This adds AUX vectors for the L1I,D, L2 and L3 cache levels
providing for each cache level the size of the cache in bytes
and the geometry (line size and number of ways).

We chose to not use the existing alpha/sh definition which
packs all the information in a single entry per cache level as
it is too restricted to represent some of the geometries used
on POWER.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

All shipping firmware versions have it wrong in the device-tree
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Retrieved from device-tree when available
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

We have two set of identical struct members for the I and D sides
and mostly identical bunches of code to parse the device-tree to
populate them. Instead make a ppc_cache_info structure with one
copy for I and one for D
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

It will be used to calculate the associativity
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In a number of places we called "cache line size" what is actually
the cache block size, which in the powerpc architecture, means the
effective size to use with cache management instructions (it can
be different from the actual cache line size).

We fix the naming across the board and properly retrieve both
pieces of information when available in the device-tree.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

We don't patch instructions based on the cache lines or block
sizes these days.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The variables are defined twice in setup_32.c and setup_64.c, do it
once in setup-common.c instead
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

It's an kernel private macro, it doesn't belong there
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Enable support for GCC plugins on powerpc.

Add an additional version check in gcc-plugins-check to advise users to
upgrade to gcc 5.2+ on powerpc to avoid issues with header files (gcc <=
4.6) or missing copies of rs6000-cpus.def (4.8 to 5.1 on 64-bit
targets).
Signed-off-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Commit 38addce8 ("gcc-plugins: Add latent_entropy plugin") excludes
certain powerpc early boot code from the latent entropy plugin by adding
appropriate CFLAGS. It looks like this was supposed to cover
prom_init.o, but ended up saying init.o (which doesn't exist) instead.
Fix the typo.

Fixes: 38addce8 ("gcc-plugins: Add latent_entropy plugin")
Signed-off-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The variable DISABLE_LATENT_ENTROPY_PLUGIN is defined when
CONFIG_PAX_LATENT_ENTROPY is set. This is leftover from the original PaX
version of the plugin code and doesn't actually exist. Change the condition
to depend on CONFIG_GCC_PLUGIN_LATENT_ENTROPY instead.

Fixes: 38addce8 ("gcc-plugins: Add latent_entropy plugin")
Signed-off-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Stub out the debugfs functions so that the build doesn't break when
CONFIG_DEBUG_FS=n.
Reported-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: NIan Munsie <imunsie@au1.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

As we add the ability to do DLPAR of additional devices through
the sysfs interface we need to know which devices are supported.
This adds the reporting of supported devices with a comma separated
list reported in the existing /sys/kernel/dlpar.
Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Extend the existing PRRN infrastructure to perform the actual affinity
updating for cpus and memory in addition to the device tree updating.
For cpus, dynamic affinity updating already appears to exist in the
kernel in the form of arch_update_cpu_topology(). For memory, we must
place a READD operation on the hotplug queue for any phandle included in
the PRRN event that is determined to be an LMB.
Signed-off-by: NJohn Allen <jallen@linux.vnet.ibm.com>
Reviewed-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Currently, memory must be hot removed and subsequently re-added in order
to dynamically update the affinity of LMBs specified by a PRRN event.
Earlier implementations of the PRRN event handler ran into issues in which
the hot remove would occur successfully, but a hotplug event would be
initiated from another source and grab the hotplug lock preventing the hot
add from occurring. To prevent this situation, this patch introduces the
notion of a hot "readd" action for memory which atomizes a hot remove and
a hot add into a single, serialized operation on the hotplug queue.
Signed-off-by: NJohn Allen <jallen@linux.vnet.ibm.com>
Reviewed-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

When adding and removing LMBs we should make the acquire/release of
the DRC a separate step to allow for a few improvements. First
this will ensure that LMBs removed during a remove by count operation
are all available if a error occurs and we need to add them back. By
first removeing all the LMBs from the kernel before releasing their
DRCs the LMBs are available to add back should an error occur.

