplicate code that for acquiring and releasing irqs
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

[mkp: whitespace fixes]
Signed-off-by: NLukas Herbolt <lherbolt@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Updated driver version to "15.100.00.00"
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Due existence of loop in the IO path our HBA will receive heavy IOs and
also as driver is not updating the Reply Post Host Index frequently, So
there will be a high chance that our Firmware unable to find any free
entry in the Reply Post Descriptor Queue (i.e. Queue overflow occurs)
and can observe 0x2100 firmware fault.  So to fix this, we have defined
a thresh hold value. After continuously processing this thresh hold
number of reply descriptors driver will update the Reply Descriptor Host
Index so that this thresh hold number of reply descriptors entries will
be freed and these entries will be available for firmware and we won't
observe this Firmware fault. We have defined this threshold value as
1/3rd of the hba queue depth.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Small glitch/degraded performance in Crusader is improved with SAS
drives by removing unnecessary spinlocks while clearing scsi command in
drivers internal lookup table.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Driver processes the event MPI26_EVENT_ACTIVE_CABLE_DEGRADED when a
cable is present and is running at a degraded speed (below the SAS3 12
Gb/s rate). Prints added to inform the user that the cable is not
running at optimal speed.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

- Setting coalescing has a significant negative impact on low
  queue-depth performance.
- Does not help high queue-depth performance.
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Reviewed-by: NScott Benesh <scott.benesh@microsemi.com>
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Remove a piece of code in storvsc_queuecommand that tries to pass the
physical address of the kernel struct scatterlist pointer to the host.

Fortunately the code can't ever be reached anyway.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The atari_scsi driver should not access Falcon DMA chip registers unless
it has acquired exclusive access to that chip. If the driver doesn't
have exclusive access then there's no need for a DMA reset as there are
no scsi commands in progress.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Handle timeout or bus phase change errors that could occur when sending
the IDENTIFY message.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Avoid various warnings from "make C=1" by annotating a couple of
unlock-then-lock sequences, replacing a zero with NULL and correcting
some type casts.

Also avoid a warning from "make W=1" by adding braces.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The NCR5380 wrapper drivers don't export symbols or declarations and
don't actually need separate header files. Most of these header files
were removed already; only sun3_scsi.h and g_NCR5380.h remain.

Move the remaining definitions to the corresponding .c files to improve
readability and proximity. The #defines which influence the #included
core driver are no longer mixed up with unrelated #defines and #includes.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Remove dead code inside #if 0 conditionals.

Remove the #ifdef __KERNEL__ test, since NCR5380.h has no definitions
that relate to userspace code.

Remove two redundant macro definitions which were overlooked in
commit e9db3198 ("sun3_scsi: Adopt NCR5380.c core driver").
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The DIFFERENTIAL and PARITY option macros are unused: no supported
hardware uses differential signalling and the core driver never
implemented parity checking. These options just waste space in the host
info string.

While we are here, fix a typo in the NCR5380_info() kernel-doc comment.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

There is an issue that hisi_sas_dev.running_req is not
decremented properly for internal abort and TMF.

To resolve, only decrease running_req in hisi_sas_slot_task_free()
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

There is a potential probe issue in how we trigger the hw initialisation.
Although we use 1s timer to delay hw initialisation, there is still a
potential that sas_register_ha() is not be finished before we start
the PHY init from hw->hw_init().
To avoid this issue, initialise the hw after sas_register_ha() in the
same probe context.
Note: it is not necessary to use 1s timer now (modified v2 hw only).
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Downgrade the exit print in hisi_sas_internal_task_abort()
to dbg level, as info is not required.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NXiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Correctly set registers in v2 for root PHY hardreset for directly
attached disk.
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The message to inform that the controller has no refclk
is currently at warning level, which is unnecessary, so
downgrade to debug.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NXiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Set SMP connection timeout and continue AWT timer;
Clear ITCT table when dev gone.
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The v2 SAS controller needs more time to detect channel idle
and send setup link request than SATA disk does, so it is
difficult for the SAS controller to setup an STP link. Therefore
it may cause some IO timeouts.

We need to periodically configure the SAS controller so it
doesn't receive STP setup requests from SATA disks for a while,
so IO can be sent during this period.
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When I reversed the patch to re-add the lpfc_soft_wwn parameter feature,
it re-added code that had a long-standing bug. (that's what I get I
guess :)

As Dan Carpenter pointed out - error checks looked at wrong polarity.  0
is success, -errno is failure. Updated checks.
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In sd.c there are two comment references to 'struct scsi_device *sdp' as
an argument.  One of the references has a typo and the other should be a
reference to 'struct device *dev' instead.

Fixed by correcting the typo in the first and changing the explanation
in the second.
Signed-off-by: NJohn Pittman <jpittman@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>