We don't want to modify all source files the day the FSF moves.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: NEnrico Butera <ebutera@users.sourceforge.net>
Acked-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Record the value returned by subdevs from s_stream(0) and handle stop
failures when an error occurs.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: NEnrico Butera <ebutera@users.sourceforge.net>
Acked-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The field order must match between the source and sink pads, or the sink
pad field order must be NONE. This allows connecting an interlaced
source to a bridge that has no hardware support for interlaced formats.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: NEnrico Butera <ebutera@users.sourceforge.net>
Acked-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add support for the V4L2_CID_TEST_PATTERN control. When the solid colour
mode is selected, additional controls become available for setting the
solid four solid colour components.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

In many cases the test pattern has selectable values for each colour
component. Implement controls for raw bayer components. Additional controls
should be defined for colour components that are not covered by these
controls.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Now that xc5000_set_params() is also called during resume,
move the code that checks for the firmware to happen there.

This way, the firmware will be loaded either for analog or
digital TV when .resume callback is called.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

When DVB is streaming and suspend is called, it will call
au0828_stop_transport(), with will clean the streaming flag.

Due to that, stop_urb_transfer() will be called twice,
causing an oops.

So, we need another flag to be used at resume, telling it
to restart DVB.

While here, add a logic at stop_urb_transfer() to prevent
it of being called twice, and convert the usb_streaming
flag into boolean.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

dev->dvb is always not null, as it is an area at the dev
memory. So, checking if (dev->dvb) is always true.

Instead of this stupid check, what the code wants to do is
to know if the DVB was successully registered.

Fix it by checking, instead, for dvb->frontend. It should
also be sure that this var will be NULL if the device was
not properly initialized.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

xc5000_set_params() is a bad name for a function that
handles only digital TV. Rename it to xc5000_set_digital_params(),
and proper name the generic function that works for both
digital and analog.

No functional changes.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

If a device suspends/hibertates with a station tuned, restore
the tuner station at resume.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

As we need a function that reapply the last tuned radio,
in order to do resume, split the code that validates and
updates the internal priv struct from the ones that
actually set radio and TV.

A latter patch will add support for resume.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

As we'll be adding a code to resume tuner operation, we
need to move the code that actually sets DTV on a separate
function, to be called by the resume code.

No functional changes, just code got moved.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

After xc5000 stops working, it waits for 5 seconds, waiting
for a new usage. Only after that it goes to low power mode.

If a suspend event happens before that, a work queue will
remain active, with causes suspend to crash.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

While several tuners have some sort of suspend/resume
implementation, this is currently mangled with an optional
.sleep callback that it is also used to put the device on
low power mode.

Not all drivers implement it, as returning the driver from
low power may require to re-load the firmware, with takes
some time. Also, some drivers may delay it.

So, the more coherent is to add two new optional callbacks
that will let the tuners to directy implement suspend and
resume callbacks if they need.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Suspend/resume conditions can be very tricky. Add some info
printk's to help tracking what's happening there.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Instead of using printk(KERN_foo, use pr_foo() macros.

No functional changes.

Note: we should do the same for dprintk(), but that would
require to remove the dprintk levels. So, for now, let's
not touch on it.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

No timers should be enabled during suspend. So,
stop them. At resume time, we should do the proper
initialization for it to keep working.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The STREAM_ON state is used by s_format callback,
but the driver never sets it.

Fix it. This will also be needed in order to handle
suspend/resume ops.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The scheduled work should be cancelled during suspend.

At resume time, we need to set the frontend again. So,
add such logic to the driver.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

At resume, we should restore the register contents. So,
reenable the bridge and GPIO settings.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Trying to make au0828 to suspend can do very bad things, as
the polling Kthread is not handled. We should disable it
during suspend, only re-enabling it at resume.

Still, analog and digital TV won't work, as we don't reinit
the settings at resume, but at least it won't hang.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Remove CONFIG_VIDEO_AU0828_RC scope around au0828_rc_register()
and au0828_rc_unregister() calls in au0828-core
Signed-off-by: NShuah Khan <shuah.kh@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Define au0828_rc_*() stubs to avoid compile errors when
VIDEO_AU0828_RC is disabled and avoid the need to enclose
au0828_rc_*() in ifdef CONFIG_VIDEO_AU0828_RC in .c files.
Signed-off-by: NShuah Khan <shuah.kh@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

It doesn't make sense to handle an IR code given before
suspending after the device resume. So, turn off IR
int while suspending.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

As the RC kthread can re-enable IR int, we should first
cancel the kthread and then disable IR int.

While here, remove a temporary debug printk.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

When the DVB code sets the frontend, it disables the IR
INT, probably due to some hardware bug, as there's no code
there at au8522 frontend that writes on register 0xe0.

Fixing it at au8522 code is hard, as it doesn't know if the
IR is enabled or disabled, and just restoring the value of
register 0xe0 could cause other nasty effects. So, better
to add a hack at au0828-input polling interval to enable int,
if disabled.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

HVR-850 also has a remote. Enable it.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The IR code increases the power consumption of the device.
Allow to disable it via modprobe parameter.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This sleep was doing some debouncing on the original driver.
This is not needed on Linux, because the RC core and the input
layer already takes care of it.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Remove the now unnecessary memset too.
Signed-off-by: NJoe Perches <joe@perches.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Sometimes dev->tuner_type is compared to UNSET, sometimes to TUNER_ABSENT,
but these defines have different values.

Standardize to TUNER_ABSENT.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

make reset control optional for i.MX27

The patch "[media] coda: add reset control support" introduced a build failure
if CONFIG_RESET_CONTROLLER is disabled:

    drivers/media/platform/coda.c:3734:2: error: implicit declaration of
     function 'devm_reset_control_get'

Since not all SoCs containing CODA VPUs do have a system reset controller,
use devm_reset_control_get_optional to make it optional.
Reported-by: NShawn Guo <shawn.guo@linaro.org>
Reported-by: NOlof's autobuilder <build@lixom.net>
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Fixes the following sparse warnings:

drivers/media/radio/radio-miropcm20.c:193:33: warning:
 Using plain integer as NULL pointer
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This patch add the DT support for Atmel ISI driver.
It use the same v4l2 DT interface that defined in video-interfaces.txt.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Cc: devicetree@vger.kernel.org
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Now the platform data is initialized by allocation of isi
structure. In the future, we use pdata to store the dt parameters.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add support for devicetree probe for the rcar-vin
driver.
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
[g.liakhovetski@gmx.de fix a typo, sort headers alphabetically]
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add device-tree support to pxa_camera host driver.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
[g.liakhovetski@gmx.de: added of_node_put()]
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add device-tree support for mt9m111 camera sensor.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>