Also, this will allow for faster re-add operations of memory for
PRRN event handling since we can skip the unneeded step of having
to release the DRC and the acquire it back.
Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NJohn Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Signed-off-by: NMadhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Add a few things that have been missed from .gitignore over the years.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

CONFIG_PPC_PTDUMP currently selects CONFIG_DEBUG_FS. But CONFIG_DEBUG_FS
is user-selectable, so we shouldn't select it. Instead depend on it.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Commit db911217 ("powerpc: Turn on BPF_JIT in ppc64_defconfig")
only added BPF_JIT to the ppc64 defconfig. Add it to our powernv
and pseries defconfigs too.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Acked-by: NNaveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

We added support for HAVE_CONTEXT_TRACKING, but placed the option inside
PPC_PSERIES.

This has the undesirable effect that NO_HZ_FULL can be enabled on a
kernel with both powernv and pseries support, but cannot on a kernel
with powernv only support.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In __get_user_nosleep, we create an intermediate pointer for the
user address we're about to fetch. We currently don't tag this
pointer as const. Make it const, as we are simply dereferencing
it, and it's scope is limited to the __get_user_nosleep macro.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In __get_user_nocheck, we create an intermediate pointer for the
user address we're about to fetch. We currently don't tag this
pointer as const. Make it const, as we are simply dereferencing
it, and it's scope is limited to the __get_user_nocheck macro.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In __get_user_check, we create an intermediate pointer for the
user address we're about to fetch. We currently don't tag this
pointer as const. Make it const, as we are simply dereferencing
it, and it's scope is limited to the __get_user_check macro.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

opal_lpc_init() is called from an __init routine, and calls other __init
routines, so should also be __init, init?

Fixes: 023b13a5 ("powerpc/powernv: Add support for direct mapped LPC on POWER9")
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Use remove_pagetable() and friends for radix vmemmap removal.

We do not require the special-case handling of vmemmap done in the x86
versions of these functions. This is because vmemmap_free() has already
freed the mapped pages, and calls us with an aligned address range.

So, add a few failsafe WARNs, but otherwise the code to remove physical
mappings is already sufficient for vmemmap.
Signed-off-by: NReza Arbab <arbab@linux.vnet.ibm.com>
Acked-by: NBalbir Singh <bsingharora@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Tear down and free the four-level page tables of physical mappings
during memory hotremove.

Borrow the basic structure of remove_pagetable() and friends from the
identically-named x86 functions. Reduce the frequency of tlb flushes and
page_table_lock spinlocks by only doing them in the outermost function.
There was some question as to whether the locking is needed at all.
Leave it for now, but we could consider dropping it.

Memory must be offline to be removed, thus not in use. So there
shouldn't be the sort of concurrent page walking activity here that
might prompt us to use RCU.
Signed-off-by: NReza Arbab <arbab@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Wire up memory hotplug page mapping for radix. Share the mapping
function already used by radix_init_pgtable().
Signed-off-by: NReza Arbab <arbab@linux.vnet.ibm.com>
Acked-by: NBalbir Singh <bsingharora@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Move the page mapping code in radix_init_pgtable() into a separate
function that will also be used for memory hotplug.

The current goto loop progressively decreases its mapping size as it
covers the tail of a range whose end is unaligned. Change this to a for
loop which can do the same for both ends of the range.
Signed-off-by: NReza Arbab <arbab@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Use the new non-PCI ISA bridge support to expose the POWER9
LPC bus as direct mapped via the ISA IO port range. This
enables direct access via drivers such as 8250
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The POWER9 chip supports an LPC bus that isn't hanging
off a PCI bus, so let's add support for that, mapping it
to the reserved space at ISA_IO_BASE
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

We'll be adding non-PCI isa bridge support so let's not
have all the definition in pci-bridge.h
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Document the device-tree bindings defining the the properties under
the @power-mgt node in the device tree that describe the idle states
for Linux running on baremetal POWER servers.

