Some DSP modules have user configurable parameters. These
parameters are required by modules in the following scenario
	-  during initialization
	-  after initialization using set parameter

This patch adds helper routine to set module parameters using
large config set IPC message and removes params to be passed as
init module routine.
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The firmware name is hard coded which doesnt allow to load
different platforms for various platforms so get this name from
available machine table and pass it to dsp context for loading
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Widget FW topology private data already has the information
on the channel map, ch_cfg and interleaving. This patch removes
the calculation of channel_map in driver and reads the value
directly from widget private data.
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NSubhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The module pin formats are considered homogeneous, but some
modules can have different pcm formats on different pins, like
reference signal for a module.

This patch add support for configuration of each pin of module
and allows us to specify if pins and homogeneous or heterogeneous
Signed-off-by: NHardik T Shah <hardik.t.shah@intel.com>
Signed-off-by: NOmair M Abdullah <omair.m.abdullah@intel.com>
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NSubhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

For supporting multiple dynamic pins, module state check is
incorrect. In case of unbind, module state need to be changed to
uninit if all pins in the module is is unbind state.
To handle module state correctly add pin state and use pin
state check to set module state correctly.
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

If copier instance is connected to a DMA gateway then driver
needs to configure the gateway configuration otherwise set
it to invalid.
This patch sets the non gateway copier node value to invalid.
Signed-off-by: NDharageswari.R <dharageswari.r@intel.com>
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

If DSP initialization fails, ipc to disable notification
will cause NULL ptr exception as ipc is not initialized.
This patch returns error if dsp init fails before
sending disable notification ipc.
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Each FW modules can report underrun/overrun notification from
all modules. This patch disables underrun/overrun notification after
firmware is loaded.
This will be supportted for debug mode only thru debugfs
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

DSP firmware has interface change for SSP node index structure.
New FW interface removes the dual_mono field and adds 4 bits for
TDM slot group index. This patch updates the ssp dma to align with
the DSP firmware structure.
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

To manage DSP we need to create processing pipeline and on cleanup destroy
them. So we add create and destroy routines for pipelines The pipelines need
to to be executed so we add pipeline run and stop routines
All these send required IPCs to DSP using IPC routines added earlier
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

A module needs to be instantiated and then connected with other modules. On
cleanup we need to disconnect the module.
This is achieved by helpers module init, bind and unbind which are added
here
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

SRC and converter modules are required to do frequency and channel
conversion in DSP. Both take base module configuration and additional SRC
and converter parameters. The helpers here are added to calculate the values
for these modules
Signed-off-by: NHardik T Shah <hardik.t.shah@intel.com>
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This adds helper functions to calculate parameters required for base module
format and copier module. A generic module is modelled by base module.
Copier module is responsible for getting/sending data to FE (host DMAs) and
BE (link HDA DMA, SSP, PDM)
This also ads module pin management helpers which help in finding pins to
use or freeing them up
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This helper function will be used by the Skylake driver for dsp and
ipc initialization if processing pipe capability is supported.
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>