For SEC including a RNG block version >= 4, special initialization
must occur before any descriptor that uses RNG block can be
submitted. This initialization is required not only for SEC
with version greater than 5.0, but for SEC with RNG version >=4.
There may be a case where RNG has already been instantiated by
u-boot or boot ROM code.In such SoCs, if RNG is initialized again
SEC would returns "Instantiation error". Hence, the initialization
status of RNG4 should be also checked before doing RNG init.
Signed-off-by: NRuchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: NAlex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Reviewed-by: NVakul Garg <vakul@freescale.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

This change is required for post SEC-5.0 devices which have RNG4.
Setting RDB in security configuration register allows CAAM to use the
"Random Data Buffer" to be filled by a single request. The Random Data
Buffer is large enough for ten packets to get their IVs from a single
request. If the Random Data Buffer is not enabled, then each IV causes a
separate request, and RNG4 hardware cannot keep up resulting in lower
IPSEC throughput if random IVs are used.
Signed-off-by: NVakul Garg <vakul@freescale.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

CONFIG_HOTPLUG is going away as an option.  As a result, the __dev*
markings need to be removed.

This change removes the use of __devinit, __devexit_p, __devinitdata,
and __devexit from these drivers.

Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.

Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

we need to configure the TRNG to use more clocks per sample
to handle the two back-to-back 64KiB random descriptor requests
on higher frequency P5040s.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

This patch adds support for retrieving and printing of
SEC ERA information. It is useful for knowing beforehand
what features exist from the SEC point of view on a
certain SoC. Only era-s 1 to 4 are currently supported;
other eras will appear as unknown.
Signed-off-by: NAlex Porosanu <alexandru.porosanu@freescale.com>

- rebased onto current cryptodev master
- made caam_eras static
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

The SEC v4.x' RNGB h/w block self-initialized.  RNG4, available
on SEC versions 5 and beyond, is based on a different standard
that requires manual initialization.

Also update any new errors From the SEC v5.2 reference manual:
The SEC v5.2's RNG4 unit reuses some error IDs, thus the addition
of rng_err_id_list over the CHA-independent err_id_list.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

SEC v4.x were only 36-bit, SEC v5+ are 40-bit capable.
Also set a DMA mask for any job ring devices created.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

In some device trees of previous version, there were string "fsl,sec4.0".
To be backward compatible with device trees, we have CAAM driver first
check "fsl,sec-v4.0", if it fails, then check for "fsl,sec4.0".
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

drivers/crypto/caam/ctrl.c: In function 'caam_probe':
drivers/crypto/caam/ctrl.c:49:6: warning: unused variable 'd' [-Wunused-variable]
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Access to the SEC4 DECOs (DEscriptor COntrollers) (for debug purposes)
isn't supported or used, and its register access initialization code
erroneously makes illegal i/o accesses that show up as errors when
run under simulation.  Remove it until proper support (via DECORR)
is added.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

This patch converts the drivers in drivers/crypto/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.

Cc: James Hsiao <jhsiao@amcc.com>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NVladimir Zapolskiy <vzapolskiy@gmail.com>
Acked-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

it will be replaced with S_IFREG anyway
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

drivers/crypto/caam/ctrl.c: In function 'caam_probe':
drivers/crypto/caam/ctrl.c:55:23: warning: unused variable 'perfmon'
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

this fixes a build error since cryptodev-2.6 got rebased
to include commit d714d197
"dt: eliminate of_platform_driver shim code".
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Help clarify that the number trailing in compatible nomenclature
is the version number of the device, i.e., change:

"fsl,p4080-sec4.0", "fsl,sec4.0";

to:

"fsl,p4080-sec-v4.0", "fsl,sec-v4.0";
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Cc: Kumar Gala <kumar.gala@freescale.com>
Cc: Steve Cornelius <sec@pobox.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

The SEC4 supercedes the SEC2.x/3.x as Freescale's
Integrated Security Engine.  Its programming model is
incompatible with all prior versions of the SEC (talitos).

The SEC4 is also known as the Cryptographic Accelerator
and Assurance Module (CAAM); this driver is named caam.

This initial submission does not include support for Data Path
mode operation - AEAD descriptors are submitted via the job
ring interface, while the Queue Interface (QI) is enabled
for use by others.  Only AEAD algorithms are implemented
at this time, for use with IPsec.

Many thanks to the Freescale STC team for their contributions
to this driver.
Signed-off-by: NSteve Cornelius <sec@pobox.com>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>