Add support for Advantech/GE B650v3 board.
Signed-off-by: NAkshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add support for Advantech/GE B450v3 board.
Signed-off-by: NAkshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Advantech has 3 carrier boards (B450v3, B650v3, B850v3) which use
the Advantech BA-16 module (based on iMX6D). This file has the
devicetree entries that are common to all 3 boards.
Signed-off-by: NAkshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: NJustin Waters <justin.waters@timesys.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add support for Advantech BA-16 module based on iMX6D processor

Basic information about the module:
 - Module manufacturer: Advantech
 - CPU: Freescale ARM Cortex-A9 i.MX6
 - SPECS:
     Up to 2GB Onboard DDR3 Memory;
     Up to 16GB Onboard eMMC NAND Flash
     Supports OpenGL ES 2.0 and OpenVG 1.1
     HDMI, 24-bit LVDS
     1x UART, 2x I2C, 8x GPIO,
     4x Host USB 2.0 port, 1x USB OTG port,
     1x micro SD (SDHC),1x SDIO, 1x SATA II,
     1x 10/100/1000 Mbps Ethernet, 1x PCIe X1 Gen2
 - Website: http://goo.gl/JED98USigned-off-by: NAkshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: NJustin Waters <justin.waters@timesys.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This patch adds vendor prefix for General Electric Company
Signed-off-by: NAkshay Bhat <akshay.bhat@timesys.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This patch adds vendor prefix for Advantech Corporation.
Website: http://www.advantech.com/Signed-off-by: NAkshay Bhat <akshay.bhat@timesys.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

For imx35, it needs three clocks to let the controller work,
the old code is wrong, and the usbmisc does not include
clock handling code any more.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

For imx25, it needs three clocks to let the controller work,
the old code is wrong, and usbmisc has not included clock
handling code any more.
Tested-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This patch adds the device node for the i.MX6UL keypad controller.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add the device node for the i.MX6UL GPMI interface and the related
APBH DMA which is necessary for the GPMI to work properly.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add the device node for the i.MX6UL eLCDIF interface.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add device nodes for the i.MX6UL synchronous audio interfaces (SAI).
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add device nodes for the i.MX6UL flexcan interfaces.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add device node for the i.MX6UL SDMA unit.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add device nodes for the PWM uinits 1..4 which were missing in the
original commit for i.MX6UL support.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Since PWMs are only useful if they are actually connected to an output pin,
let users enable them explicitly in their device trees where they should
also set up the pin configuration. This is in sync with a recent change
(commit e2675266 "ARM: dts: imx6qdl: disable PWMs by default")
to other i.MX SoCs.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

i.MX6UL PWMs require real clocks. Define the appropriate clocks for
the PWM units.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The i.MX6UL GPT unit requires real clocks. Define the appropriate
clocks to make it work.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

imx6ul.dtsi references the macro 'KEY_POWER' from
dt-bindings/input/input.h. Thus, move the include statement for this
file from imx6ul-14x14-evk.dts to imx6ul.dtsi itself.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Move the tsc node to keep the nodes sorted in ascending order by unit
address.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Pad DISPB2_SER_RS has no function DISP1_EXT_CLK.
The definition is obviusly a copy/paste error from
MX51_PAD_DISPB2_SER_RS__DISP1_PIN16.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Various pads are missing the input_sel offset and value. Fix this.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Remove whitespace before TAB in indentation and reduce indentation
level to improve readability.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add pinmux for UART_A RTS, CTS pin's.
Signed-off-by: NBhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

All Freescale Vybrid SoC include a Cortex-A5 core which supports
ARM's standard PMU (performance monitoring unit). Include the
monitoring unit into the Cortex-A5 base device tree vf500.dtsi.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The Colibri standard does not define a pin for SD-Card write-
protection. Use the disable-wp property to indicate that there
is no physical WP line present.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

According to the reference manual the shp_2_mcu / mcu_2_shp
scripts must be used for devices connected through the SPBA.

This fixes an issue we saw with DMA transfers from SPI NOR Flashes.
Sometimes the SPI controller RX FIFO was not empty after a DMA
transfer and the driver got stuck in the next PIO transfer when
it read one word more than expected.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add the carrier boards 3.3V supply as fixed regulator. This allows
to specify the power supply for nodes like backlight.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Colibri modules need to be powered using the power pins 3V3 and
AVDD_AUDIO. Add fixed regulators which represent this power rails.
Potentially, those power rails could be switched on a carrier
board. A carrier board device tree could add a own regulator with
a GPIO, and reference that regulator in a vin-supply property of
those new module level system regulators.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Drop the fake simple-bus container 'regulators' and put the
regulators directly under the root node. This also makes the
artificial 'reg' properties superfluous. While at it, remove
the unnecessary regulator-always-on property and name the
regulators according to schematics.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Assign Ethernet clock parents explicitly. The Colibri VF61
uses the 50MHz Ethernet clock provided by PLL5.

The Vybrid SoC has two ethernet interfaces (fec0 and fec1) which
use the same clock source (VF610_CLK_ENET). Therefore this parent
configuration affects multiple consumer devices and need to be
specified in the clock provider node.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Assign Ethernet clock parents explicitly. The VF610 Tower Board
uses the external Ethernet clock input which is connected to
a 50MHz clock.

The Vybrid SoC has two ethernet interfaces (fec0 and fec1) which
use the same clock source (VF610_CLK_ENET). Therefore this parent
configuration affects multiple consumer devices and need to be
specified in the clock provider node.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Signed-off-by: NSoeren Moch <smoch@web.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Remove the following unnecessary iomuxc container nodes:
imx6q-tbs2910
gpio_fan
gpio_leds

Sort the pinctrl nodes alphabetically.
Signed-off-by: NSoeren Moch <smoch@web.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Avoid the following warnings (example for usdhc2):
/soc/aips-bus@02100000/usdhc@02194000: voltage-ranges unspecified
sdhci-esdhc-imx 2194000.usdhc: could not get ultra high speed state,
                               work on normal mode
sdhci-esdhc-imx 2194000.usdhc: No vqmmc regulator found
Signed-off-by: NSoeren Moch <smoch@web.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Configure SATA PHY transmit level, boost, attenuation and equalizer
parameters for long wire connections. TBS2910 contains a standard SATA
connector, so devices are typically connected with (longer) SATA cables.
And explicitly configuring these parameters avoids complaints about
"not specified" values in boot messages.
Signed-off-by: NSoeren Moch <smoch@web.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Downstream packages like Debian flash-kernel use
/proc/device-tree/model
to determine which dtb file to install.

Hence each dts in the Linux kernel should provide a unique model
identifier.

Commit 8536239e ("ARM: dts: Restructure imx6qdl-wandboard.dtsi for new
rev C1 board.")' created new files imx6dl-wandboard-revb1.dts and
imx6q-wandboard-revb1.dts but used the same model identifier as in
imx6dl-wandboard.dts and imx6q-wandboard.dts.

This patch provides unique model identifiers for revision B1 of
the Wandboard Dual and Wandbaord Quad.

The patch leaves imx6dl-wandboard.dts and imx6q-wandboard.dts unchanged
because it is not foreseeable if the same dts will valid for future
board revisions or not. Furthermore we should avoid unnecessary
changes.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: NPetr Štetiar <ynezz@true.cz>
Reviewed-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: NPetr Štetiar <ynezz@true.cz>
Reviewed-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Uniwest evi is a portable electrical eddy current non-destructive
testing device.
Signed-off-by: NJoshua Clayton <stillcompiling@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>