The ab8500 device is a child of the prcmu device, which is a memory mapped
bus device, whose children are addressable using physical memory addresses,
not using mailboxes, so a mailbox number in the ab8500 node cannot be
parsed by DT. Nothing uses this number, since it was only introduced
as part of the failed attempt to clean up prcmu mailbox handling, and
we can simply remove it.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch adds #dma-cells property to PL330 DMA controller nodes for
supporting generic dma dt bindings on SOCFPGA platform. #dma-channels
and #dma-requests are not required now but added in advance.
Signed-off-by: NPadmavathi Venna <padma.v@samsung.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

The orion5x-lacie-ethernet-disk-mini-v2.dts file was using
"marvell-orion5x-88f5182" as a compatible string, while it should have
been "marvell,orion5x-88f5182".
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

There is no need to have a #address-cells property in the MPIC Device
Tree node, and more than that, having it confuses the of_irq_map_raw()
logic, which will be used by the Marvell PCIe driver.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Setting the reg-io-width to 1 byte represents more accurate
description of the HW.

This will fix an issue where UART driver causes kernel
panic during bootup. Gregory CLEMENT traced the issue to
autoconfig() in 8250.c, where the existence of FIFO is
checked from UART_IIR register. The register is now read as
32-bit value as the reg-io-width is set to 4-bytes. The
retuned value seems to contain bogus data for bits 31:8,
causing the issue.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: NMasami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The commit:

  48be9ac9 ARM: Dove: split legacy and DT setup

removed the RTC initialization.  This patch re-enables the RTC
via the DT.
Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This patch modifies the Armada 370 Reference Design DTS file to enable
support for the two USB ports found on this board.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The Marvell RTC on Kirkwood makes use of the runit clock. Ensure the
driver clk_prepare_enable() this clock, otherwise there is a danger
the SoC will lockup when accessing RTC registers with the clock
disabled.
Reported-by: NSimon Baatz <gmbnomis@gmail.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NSimon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The kirkwood SoC GPIO cores use the runit clock. Add code to
clk_prepare_enable() runit, otherwise there is a danger of locking up
the SoC by accessing the GPIO registers when runit clock is not
ticking.
Reported-by: NSimon Baatz <gmbnomis@gmail.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NSimon Baatz <gmbnomis@gmail.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

When DT support for kirkwood was first introduced, there was no clock
infrastructure.  As a result, we had to manually pass the
clock-frequency to the driver from the device node.

Unfortunately, on kirkwood, with minimal config or all module configs,
clock-frequency breaks booting because of_serial doesn't consume the
gate_clk when clock-frequency is defined.

The end result on kirkwood is that runit gets gated, and then the boot
fails when the kernel tries to write to the serial port.

Fix the issue by removing the clock-frequency parameter from all
kirkwood dts files.

Booted on dreamplug without earlyprintk and successfully logged in via
ttyS0.
Reported-by: NSimon Baatz <gmbnomis@gmail.com>
Tested-by: NSimon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Before jumping to (position independent) C-code from the decompressor's
assembler world we set-up the C environment. This setup currently does not
set r9, which for arm-none-uclinux-uclibceabi toolchains is by default
expected to be the PIC offset base register (IE should point to the
beginning of the GOT).

Currently, therefore, in order to build working kernels that use the
decompressor it is necessary to use an arm-linux-gnueabi toolchain, or
similar. uClinux toolchains cause a prefetch abort to occur at the beginning
of the decompress_kernel function.

This patch allows uClinux toolchains to build bootable zImages by forcing
the -mno-single-pic-base option, which ensures that the location of the GOT
is re-derived each time it is required, and r9 becomes free for use as a
general purpose register.

This has a small (4% in instruction terms) advantage over the alternative of
setting r9 to point to the GOT before calling into the C-world.
Signed-off-by: NJonathan Austin <jonathan.austin@arm.com>
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

As DT support for clocks and smp_twd is enabled, add clock entry
for smp_twd clock to DT.

This fixes the following error while booting the kernel:
smp_twd: clock not found -2
Signed-off-by: NPrashant Gaikwad <pgaikwad@nvidia.com>
[swarren: include kernel log spew that this fixes]
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

commit 5f300acd
(ARM: 7152/1: distclean: Remove generated .dtb files)
ensured that dtbs were cleaned up when they were in
arch/arm/boot.
However, with the following commit:
commit 499cd829
(ARM: dt: change .dtb build rules to build in dts directory)

make clean now leaves dtbs in arch/arm/boot/dts/
untouched. Include dts directory so that clean-files rule
from arch/arm/boot/dts/Makefile is invoked when make
clean is done.

