This is not used, and when we need to get the lowest rate
we should simply use mac80211's own rate_lowest_index(sband, sta).

Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This has no functional change and just cleans up the code
to be more legible and removes a useless variable for
Multi Rate Retry.

For regular frames we use 2 retries for MRR segments [0-2].
For the last MRR segment [3] we use 4.

MRR[0] = 2
MRR[1] = 2
MRR[2] = 2
MRR[3] = 4

Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The case where no vaid rate is found should not happen now
but to help debugging and downgrade this to a warn.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch roughly implements xmit aggregation for ar9170-like device.
Not all AP are compatible with the driver(and firmware) yet, so YMMV.

A more refined code will definitely need the final HT specification
to be available for the public, lots of firmware modification and
possibly a redesigned driver just for good measure.
Sadly, these conditions won't come true anytime soon...
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Two users of ar9170 devices have now reported their cards
have been programmed with a regulatory domain of 0x8000.
This is not a valid regulatory domain as such these users were
unable to use these devices. Since this doesn't seem to be
a device EEPROM corruption we must treat it specially. It
may have been possible the manufacturer intended to use 0x0
as the regulatory domain and that would ultimately yield
to US but since we cannot get confirmationf or this we
default this special case to one of our world regulatory
domains, specifically 0x64.

Reported-by: DavidFreeman on #linux-wireless
Reported-by: NJoerg Albert <jal2@gmx.de>
Cc: Christian Lamparter <chunkeey@web.de>,
Cc: Stephen Chen <stephen.chen@atheros.com>
Cc: David Quan <david.quan@atheros.com>
Cc: Tony Yang <tony.yang@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For AP mode we must tune ANI specially for 2 GHz and
for 5 GHz. We mask in only the flags we want to toggle
on ath9k_hw_ani_control() through the ah->ani_function
bitmask, this will take care of ignoring changes during
ANI reset which we were disabling before.
Testedy-by: NSteven Luo <steven@steven676.net>
Cc: Bennyam Malavazi <bennyam.malavazi@atheros.com>
Cc: Jouni Malinen <jouni.malinen@Atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Pavel Roskin reported some issues with using AP mode without
nohwcrypt=1.  Most likely this is similar to the problem fixed
some time ago in ath9k by 3f53dd64,
"ath9k: Fix hw crypto configuration for TKIP in AP mode."

That only affects TKIP but it's easiest to just disable that and
WEP too until we get a proper fix in.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"Ath5k: unify resets"
introduced a regression into 2.6.28 where the PCU registers are never
initialized, due to ath5k_reset() always passing true for change_channel.
We subsequently program a lot of these registers but several may start
in an unknown state.

Cc: stable@kernel.org
Reported-by: NForrest Zhang <forrest@hifulltech.com>
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Paraphrasing Rafael J. Wysocki: "drivers should not release PCI IRQs
in suspend."  Doing so causes a warning during suspend/resume on some
platforms.

Cc: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: NAlan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

'default' case already returns NO_CTL
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using the enable_beacon flag allows some simplifications and fixes
some corner cases in beacon handling.  This change adds a state
variable for beaconing in ath5k_beacon_config and handles both
enabling and disabling, thus eliminating the need for
ath5k_beacon_disable.  We also now configure the beacon when any
of the beacon parameters change, so ath5k_beacon_reconfig is no
longer needed (its mmiowb gets moved to ath5k_beacon_config).
Finally, by locking around the whole config function, we don't
need to worry about clearing the interrupt mask register before
installing the new mask.

The upshot is this correctly disables beaconing when the interfaces
are taken down, it fixes a potential restarting of beaconing
when ath5k_reset() is called, and ensures that updates to the
beacon interval take effect immediately.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable the "Content" After Beacon queue and utilize it to send
any buffered frames for power-saving clients.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't allow users to open debugfs files, because it can cause oopses.

When a user opens some file, driver unlinks it and frees the
corresponding structure, we will dereference freed memory.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't allow users to open debugfs files, because it can cause oopses.

When a user opens some file, driver unlinks it and frees the
corresponding structure, we will dereference freed memory.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes an issue when the TX and RX streams are different.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ANI calibration shouldn't be done when we are not on our home channel.
This is already verified. However, it is racy. Fix this by proper
spin locks.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ANI is not required when the STA is disconnected. So stop it and enable
ANI for adhoc and monitor mode.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove unncessary STATION mode check in ath9k_bss_assoc_info() as
it is called only for STATION mode.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Andrey Yurovsky reported that the driver forwarded erroneously the
parent device structure instead of the real thing, which of course
led to some dodgy sysfs links (at least?).
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We were not differentiating quality between legacy and HT
configurations. We change this to consider the differences.