These bindings are documented separately instead of using the the
common idle state bindings since the idle-states on POWER servers
are exposed as property arrays where as the common idle state bindings
expect idle-states to be described as nodes.
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NGautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The power9_idle_stop method currently takes only the requested stop
level as a parameter and picks up the rest of the PSSCR bits from a
hand-coded macro. This is not a very flexible design, especially when
the firmware has the capability to communicate the psscr value and the
mask associated with a particular stop state via device tree.

This patch modifies the power9_idle_stop API to take as parameters the
PSSCR value and the PSSCR mask corresponding to the stop state that
needs to be set. These PSSCR value and mask are respectively obtained
by parsing the "ibm,cpu-idle-state-psscr" and
"ibm,cpu-idle-state-psscr-mask" fields from the device tree.

In addition to this, the patch adds support for handling stop states
for which ESL and EC bits in the PSSCR are zero. As per the
architecture, a wakeup from these stop states resumes execution from
the subsequent instruction as opposed to waking up at the System
Vector.

The older firmware sets only the Requested Level (RL) field in the
psscr and psscr-mask exposed in the device tree. For older firmware
where psscr-mask=0xf, this patch will set the default sane values that
the set for for remaining PSSCR fields (i.e PSLL, MTL, ESL, EC, and
TR). For the new firmware, the patch will validate that the invariants
required by the ISA for the psscr values are maintained by the
firmware.

This skiboot patch that exports fully populated PSSCR values and the
mask for all the stop states can be found here:
https://lists.ozlabs.org/pipermail/skiboot/2016-September/004869.html

[Optimize the number of instructions before entering STOP with
ESL=EC=0, validate the PSSCR values provided by the firimware
maintains the invariants required as per the ISA suggested by Balbir
Singh]
Acked-by: NBalbir Singh <bsingharora@gmail.com>
Signed-off-by: NGautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In the current code for powernv_add_idle_states, there is a lot of code
duplication while initializing an idle state in powernv_states table.

Add an inline helper function to populate the powernv_states[] table
for a given idle state. Invoke this for populating the "Nap",
"Fastsleep" and the stop states in powernv_add_idle_states.
Signed-off-by: NGautham R. Shenoy <ego@linux.vnet.ibm.com>
Acked-by: NBalbir Singh <bsingharora@gmail.com>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Balbir pointed out that the name of the function pnv_arch300_idle_init
was inconsistent with the names of the variables and functions
pertaining to POWER9 features in book3s_idle.S.

This patch renames pnv_arch300_idle_init to pnv_power9_idle_init.

This patch does not change any behaviour.
Signed-off-by: NGautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Currently all the low-power idle states are expected to wake up
at reset vector 0x100. Which is why the macro IDLE_STATE_ENTER_SEQ
that puts the CPU to an idle state and never returns.

On ISA v3.0, when the ESL and EC bits in the PSSCR are zero, the CPU
is expected to wake up at the next instruction of the idle
instruction.

This patch adds a new macro named IDLE_STATE_ENTER_SEQ_NORET for the
no-return variant and reuses the name IDLE_STATE_ENTER_SEQ
for a variant that allows resuming operation at the instruction next
to the idle-instruction.
Acked-by: NBalbir Singh <bsingharora@gmail.com>
Signed-off-by: NGautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Add detection of NPU2 PHBs. NPU2/NVLink2 has a different register
layout for the TCE kill register therefore TCE invalidation should be
done via the OPAL call rather than using the register directly as it
is for PHB3 and NVLink1. This changes TCE invalidation to use the OPAL
call in the case of a NPU2 PHB model.
Signed-off-by: NAlistair Popple <alistair@popple.id.au>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

POWER9 contains an off core mmu called the nest mmu (NMMU). This is
used by other hardware units on the chip to translate virtual
addresses into real addresses. The unit attempting an address
translation provides the majority of the context required for the
translation request except for the base address of the partition table
(ie. the PTCR) which needs to be programmed into the NMMU.

This patch adds a call to OPAL to set the PTCR for the nest mmu in
opal_init().
Signed-off-by: NAlistair Popple <alistair@popple.id.au>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>