If the input is ADV7604_INPUT_VGA_RGB and RGB quantization range is
set to V4L2_DV_RGB_RANGE_AUTO, video with CEA timings will be
received as RGB. For ADV7604_INPUT_VGA_COMP, automatic CSC mode
will be selected.

See table 44 on page 205 in "ADV7604 Hardware Manual, Rev. F, August 2010"
for details.
Signed-off-by: NMats Randgaard <matrandg@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The driver strength is board dependent, so set it from the platform_data.
Signed-off-by: NMikhail Khelik <mkhelik@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The adv7604 supports four digital input ports. This patch adds support
for all of them, instead of just port A.
Signed-off-by: NMats Randgaard <matrandg@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Ignore EDID's where the header is wrong.
Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Improve status logging.
Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Whenever the hotplug pin is pulled low the chip resets a whole bunch
of registers. It turns out that this can be turned off on the adv7511.
Do so, as this 'feature' introduces race conditions in setting up
registers, particular when the hotplug pin bounces a lot.
Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Retry setup if the device is powered off when it should be powered on. This
state can be caused by rapid hotplug toggles.
Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Removed dependency on rx-sense interrupt, it's a leftover from obsolete
code. Removing this simplifies the code.
Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Ignore EDIDs where the header is wrong.
Signed-off-by: NMats Randgaard <matrandg@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Instead of using two I2C operations between write and read,
use just one i2c_transfer. That allows I2C mutexes to not
let any other I2C transfer between the two.
Reviewed-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Tested-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Driver for Samsung S5K5BAF UXGA 1/5" 2M CMOS Image Sensor with
embedded SoC ISP. The device is exposed as two V4L2 subdevices:

 - S5K5BAF-CIS - the image sensor matrix, fixed 1600x1200 format,
   no controls.
 - S5K5BAF-ISP - the Image Signal Processor, formats up to 1600x1200,
   pre/post ISP cropping, downscaling via selection API, controls.

[m.chehab@samsung.com: Whitespace cleanups]
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The omap24xx driver and the tcm825x sensor driver are the only two
remaining drivers to still use the old deprecated v4l2-int-device API.

Nobody maintains these drivers anymore. But unfortunately the v4l2-int-device
API is used by out-of-tree drivers (MXC platform). This is a very bad situation
since as long as this deprecated API stays in the kernel there is no reason for
those out-of-tree drivers to convert.

This patch moves v4l2-int-device and the two drivers that depend on it to
staging in preparation for their removal.

If someone would be interested in getting these drivers to work, then start with
this since it's not very far from the state where they used to work:

<URL:http://vihersipuli.retiisi.org.uk/cgi-bin/gitweb.cgi?p=~sailus/linux-omap/.git;a=summary>

The branch is n800-cam. Porting to up-to-date APIs can then be done. David
might have done some work in that area, so check with him first.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: David Cohen <dacohen@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The MT9V034 sensor is very similar to the MT9V032, with a couple of
different registers and parameters.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

To prepare support of the MT9V034, add the necessary infrastructure to
support model-specific parameters.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Identify the model based on the I2C device name and configure formats
accordingly.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The sensor can scale the image down using binning by 1, 2 or 4 in both
directions. Update size enumeration and ratio and binning factor
computation accordingly.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The active pixel array size is 753x481 with 4 additional black rows at
the top. Fix the driver accordingly.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The EXT_CLK macro is unused, remove it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

vs6624_read() is only called in the conditionally-compiled
vs6624_g_register() function. Make the former conditionally-compiled as
well to silence build warnings.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NScott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

We had set the i2c clientdata to &flash->subdev_led[LM3560_LED1]
after call lm3560_subdev_init(flash, LM3560_LED1, "lm3560-led1"),
but the container_of() in lm3560_remove() return the wrong pointer
to flash.(should be container_of(subdev, struct lm3560_flash,
subdev_led[LM3560_LED_MAX-1])
This patch fix to set i2c clientdata to flash so we can get flash
from clientdata directly.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add the missing unlock before return from function lm3560_set_ctrl()
in the error handling case.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

git grep shows that the function is only called from ths7303.c
Fix this build warning:
CC      drivers/media/i2c/ths7303.o
drivers/media/i2c/ths7303.c:86:5: warning: no previous prototype for  ‘ths7303_setval’ [-Wmissing-prototypes]
   int ths7303_setval(struct v4l2_subdev *sd, enum ths7303_filter_mode mode)
        ^
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Fix various spelling errors in strings and comments throughout the media
tree. The majority of these were found using Lucas De Marchi's codespell
tool.