New theory for reporting quality:

At a hardware RSSI of 45 you will be able to use MCS 7  reliably.
At a hardware RSSI of 45 you will be able to use MCS 15 reliably.
At a hardware RSSI of 35 you should be able use 54 Mbps reliably.

MCS 7  is the highets MCS index usable by a 1-stream device.
MCS 15 is the highest MCS index usable by a 2-stream device.

All ath9k devices are either 1-stream or 2-stream.

How many bars you see is derived from the qual reporting.

A more elaborate scheme can be used here but it requires tables
of SNR/throughput for each possible mode used. For the MCS table
you can refer to the wireless wiki:

http://wireless.kernel.org/en/developers/Documentation/ieee80211/802.11n

This should fix this bug report:

http://bugzilla.kernel.org/show_bug.cgi?id=13537

Cc: Janath.Peiris@atheros.com
Cc: Matt.Smith@atheros.com
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This helper only clears the SC_OP_WAIT_FOR_{BEACON,CAB} flags.
Remove it and clear these flags directly in the approptiate
places instead.

Changes-licensed-under: ISC
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All SC_OP_WAIT_* flags will be cleared in 'ath9k_conf' when PS mode
is disabled, so we don't have to clear it here.

Changes-licensed-under: ISC
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Within mac80211, we often need to copy the rx status into
skb->cb. This is wasteful, as drivers could be building it
in there to start with. This patch changes the API so that
drivers are expected to pass the RX status in skb->cb, now
accessible as IEEE80211_SKB_RXCB(skb). It also updates all
drivers to pass the rx status in there, but only by making
them memcpy() it into place before the call to the receive
function (ieee80211_rx(_irqsafe)). Each driver can now be
optimised on its own schedule.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch moves the sanity check on beacon interval
which was done only for mesh mode to all operating
modes just to be safe.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cardbus and some PCI cards use hardware LEDs rather than software GPIOs.
Program them with the proper blink patterns when idle, scanning or
associated.  Fixes http://bugzilla.kernel.org/show_bug.cgi?id=13288.
Tested-by: NFrans Pop <elendil@planet.nl>
Tested-by: NMark Hindley <mark@hindley.org.uk>
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ah_gpios array isn't used, and ah_current_channel can be a pointer
instead of an embedded struct.  Removing these and some other
write-only variables, and moving some things around for better
packing and cache utilization saves 116 bytes.

   text	   data	    bss	    dec	    hex	filename
 121762	    472	     64	 122298	  1ddba	ath5k_before.ko
 121646	    472	     64	 122182	  1dd46	ath5k.ko
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We can easily run out of tx buf if there is any stuck in
transmission, so downgrade it to WARN_ON().
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mac80211 already has one to keep track of number of failure
addba attempts.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

IEEE80211_TX_CTL_AMPDU in tx control flags should be enough
to confirm BA is negotiated for that tid.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Atheros top level menu needs a "depends WLAN_80211" to properly indent
within menuconfig and xconfig interfaces.

This is purely a visual issue but it effects all subsequent drivers.
The issue is the top level menu does not include a dependency on
WLAN_80211 so within the tree structure, Atheros is at the same level as
WLAN_80211 but when WLAN_80211 collapsed, the menu disappears along with
all subsequent drives, so it is really a subordinate.
Signed-off-by: NJay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we reclaim the tx desc, we always assume that the
last desc is a holding desc, which is not true, and skip it.
If the tx queue is drained during channel change, internal
reset and etc, the last descriptor may not be the holding
descriptor and we fail to reclaim them. This results in the
following two issues.

1. Tx stuck - We drop all the frames coming from upper layer
due to shortage in tx desc.

2. Crash - If we fail to reclaim a tx descriptor, we miss to
update the tx BA window with the seq number of the frame
associated to that desc, which, at some point, result in
the following crash due to an assert failure in ath_tx_addto_baw().

This patch fixes these two issues.