Cc: Dirk Behme <dirk.behme@de.bosch.com>
CC: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

BCM2835-ARM-Peripherals.pdf states that the I2C module's input clock is
nominally 150MHz, and that value is currently reflected in bcm2835.dtsi.
However, practical measurements show that the rate is actually 250MHz,
and this agrees with various downstream kernels.

Switch the I2C clock's frequency to 250MHz so that the generated bus
clock rate is accurate.
Signed-off-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

According to fsl,imx53-pinctrl.txt, the pin number of DISP1_DAT_21
should be 545, while 543 is IPU_CSI0_D_3.  Along with the change,
one duplication of DISP1_DAT_0 in disp1-grp1 is removed.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The Armada 370 Reference Design board has one SD card slot, directly
connected to the SDIO IP of the SoC, so we enable this IP. there are no
GPIOs for card-detect and write-protect so we do not specify any.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Signed-off-by: NJason Cooper <jason@lakedaemon.net>
Tested-by: NAndrew Lunn <andrew@lunn.ch>

Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Add a DT node for I2C and pinctrl hog for the pins. There appears to
be an i2c bus on topkick with a device on it:

i2cdetect 0
WARNING! This program can confuse your I2C bus, cause data loss and worse!
I will probe file /dev/i2c-0.
I will probe address range 0x03-0x77.
Continue? [Y/n] y
     0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
00:          -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: -- -- -- -- 64 -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Signed-off-by: NJason Cooper <jason@lakedaemon.net>

of_serial now has support for using clocks property and we have
a DT clock provider. This patch replaces the hard coded clock-frequency
property with a clocks phandle to tclk.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This patch add support for the SPI flash MX25l25635E which is present
on the Armada 370 DB board. This flash stores the bootloader and its
environment.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This patch add support for the SPI flash M25P64 which is present on
the Armada XP DB board. This flash stores the bootloader and its
environment.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This patch adds an SPI master device node for Armada XP-GP board.
This master node is an SPI flash controller 'n25q128a13'.

Since there is no 'partitions' node declared, one full sized
partition named as the device will be created.

Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Lior Amsalem <alior@marvell.com>
Tested-by: NGregory Clement <gregory.clement@free-electrons.com>
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: NGregory Clement <gregory.clement@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The Armada 370 and Armada XP SoC has an SPI controller.
This patch adds support for this controller in Armada 370
and Armada XP SoC common device tree files.

Note that the Armada XP SPI register length is 0x50 bytes,
while Armada 370 SPI register length is 0x28 bytes,
so we choose the smaller of the two.

Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Lior Amsalem <alior@marvell.com>
Acked-by: NGregory Clement <gregory.clement@free-electrons.com>
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Now that the time-armada-370-xp support local timers, updated the
device tree to take it into account.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

With DT support for orion-ehci also convert Dove to it and
remove the legacy calls and clock aliases.

This patch is based on "ARM: Dove: split legacy and DT setup"
applied to mvebu/boards recently.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This patch activates every USB port provided by each SoC.
Except for Armada XP Openblocks AX3-4 board,
where we enable only the first two USB ports
until we have more information on the third one usage.

Cc: Lior Amsalem <alior@marvell.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The Armada 370 and Armada XP SoC has an Orion EHCI USB controller.
This patch adds support for this controller in Armada 370
and Armada XP SoC common device tree files.

Cc: Lior Amsalem <alior@marvell.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The OpenBlocks AX3-4 board has one software-controlled button on the
front side, labeled "INIT", so we add minimal support for this button
in the kernel.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Remove C code and add a Device Tree node in its place.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NSimon Guinot <simon.guinot@sequanux.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Add a sub-node into the I2C node to represent the adt7476 device.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Remove the C code and add a Device Tree node for gpio-poweroff.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

CuBox needs to enable USB power on a gpio pin. Add a fixed regulator
to always enable usb power on boot.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

gpio-leds has support for pinctrl allocation, make use of it.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The 88f6282 has one more TWSI(TWSI1). This add the information to enable
pinctl of TWSI1.
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This commit adds a pinmux option, pmx_sdio, to enable the muxing of
the SDIO interface on the 88F6282 SoC from Marvell.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>