Use DT to describe the two XOR DMA engines on Kirkwood. Remove the
C code initialization.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>

With true DT clock providers available switch Kirkwood clock setup in
DT- enabled boards. While AUXDATA can be removed completely from bus
probing, some devices still don't know about DT. Therefore, some clkdev
aliases are created until these devices also move to DT.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>

Based on work by Michael Walle and Jason Cooper.

Added support for getting the interrupt number and address of SRAM
from DT.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Conflicts:

	arch/arm/mach-kirkwood/board-dt.c

Add support for instantiating this driver from device tree, and add
the necassary DT information to the kirkwood.dtsi file.

This is based on previous work by Michael Walle and Jason Cooper.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NJosh Coombs <josh.coombs@gmail.com>

Add device tree support to the Orion watchdog timer, and enable its
use in the kirkwood devices using device tree.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NSebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Tested-by: NSimon Baatz <gmbnomis@gmail.com>

The MV64XXX I2C driver needs a clock in order to calculate the baud
rate factors. So add an clk to the clk tree. Also add the base DT
properties for kirkwood devices.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>

Conflicts:
	arch/arm/mach-kirkwood/common.c

Populate the devices with auxdata to set the device names which are used by
clkdev to lookup the clocks.
Signed-off-by: NMichael Walle <micheal@walle.cc>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
---
v2: Add interrupts properties, although not used.

Both IRQ and GPIO controllers can now be represented in DT.  The IRQ
controllers are setup first, and then the GPIO controllers. Interrupts
for GPIO lines are placed directly after the main interrupts in the
interrupt space.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NSebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Tested-by: NJosh Coombs <josh.coombs@gmail.com>
Tested-by: NSimon Baatz <gmbnomis@gmail.com>

It has been decided to use marvell, not mrvl, in the compatibility
property. Search & replace.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>

Add default configuration for NAND, to be enabled in your board config. Ensure
clock gating is set appropriately when the NAND is enabled.
Acked-by: NJason Cooper <jason@lakedaemon.net>
Signed-off-by: NJamie Lentin <jm@lentin.co.uk>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Signed-off-by: NJason Cooper <jason@lakedaemon.net>
Acked-by: NArnd Bergmann <arnd@arndb.de>

Define both uarts in kirkwood.dtsi as they are common to all kirkwood
SoCs.  Each board may enable all or none of them, so they are disabled
by default.  uart0 is enabled for the dreamplug.

tclk can vary for each board, so we leave it undefined in the kirkwood
dtsi.  Each board can then set it as appropriate when enabling the uart.
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Also, use inclusive register size for uart0.
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Initially, copied guruplug-setup.c and did s/guruplug/dreamplug/g.
Then, switched to SPI based NOR flash.

After talking to Arnd Bergman, chose an incremental approach to adding
devicetree support.  First, we use the dtb to tell us we are on the
dreamplug, then we gradually port over drivers.

Driver porting will start with the uart (see next patch), and progress
from there.  Possibly, spi/flash/partitions will be next.

When done, board-dt.c will no longer be dreamplug specific, and dt's can
be made for the other kirkwood boards.
Signed-off-by: NJason Cooper <jason@lakedaemon.net>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>