 kernel BUG at ../drivers/net/wireless/ath/ath9k/xmit.c:180!
[155064.304164] invalid opcode: 0000 [#1] SMP
 Call Trace:
  [<fbc6d83b>] ? ath9k_tx+0xeb/0x160 [ath9k]
  [<fbbc9591>]  ipv6? __ieee80211_tx+0x41/0x120 [mac80211]
  [<fbbcb5ae>] ?  aes_i586ieee80211_master_start_xmit+0x28e/0x560 [mac80211]
  [<c037e501>]  aes_generic? _spin_lock_irqsave+0x31/0x40
  [<c02f347b>] ? dev_hard_start_xmit+0x16b/0x1c0
  [<c03058b5>] ? __qdisc_run+0x1b5/0x200
  [<fbbcda5a>] ?  af_packetieee80211_select_queue+0xa/0x100 [mac80211]
  [<c02f53b7>] ?  i915dev_queue_xmit+0x2e7/0x3f0
  [<fbbc9b49>] ? ieee80211_subif_start_xmit+0x369/0x7a0 [mac80211]
  [<c031bc35>] ? ip_output+0x55/0xb0
  [<c02e0188>] ? show_memcpy_count+0x18/0x60
  [<c02eb186>] ? __kfree_skb+0x36/0x90
  [<c02f2202>] ?  binfmt_miscdev_queue_xmit_nit+0xd2/0x110
  [<c02f347b>] ? dev_hard_start_xmit+0x16b/0x1c0
  [<c03058b5>] ? __qdisc_run+0x1b5/0x200
  [<c033bca7>] ?  scoarp_create+0x57/0x2a0
  [<c02f53b7>] ?  bridgedev_queue_xmit+0x2e7/0x3f0
  [<c03034a0>] ? eth_header+0x0/0xc0
  [<c033b95f>]  stp? arp_xmit+0x5f/0x70
  [<c033bf4f>] ? arp_send+0x5f/0x70
  [<c033c8f5>]  bnep? arp_solicit+0x105/0x210
  [<c02fa5aa>] ? neigh_timer_handler+0x19a/0x390
  [<c013bf88>] ? run_timer_softirq+0x138/0x210
  [<c02fa410>] ?  ppdevneigh_timer_handler+0x0/0x390
  [<c02fa410>] ? neigh_timer_handler+0x0/0x390
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

73ca5203
(ath5k: remove conf->beacon_int usage)
removed bintval setting from ath5k_config. We need to init the
interval earlier and don't touch it in add_interface anymore.

Otherwise it will be set only once by upper layer through
bss_info_changed but not on second and further hostap executions.

We ended up having bintval 1000 which rendered the AP useless on
many clients.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Bob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We want to put the chip into FULL SLEEP state, when we are disabling the
radio, but the the current code always change it to AWAKE/NETWORK SLEEP.

Changes-licensed-under: ISC
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Changes-licensed-under: ISC
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts 'ath5k: remove dummy PCI "retry timeout" fix' on the
same theory as in 'ath9k: Fix PCI FATAL interrupts by restoring
RETRY_TIMEOUT disabling'.
Reported-by: NBob Copeland <me@bobcopeland.com>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

An earlier commit, 'ath9k: remove dummy PCI "retry timeout" fix', removed
code that was documented to disable RETRY_TIMEOUT register (PCI reg
0x41) since it was claimed to be a no-op. However, it turns out that
there are some combinations of hosts and ath9k-supported cards for
which this is not a no-op (reg 0x41 has value 0x80, not 0) and this
code (or something similar) is needed. In such cases, the driver may
be next to unusable due to very frequent PCI FATAL interrupts from the
card.

Reverting the earlier commit, i.e., restoring the RETRY_TIMEOUT
disabling, seems to resolve the issue. Since the removal of this code
was not based on any known issue and was purely a cleanup change, the
safest option here is to just revert that commit. Should there be
desire to clean this up in the future, the change will need to be
tested with a more complete coverage of cards and host systems.

http://bugzilla.kernel.org/show_bug.cgi?id=13483

Cc: stable@kernel.org
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Many developers use "/debug/" or "/debugfs/" or "/sys/kernel/debug/"
directory name to mount debugfs filesystem for ftrace according to
./Documentation/tracers/ftrace.txt file.

And, three directory names(ex:/debug/, /debugfs/, /sys/kernel/debug/) is
existed in kernel source like ftrace, DRM, Wireless, Documentation,
Network[sky2]files to mount debugfs filesystem.

debugfs means debug filesystem for debugging easy to use by greg kroah
hartman. "/sys/kernel/debug/" name is suitable as directory name
of debugfs filesystem.
- debugfs related reference: http://lwn.net/Articles/334546/

Fix inconsistency of directory name to mount debugfs filesystem.

* From Steven Rostedt
  - find_debugfs() and tracing_files() in this patch.
Signed-off-by: NGeunSik Lim <geunsik.lim@samsung.com>
Acked-by     : Inaky Perez-Gonzalez <inaky@linux.intel.com>
Reviewed-by  : Steven Rostedt <rostedt@goodmis.org>
Reviewed-by  : James Smart <james.smart@emulex.com>
CC: Jiri Kosina <trivial@kernel.org>
CC: David Airlie <airlied@linux.ie>
CC: Peter Osterlund <petero2@telia.com>
CC: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
CC: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
CC: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If we are in PS mode, we have to process the received frame if
the SC_OP_WAIT_FOR_CAB bit is set.

Changes-licensed-under: ISC
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We have to remain awake if the SC_OP_WAIT_FOR_CAB flag is set.

Changes-licensed-under: ISC
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>