[m.chehab@samsung.com: discard hunks with conflicts]
Signed-off-by: NJonathan McCrohan <jmccrohan@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Correct reference of reading values. (rval -> reg_val)
Add the missing unlock before return from function lm3560_get_ctrl()
to avoid deadlock.
Thank you Dan Carpenter & Sakari.
Signed-off-by: NDaniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

internal_csi_format_idx and csi_format_idx are unsigned integers,
therefore they can never be nevative.
CC      drivers/media/i2c/smiapp/smiapp-core.o
In file included from include/linux/err.h:4:0,
                 from include/linux/clk.h:15,
                 from drivers/media/i2c/smiapp/smiapp-core.c:29:
drivers/media/i2c/smiapp/smiapp-core.c: In function ‘smiapp_update_mbus_formats’:
include/linux/kernel.h:669:20: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
 #define min(x, y) ({    \
                    ^
include/linux/compiler.h:153:42: note: in definition of macro ‘unlikely’
 # define unlikely(x) __builtin_expect(!!(x), 0)
                                          ^
drivers/media/i2c/smiapp/smiapp-core.c:402:2: note: in expansion of macro ‘BUG_ON’
  BUG_ON(min(internal_csi_format_idx, csi_format_idx) < 0);
  ^
drivers/media/i2c/smiapp/smiapp-core.c:402:9: note: in expansion of macro ‘min’
  BUG_ON(min(internal_csi_format_idx, csi_format_idx) < 0);
         ^
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

git grep shows that the function is only called from ths7303.c
Fix this build warning:
CC      drivers/media/i2c/ths7303.o
drivers/media/i2c/ths7303.c:86:5: warning: no previous prototype for  ‘ths7303_setval’ [-Wmissing-prototypes]
   int ths7303_setval(struct v4l2_subdev *sd, enum ths7303_filter_mode mode)
        ^
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Fix various spelling errors in strings and comments throughout the media
tree. The majority of these were found using Lucas De Marchi's codespell
tool.

[m.chehab@samsung.com: discard hunks with conflicts]
Signed-off-by: NJonathan McCrohan <jmccrohan@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Commit 5aa9ae5e inverted the mute control
state test in s_routing which caused the audio routing to fail. This broke
ivtv support for the Hauppauge video/audio input bracket (which adds additional
video and audio inputs) all the way back in kernel 2.6.36.
This fix fixes the condition and it also removes a nonsense check on the
balance control.
Bisected-by: NRajil Saraswat <rajil.s@gmail.com>
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Reported-by: NRajil Saraswat <rajil.s@gmail.com>
Tested-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org      # for v3.10 and up
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Adds the driver for the LM3560, dual LED Flash The LM3560 has two 1A
constant current driver for high current white LEDs.

It is controlled via an I2C compatible interface(up to 400kHz).

Each flash brightness, torch  brightness and enable/disable can be
controlled independantly, but flash timeout and operation mode are shared.
Signed-off-by: NDaniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

v3.12-rc fails to build with this error:
drivers/media/i2c/ths8200.c:49:2: error: unknown field 'bt' specified in initializer
drivers/media/i2c/ths8200.c:50:3: error: field name not in record or union initializer
drivers/media/i2c/ths8200.c:50:3: error: (near initialization for 'ths8200_timings_cap.reserved')
drivers/media/i2c/ths8200.c:51:3: error: field name not in record or union initializer
drivers/media/i2c/ths8200.c:51:3: error: (near initialization for 'ths8200_timings_cap.reserved')
...
with gcc 4.5.4.  This error was not detected in builds prior to v3.12-rc.
This patch fixes this.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Cc: stable@vger.kernel.org # For kernel v3.12
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

If v4l2_async_register_subdev() fails, don't skip the clean up.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>